Knowledge Builders

how do you fix a flush tank handle

by Myrtle Gibson Published 2 years ago Updated 1 year ago
image

How to Fix or Replace a Toilet Flush Handle

  • Step 1: Turn Off the Water Remove the tank lid and set it aside. ...
  • Step 2: Disconnect the Old Toilet Handle Unhook the flapper chain from the lever. ...
  • Step 3: Remove the Old Flush Handle Slide the nut down the length of the lever. ...
  • Step 4: Install the New Flush Handle ...
  • Step 5: Connect the Flapper Chain ...

Part of a video titled How to Fix a Toilet - Toilet Handle Replacement - YouTube
0:59
2:26
Disconnect the flapper chain from the flush handle and hook it over the toilets overflow tubeMoreDisconnect the flapper chain from the flush handle and hook it over the toilets overflow tube located. In the center of the toilet. Take an adjustable open end wrench and unscrew the tank lever nut.

Full Answer

How do you fix a toilet that won't flush?

Possible Causes & How to Fix 1 Handle. Take the cover off the toilet tank and locate the mounting nut of the handle. ... 2 Lift Arm. While still inside the tank, check the arm lever to see if it’s bent or needs some other kind of fixing. 3 The Chain. The length of the chain can significantly affect how the flush cycle occurs. ... 4 The Flapper. ...

How do you remove the flapper from a toilet tank?

Flush the toilet to empty the tank of water. Unhook the chain from the flush arm. There is usually a small clip that hooks onto the arm. With the flush arm in the down position and the flapper at rest on the flush valve, pull the chain straight up so there is no slack, and align the chain with one of the holes in the arm.

How do you remove the handle on a toilet tank?

Take the cover off the toilet tank and locate the mounting nut of the handle. It should be directly opposite the handle from inside the porcelain. Take an adjustable wrench and begin removing the handle by turning the nut clockwise. You should have unhooked the chain from the arm lever by now.

What do you do if your water tank handle is stuck?

Note: If the extra chain is long enough to get stuck under the flapper, cut off some of the excess with wire cutters. Turn the water back on (if you turned it off). Let the tank fill back up and test your work. If the handle is still sticking, you can take more slack out of the chain.

image

How do you fix a flush tank lever?

0:493:10Plumbing - Replace Toilet Tank Lever Video - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd attach our nut to the back side of it. And then slightly tighten it up you don't want to overMoreAnd attach our nut to the back side of it. And then slightly tighten it up you don't want to over tighten this else it won't turn well just snug it down there you can link with our crescent wrench.

How do you fix a broken flush handle?

0:141:42How To Replace A Broken Flush Handle - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's usually made of plastic unscrew. The nut that holds the handle in place this. Can be a bitMoreIt's usually made of plastic unscrew. The nut that holds the handle in place this. Can be a bit tricky as this nut is reverse threaded which means you must turn it clockwise to undo remove the handle.

Why is the flush handle not working?

The handle becomes either too loose or too tight, which stops it connecting with the link and flushing mechanism. Sometimes, it can be fixed by simply tightening the mounting nut at the back of the handle. The handle may also have become stiff due to a build-up of limescale.

Can you replace the handle on a toilet?

If your toilet handle is loose or hangs down, it won't properly allow you to flush your toilet, so you need to get a replacement. Toilet handles are easy to remove and install on your own in around 15 minutes. All you need to do is unscrew the old handle and then put the new handle in its place.

How do you fix a toilet handle without a chain?

1:296:04How to Replace a Toilet Handle without a chain - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd there's the hole. All right so now we just got to take our new one and this is the we ended upMoreAnd there's the hole. All right so now we just got to take our new one and this is the we ended up with a fluid master universal toilet tank lever this one's brass. And it's replacing.

How do you fix a flush valve?

0:402:00How to Install a New Flush Valve - YouTubeYouTubeStart of suggested clipEnd of suggested clipThen remove the tank and gently place it upside down on an old towel or rug. Now unscrew the spudMoreThen remove the tank and gently place it upside down on an old towel or rug. Now unscrew the spud nut with a wrench or pair of slip-joint pliers.

Why is my toilet handle getting stuck down?

First, check to see if the chain that is attached to the ball in your tank is snagging against something. If the chain is stuck, your toilet handle will feel more difficult to push. Make Sure the Chain is the Right Length. When you flush your toilet, the flapper or seal should rise (about 90 degrees).

Why do I have to pump the toilet handle to flush?

