how do you fix a hole in a door hinge

1. Plug holes with golf tees if the holes are big enough. Remove the loose screws and the hinge. ...
2. Fill holes with toothpicks or matches to provide added grip for screws. Unscrew the loose screws and remove the hinge from on top of the stripped holes.
3. Put wood anchors into stripped holes so the screws fit tightly. Buy some plastic, cone-shaped wood anchors that match the diameter of the hinge screws.
4. Fill loose holes with cyanoacrylate glue and reinsert the screws for a quick fix. ...
5. Use longer screws to secure a hinge to loose holes. Remove any loose screws from the hinge using a screwdriver or drill.

Full Answer

How to quickly fix a loose door hinge?

Feb 19, 2019 · Fix it the RIGHT WAY, not the WRONG WAY! The wrong way is a temporary fix...Not cool!If interested in purchasing this product, shop our amazon associate lin...

How do you fix a broken door hinge?

Jan 06, 2014 · A simple method of using golf tees to fix holes that have been stripped out and are to big so the screws will not tighten up the hinge to the door or jamb. ...

How to hide old door handle holes?

If you have a centering hinge drill use the hinge as a template and the finish repair will be better than new and last for years. Another hint is to use a long screw in one of the holes in the top most hinge long enough to penetrate the stud. After time the weight of the door will pull on the hinge and cause the door not to hang straight.

How to fit a flush hinge on a door?

May 08, 2020 · This is how to fix damaged cabinet door hinges step by step. This is a very common problem with an easy soloution. These hinges are commonly found all around...

How do you repair a hole in a door hinge?

How do you fill holes in left hinges?

How do you fix a screw hole in a wooden door?

How do you fix a broken wood door hinge?

How do I fill a hole in a door?

How do you fix a broken side of a door hinge?

What is the best wood filler for screw holes?

Can wood filler hold a screw?

How do you repair holes in wood?

How do you use wood filler on a door?

How do you fix a splinter in a door jamb?

Step 1: What You'll Need

You'll need: A drill A wooden dowel (I used a 4ft long 3/8" poplar dowel - $0.84 at a local store) A saw of some kind if you need to cut your dowel A 3/8" drill bit (I used a Forstner bit) Wood glue Shop brush A smaller drill bit (to drill new pilot holes after you've patched the old holes) A screwdriver The dowel I bought was 48" long, so I cut off three pieces that were around 1.5" long.

Step 3: Dry Fit Your Dowels to Make Sure They Fit

I dry fitted the dowels to make sure the holes fit right before I added glue to the mix. They fit perfectly. Snug, but not overly tight. In other words, they didn't wiggle around, but there's room for glue in there. Don't push them in all the way, or you won't get them back out to add glue.

Step 4: Add Glue

Add glue to the holes. Use your shop brush to spread the glue evenly all around the insides of the holes. Add glue to the dowels, using the brush to spread it evenly around the surface.

Step 5: Insert Dowels

Push your dowels in, just until they are flush with the surface of the wood. You don't want them to be inset, or sticking out too far. They need to be flush so your hinge sits in the opening right and the screws have plenty of wood to hold onto once you reattach them. After pushing in you'll have a gluey mess left over.

Step 6: The Way-aiting Is the Hardest Part

At this point I read my glue bottle to see how long I have to wait before reattaching the hinge. It says not to stress the joint for 24 hours. Your glue might differ. Just read your bottle, chill out, and listen to some Tom Petty. Take photos of stuff and post it to Instructables to kill the time.

Step 7: Mark and Drill New Pilot Holes

Ok, so you've waited until your glue has fully cured, right? Me too. Now you either need to prop your door up so that it stands up correctly while you work on it, or it might be easier to have a helper hold it up for you if you have someone handy. Hold the hinge in place and mark the hole locations. Use your drill and a small drill bit to drill new pilot holes for your screws.

Step 8: Reattach the Screws

Using a screwdriver, reattach the screws. I'd probably recommend against a driver bit in your power drill, just to make sure you don't use too much force and strip the screws back out again. Test out the door, and enjoy pooping in private. See you next time, when Monkey Boy and Disaster Girl strike again!

How to unscrew a hinge plate?

Remove the loose screws and the hinge plate with a drill or screwdriver. Use a screwdriver or electric drill to unscrew the loose screws all the way. Set the screws aside and swing the hinge plate away so it’s not covering the loose holes.

How to get paint off a hinge?

If there is paint over the hinge, you can slice around it carefully with a utility knife or box cutter to free it so you can swing the plate away.

How to make a dowel with carpenter's glue?

Coat a 1 in (2.5 cm) long, 3⁄8 in (0.95 cm) diameter dowel in carpenter’s glue. Squeeze a drop of carpenter’s glue out onto the side of the piece of wooden dowel. Use your fingers or a scrap piece of dowel to spread the carpenter’s glue up and down the sides.

How to fix a hole in a golf tee?

Plug holes with golf tees if the holes are big enough. Remove the loose screws and the hinge. Dip the tip of a golf tee into carpenter’s glue, tap it into a loose hole using a hammer, then snap off the excess wood sticking out of the hole. Reattach the hinge by driving screws through its holes into the golf tees after the glue is dry.