The problem is caused by too much slack in the lifting chain that connects the flush lever to the flapper. When the chain has too much slack, it cannot lift the flapper high enough to allow the full amount of water to flow down through the flush valve; it closes prematurely, stopping the flush.

How do you fix a flush valve?

0:402:00How to Install a New Flush Valve - YouTubeYouTubeStart of suggested clipEnd of suggested clipThen remove the tank and gently place it upside down on an old towel or rug. Now unscrew the spudMoreThen remove the tank and gently place it upside down on an old towel or rug. Now unscrew the spud nut with a wrench or pair of slip-joint pliers.

How do you replace a lift arm on a toilet?

Buy a New Handle. Before purchasing a new toilet handle, check to see where the handle is located on your toilet tank. ... Remove the Toilet Lid. Lift the lid from toilet tank. ... Detach the Lift Chain. ... Remove the Handle Mounting Nut. ... Remove the Old Handle. ... Insert the New Handle. ... Fasten the New Handle. ... Attach the Chain and Test.

Why is my toilet handle facing up?

Too much water means the float is overstretched causing the handle to point upwards due to the tension inside the tank. Unfortunately, if the seal is broken, so is the valve and vice versa. The best thing to do is to also replace the flush valve so the water only fills up to the exact level without leaking.

Why do I have to pump the toilet handle to flush?

The problem is caused by too much slack in the lifting chain that connects the flush lever to the flapper. When the chain has too much slack, it cannot lift the flapper high enough to allow the full amount of water to flow down through the flush valve; it closes prematurely, stopping the flush.

Where is the flush handle on a toilet?

Toilet manufacturers place the flush handle on the front or the side of the toilet or on the left or right side. These companies produce flush handle assemblies — the handle and the lever — for specific toilet models. There are a variety of finishes available. Some manufacturers create flush handles with finishes that match ...

How to loosen a toilet handle?

Unhook the flapper chain from the lever. Unscrew the lock nut on the inside of the tank that secures the handle to the tank. The nut and stem have reverse threads, so turn the nut clockwise rather than counterclockwise to loosen it. If the nut is stuck or if it's made of metal, use a wrench to unscrew it. It is important to turn the nut in the right direction; if you overtighten it by mistake, you could crack the toilet tank.

How to tighten a toilet nut?

To tighten it, remove the toilet tank top and place it out of the way. This nut and the stem to which you attach it have reverse threads, meaning that the threads go in the opposite direction than you may be used to. To tighten a standard thread nut, you turn it clockwise, or to the right. With reverse threads, you turn in ...

What is the handle on a toilet?

The toilet handle starts the whole flushing process. The handle is connected to a lever, or arm, that is inside the toilet tank. The lever is the attachment point for a chain that connects the lever arm to the toilet's flapper on the bottom of the tank. When you use the toilet handle, the flapper opens, and the water in the tank flows to ...

How to drain a toilet when it's full?

Remove the tank lid and set it aside. Close the shutoff valve that is located on the wall or floor near the toilet. Turn the valve clockwise to stop the flow of water. Then, flush the toilet to drain the tank. Some people skip this step, but working in the tank when it is full can be bothersome.

What does it mean when the toilet handle doesn't work?

The flush handle on a toilet gets a lot of use, and it can break over time, which effectively means the toilet won't work.

How much slack should be in a toilet chain?

There should be about 1/2 inch of slack in the chain. If it is too taut, the chain may prevent the flapper from sealing properly. If it is too loose, the flapper may not open all the way, interfering with the flush. Test it by turning on the water and flushing the toilet.

What happens if you don't hold the handle on a flush valve?

If you don't hold the handle, the flapper drops back down over the flush valve, shutting off the water flow.

How to align a flush valve chain?

With the flush arm in the down position and the flapper at rest on the flush valve, pull the chain straight up so there is no slack, and align the chain with one of the holes in the arm. Pinch the chain link nearest this hole.

How to check slack in toilet chain?

Check the slack in the chain when you operate the toilet handle. When the handle is depressed, the flapper should lift into a nearly vertical position so you can see the bottom of the flapper. When you release the handle, the flapper should settle down into the flush valve, with just a small amount of slack in the chain.

Why is my toilet handle stuck?

The "stuck" toilet handle appears to occur for no obvious reason, although the cause is remarkably simple. You can start to understand what is happening if you simply remove the lid from the toilet and watch the parts in action as you depress the toilet handle. When operating normally, the flush arm pulls on a lift chain ...

What to do if your flapper is corroding?

If the flapper still gives you problems, simply replace it with a new one that fits your flush valve. Flappers cost only a few dollars and are sold at all home centers. Be sure to replace the old chain, too, as these eventually corrode and can break.

What to do if you don't have a shutoff valve?

If you don't have a shutoff valve near the toilet, don' t worry about it: you can easily fix this problem without shutting the water off at all, though you will get your hands wet. Don't worry; the water in the toilet tank is fresh. Steve Hallo.

Where is the water shut off valve on a toilet?

Turn off the water at the fixture shutoff valve, which is usually located near the left side of the toilet tank, where the water supply pipe comes up through the floor or out from the wall. If you don't have a shutoff valve near the toilet, don't worry about it: you can easily fix this problem without shutting the water off at all, though you will get your hands wet. Don't worry; the water in the toilet tank is fresh.

How to tighten a toilet handle?

Tightening toilet handle nut. Remove the lid from the toilet tank and set it aside safely. Turn off water to your toilet either through the immediate shutoff valve or the main shutoff valve.

Why is the Toilet Flush Handle Loose?

A slack flush handle is one that jiggles by itself without tension and in most cases won’t flush properly. As mentioned earlier your toilet tank handle can be loose because of any of the following

What does a loose handle on a tank mean?

A loose handle can easily mean you’re not initiating the handle, to begin with. Because the handle is fixed by reverse-threading, just tighten the nut by turning counterclockwise. Lastly, check the base of the tank where the flapper is to confirm the lift arm is also well connected to the flapper.

Why does my toilet handle slack?

The most obvious reason of loosening is wear and tear. The handle can also slack due to a disconnection or unfastened chain inside the toilet tank. You can simply fix this problem by replacing the handle, reconnecting the chain to the handle so it can gain pressure from the flapper underneath.

What is the valve on a toilet tank called?

Once you open the top part of the toilet tank, you will notice the handle from the inside is hooked to a valve called the flapper which opens up a leeway for water to get in.

What happens if the lift chain is loose?

If it’s loose, there will be no pressure to lift the flapper high enough to release water for a flush cycle. Adjust the chain length to just one inch approximately from the lever this way once you flush it will open the flapper completely.

How to turn a nut in a tank?

It should be directly opposite the handle (behind the porcelain). Take an adjustable wrench and try to turn the nut in a counterclockwise direction. Regulate your speed and tension until it’s snug.

What happens when the flushing valve becomes visible?

When the flushing valve becomes visible, lift the float as high as it goes, and by the effect of this valve, the toilet will flush.

What kind of stick to use to remove flapper valve?

Because of the other components involved, it might be difficult to reach the flapper valve, so it would be more convenient to use a wooden or a metal stick for the removal.

What happens when you let go of the handle to make the cistern refill?

When you let go of the handle to make the cistern refill, the tilt lever opens up a ball valve and water under big pressure enters the cistern and refills it so you can use and flush the toilet again. When the water reaches the desired level, the float will stop the water supply. When you know these simple facts, ...

How does a toilet handle work?

The toilet flushing mechanism works by operating many levers inside the cistern by simple moving ...

When does a toilet float stop water supply?

When the water reaches the desired level, the float will stop the water supply. When you know these simple facts, it is not that hard to operate the flushing mechanism without the handle since you know the purpose of the toilet handle.

Where is the flapper valve located in a siphon?

In most cases, it is located at the center bottom of the cistern. Because of the other components involved, it might be difficult to reach the flapper valve, so it would be more convenient to use a wooden or a metal stick for the removal.

Can you pull the string out of a toilet?

On toilets which have their handle physically connected to the flapper valve, be sure to watch out when pulling the string, as it may get easily pulled out.

How to loosen a tank handle?

Locate the plastic or metal mounting nut that's holding your handle in place on the inside the top of the tank. Try twisting the nut clockwise by hand to see if you can loosen it. If not, grip the nut with a pair of locking pliers to get better leverage on it.

What to do if your toilet doesn't flush?

If your toilet doesn't flush at all, make sure the chain clip is attached to the lever properly.

What to do if a toilet nut is stripped?

If the nut inside your toilet is stripped, use a hacksaw to cut through it.

How long does it take to remove a toilet handle?

Toilet handles are easy to remove and install on your own in around 15 minutes. All you need to do is unscrew the old handle and then put the new handle in its place.