What glue holds dowels in place?

The carpenter’s glue will hold the dowel in place inside a stripped hole.

How to hold wooden dowels steady?

If you use a handheld saw, clamp the wooden dowel to a workbench or put it in a vise to hold it steady while you cut the pieces.

How to cut a 3/8" dowel?

Measure and mark 1 in (2.5 cm) long sections along an entire piece of dowel. Use a hand saw or any type of power saw you have available to cut the pieces.

How to tighten a stripped hinge?

How to Tighten Stripped Hinge Screws. Open the door wide and insert a wedge under the bottom outside corner to level it. Remove the screws that hold the loose hinge leaf to the door jamb. (If the hinge and jamb are painted, cut the paint around the leaf with a utility knife.) Swing the leaf away from the jamb.

What to do if your door sags?

If a door sags because the hinge holes are stripped, you can use dowels to save the day.

Why does my door hang crooked?

A loose butt hinge will cause a door to hang crooked and stick. Sometimes retightening the hinge screws is all it takes to fix the problem. But if the screws can't be tightened because the holes are stripped, try this:

How long to wait to reposition hinge leaf?

Wait at least an hour. Then reposition the hinge leaf and bore 1/8-inch-diameter pilot holes.

How to level a door with a wedge?

Open the door wide and insert a wedge under the bottom outside corner to level it.

How to get a hinge pin out of a hinge?

If you find the hinge pin stuck in place due to corrosion, you can try tapping it from under with the help of an 8D nail approximately 2.5 inches long or one of a similar size. You can force the pin free by positioning the nail at the bottom of it and gently tapping the nail head with a hammer.

What tool to use to fix a door that is stuck?

You could also use our Hinge Tweaker tools for this issue. They provide an easy and stepwise guided process for eliminating jamming, rubbing, sticking or scratched doors. We have engineered these tools to heal you tackle problems such as misalignment of doors: sticking or sagging.

How to get WD40 out of hinge pin?

You can bring each hinge pin loose by tapping gently with a mallet or hammer on them. Once the pin comes loose, lift it out, coat it with the lubricant and put it back in. Also, our cool tool called the Hinge Doctor can really help direct that WD40 if you choose not to grease up your hinges.

What is hinge tweaker?

The hinge tweaker re-bends the hinge to tweak it and thereby correcting the misalignment. The hardware and door industry refers to this re-bending technique as “closing the gap” or “closing the swedging of a hinge.” Your door will realign after you re-bend the hinge.

What is a longer hinge screw?

Our longer hinge screws have a special design that keeps your hinges and, consequentially, all your doors right in place and with proper alignment. These screws are so long they pose no difficulty in going all the way inside the door jam and ensure the door remains firmly in place.

What is hinge shim?

The hinge shim's slight wedge shape allows additional control when you’re installing or door or merely correcting a gap. They are ideal for steel doors and jambs too. If your residential property is an older one, there are high chances that most of the doors in your house have stayed latched in for a long time.

How to get pins off of garage door?

You may have to make use of the tools in your garage to pry the hinges and pins loose. You can use the head of a screwdriver if you have a nickel-plated or brass hinge at home. Wedge the head under the hinge pin’s head and softly tap with a hammer on the handle of the screwdriver. This will help you push the pin upwards and pry it free from the hinge.

How to fill a hole in a drywall wall?

Fill the hole with expanding foam insulation. This material comes in a large aerosol can with a long plastic applicator tip. Squirt a generous amount into the hole, so that the foam expands to fill the hollow space behind the hole. Allow the foam to dry. This will take several hours, so it’s best to let it dry overnight.

How to put spackle over a hole?

Use a putty knife to apply a layer of spackle over the hole. Work in long, smooth strokes to apply the putty as smoothly as possible. Allow the spackle to dry once you’ve applied it. Give it about an hour.

How to sand a spackle hole?

Sand the hole once the putty has dried. Take a sheet of sandpaper and rub it over the dried spackle until it’s completely flat and smooth. You can use 100-grit sandpaper for this task as well. You should use a different sheet from the one you used to sand down the filler, though.

How long does it take to fill a hole in a car?

The entire process should take only 1 or 2 hours, plus drying times for auto-body filler and spackle. Steps.

How to make a door seal with auto body filler?

Mix auto-body filler and a hardener catalyst at a 2:1 ratio. Scoop or squeeze an auto-body filler out of its container and into a disposable bowl or any sort of plastic tray. Then squeeze in half as much hardener catalyst. This material will quickly harden and cover the outside of the door hole. These are both thick, putty-like liquids; use a popsi cle stick to stir them until the substances are fully blended.

What is hollow core door?

Hollow-core doors are common in the interiors of houses and apartments. These relatively flimsy doors can be damaged easily. If you or someone you live with has accidentally knocked a hole in a hollow door, you can fix it with materials available at your local hardware store.

How to find a good match for a door?

In order to find a good match, visit a paint store, bring home multiple swatches, and find the color closest to that of your door.