What to do if toilet handle doesn't work?

If the new handle still doesn't work after you install it, contact a plumber to find the problem with your toilet.

How to undo a toilet flapper?

Undo the chain clip attached to the lever. The chain clip attaches the handle to the flapper and lets you flush your toilet. Look for the section of chain clasped to the end of the metal or plastic lever that connects to the handle. Undo the clasp to detach the handle and lever from the rest of your toilet.

Where to hang toilet chain?

Hang the clasped end of the chain over the side of the toilet or on the pipe of the fill pump so it's easier to reattach later on.

What does it mean when a flush handle is sticky?

If the handle is sticky it means after the flush, the handle cant return smoothly as it’s gummed up. Remove every speck of dirt you see. Reconnect the handle and tighten the mounting nut by turning it counterclockwise. Don’t exert too much force.

How far should the arm of a tank be from the handle?

While still inside the tank, check the arm lever to see if it’s bent or needs some other kind of fixing. The arm should be straight measuring about 1 inch from the handle.

Why does my toilet tank never spring back?

Some of the reasons your toilet tank handle stays down and never springs back include; A stuck handle that doesn’t easily glide back up after a flush. A disconnected chain that doesn’t pull back the lever which in turn should raise the handle back. A failing flapper that causes the water not to refill to its maximum capacity, ...

What does a flapper do to a toilet?

The Flapper. Lastly, check the flapper that releases water to the toilet bowl once a flush has been initiated. This will be the last course of action before you call for plumbing services. The flapper will mostly affect the speed of the refill, chain inability move, or the flush size.

Why won't my toilet handle spring back up?

But wait, it won’t spring back up after flushing. More often than not, if the handle isn’t working as it is supposed to work, it means any of the toilet tank’s interior components is faulty. For instance, it could mean the chain is loose, disconnected, or too long. Basic inspection of the tank can lead you to where the issue is.

What to do if your lever is bent?

Don’t try to change that. If it’s wrongly bent, use the adjustable wrench or pliers to straighten it out. Check how the lever/ arm affects the flapper beneath.

What to do if water never reaches the level it should?

If the water never reaches the level it should, then the handle can get to the position it should. Therefore, check the flapper at the base of the toilet for any leaks. This is mainly indicated when the water level in the tank is too low. Also, if the refill time is extremely long.

image

1.Videos of How Do You Fix a Flush Tank Handle

Url:/videos/search?q=how+do+you+fix+a+flush+tank+handle&qpvt=how+do+you+fix+a+flush+tank+handle&FORM=VDRE

28 hours ago  · Fixing or replacing a broken flush lever or toilet handle is an easy five minute job that anyone can do. Did this video help you? I'd love to hear about it! ...

2.How to Fix or Replace a Toilet Handle / Flush Lever

Url:https://www.youtube.com/watch?v=Tw9hv2fQFmw

8 hours ago  · This video explains how to replace the toilet tank lever when the original lever is broken.You can find an inexpensive repair kit online or at the local hard...

3.Fixing a Toilet Tank Flush Handle - easy DIY - YouTube

Url:https://www.youtube.com/watch?v=znw-CHwrLYI

26 hours ago How do you fix a stuck flush? Unhook the chain from the flush arm. There is usually a small clip that hooks onto the arm. With the flush arm in the down position and the flapper at rest on the …

4.How to Fix a Stuck Toilet Handle - The Spruce

Url:https://www.thespruce.com/stuck-toilet-handle-2718758

12 hours ago The handle can also slack due to a disconnection or unfastened chain inside the toilet tank. You can simply fix this problem by replacing the handle, reconnecting the chain to the handle so it …

5.Toilet Handle Loose - Troubleshooting & How to Fix

Url:https://toiletseek.com/how-to-fix-loose-toilet-handle/

11 hours ago 1. Remove the old toilet handle. Remove the toilet handle and the lever arm, so you can take them with you to the home improvement store. This plastic nut is a reverse thread, so usually, …

6.How to Flush a Toilet when the Handle is Broken

Url:https://amarcoplumbing.com/flush-toilet-handle-broken/

28 hours ago

7.How to Replace a Toilet Handle: 11 Steps (with Pictures …

Url:https://www.wikihow.com/Replace-a-Toilet-Handle

23 hours ago

8.How to fix a Toilet Handle that Stays Down, Doesn’t …

Url:https://toiletseek.com/fix-toilet-handle-stays-down/

2 hours ago

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9