How do you troubleshoot a Homelite chainsaw? Basic troubleshooting tips: 1- Make sure the chain moves freely over the bar. 2- Replace stale gasoline with fresh gas. 3- make sure the run switch is in the on position. 4- Test for spark. 5- Remove the carburetor for cleaning and gasket replacement.
Full Answer
How do you adjust the oil on a Homelite chainsaw?
Check the oil output adjustment screw on Homelite models that have one. The screw is located on the bottom of the chain saw and increases or decreases the oil output in relation to the adjustment. Before adjustment, start the chain saw and allow the engine to run for a couple of minutes.
Are Homelite chainsaws still in use?
The Homelite Corporation was a pioneer in the early home use power equipment market and their professional chainsaws were regarded as the best for several decades. Many are still in use today, however, in being out of production, reliable information is becoming harder to find.
How do you lubricate a chainsaw chain tensioner?
Tighten the yellow chain tensioner knob fully to hold the adjustment. Fill the bar chain oil reservoir to the fill line with oil before starting the chain saw and allow it to run a few moments to distribute the lubrication along the chain and bar.
What is the horsepower of a Homelite 150 chainsaw?
The Homelite 150 model chainsaw with automatic oiler was produced for a single year, 1986, and has an engine displacement of 43.3 cc. This translates into roughly 2.95 horsepower at 8000 RPM, according to Homelite.
How to fill a Homelite XL chain saw?
What to do if you have too much oil on a chainsaw?
How to remove a chain from a saw?
How to loosen a washer?
How to unclog a sprocket?
Where is the oil adjustment screw on a chainsaw?
Can you use a chainsaw without lubrication?
See 4 more
About this website
How do you fix a Homelite chainsaw that won't start?
If the ignition coil is defective, the engine may not start. Before you replace the ignition coil, make sure that the spark plug is in working condition. If you have confirmed that the spark plug is not defective, test the ignition coil using an ignition coil tester. If the ignition coil is defective, replace it.
What causes a chainsaw to stop working?
Once gasoline oxidizes, varnish, gums and other insoluble debris form, which can plug the tiny fuel passages in a chainsaw carburetor. It doesn't take much to interfere with proper fuel flow, causing chainsaw starting problems or rough running once you get it going.
Why is my Homelite chainsaw not cutting?
Common solutions for: Homelite Chainsaw not cutting The most common cause of a chainsaw that won't cut properly is a dull cutting chain. Try sharpening or replacing the chain. The chain may not have the proper amount of tension. If the adjustment screw is too loose, the chain may not make good contact with the wood.
What's the mixture on a Homelite chainsaw?
The recommended fuel mixture is a 50-to-1 ratio of unleaded gasoline and two-cycle engine oil, and the manufacturer recommends the use of a two-cycle oil that contains fuel stabilizer to keep the mixture fresh if you are not using it immediately.
How do I get my chainsaw to run again?
If your chainsaw won't start after being unused for a long time, the carburetor may be clogged. As the fuel becomes old, it becomes sticky and can clog the carburetor. If the carburetor is only slightly clogged, simply remove it and clean it before putting it back in the chainsaw after it has fully dried.
How do I know if my chainsaw spark plug is bad?
What Does a Bad Spark Plug Look Like and What Makes It Look That Way?Black, chunky carbon buildup spanning the gap between the sparking end of the plug and the hook-shaped metal piece overhanging the end.Dark carbon residue built up on the ends but not spanning the gap.More items...•
Why is my chainsaw smoking and not cutting?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
What could be the problem when chainsaw getting fuel but not starting?
1:162:20Top Reasons Chainsaw Won't Start — Chainsaw TroubleshootingYouTubeStart of suggested clipEnd of suggested clipOld or bad fuel can also create a clog in the fuel filter which can prevent the chainsaw fromMoreOld or bad fuel can also create a clog in the fuel filter which can prevent the chainsaw from starting we recommend replacing the filter with a new. One. If the starters recoil spring is broken the
Why does my chainsaw bog out when I give it gas?
The main reason for an ECHO chainsaw to bog down is the dirty spark arrestor. It should be the first thing to check and clean. After this, check the air filter and carburetor for dirt and debris.
Can I use 50 to 1 mix in a chainsaw?
Most modern chainsaws, string trimmers, leaf blowers and other small-engine two-stroke equipment recommend a 50:1 oil mix ratio, but some recommend 40:1 and older two-stroke equipment might even call for 32:1.
What's the mixture to 50 to 1?
0:071:0250:1 Fuel to oil ratio easy way to calculate - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst of all what we're going to do is going to multiply by two and then you're going to add a zeroMoreFirst of all what we're going to do is going to multiply by two and then you're going to add a zero to the end of that number so let's use 35 liters as an example solve 35 liters times two equals 70
How do you adjust a Homelite carburetor?
1:053:54HOW TO ADJUST the Carburetor on the Homelite Timberman 45 ...YouTubeStart of suggested clipEnd of suggested clipIf it runs lean I'm going to unscrew the L screw. If it runs too rich I'm going to screw it inMoreIf it runs lean I'm going to unscrew the L screw. If it runs too rich I'm going to screw it in slowly. All at the same time listening to the engine. To hear it run at its.
Why does my chainsaw cut out when I give it gas?
The reason for this is usually some clogging in the carburetor or in some other area that resists the flow of air and fuel. To overcome this you should check the filters and if there is any thick oil deposited on the surface. Clean the filters and oil tank and that's all. Your chainsaw would not die now.
Why does my chainsaw stop running after a few minutes?
When your chainsaw starts fine but then stops, the reason is often that the engine does not receive the correct fuel-air mixture. The most common reasons for this are a blockage in fuel lines, a clogged or faulty carburetor, a dirty air filter, or a faulty spark plug.
How do you know if your chainsaw clutch is bad?
How do I know if the clutch on my chain saw is bad? If the chain continues to turn or if the chain slips under load you should stop using the equipment immediately and have it evaluated by a local authorized service center.
What happens when a chainsaw overheats?
0:115:28My chainsaw is smoking and overheating - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd if you leave that long enough it will overheat the engine and the Rings will stick in the pistonMoreAnd if you leave that long enough it will overheat the engine and the Rings will stick in the piston. And you won't have any compression. And you pretty well destroyed your motor.
Homelite XL chainsaw oiler problems - DoItYourself.com
Outdoor Gasoline and Electric Powered Equipment and Small Engines - Homelite XL chainsaw oiler problems - My old Homelite XL chainsaw is not using sufficient chain oil. I always use Oregon oil and have stripped the oil tank tube and cleaned them but it is still not using enough and overheats drastically stopping after
Vintage Homelite XL-12 Chainsaw Manual Oiler Repair!! - YouTube
I decided to do a quick video on an o-ring change with this Chainsaw. It is a very easy repair that anyone can do. https://www.instagram.com/vintagechainsaws...
Parts Lookup and OEM Diagrams | PartsTree
Repair parts lookup and OEM diagrams for outdoor equipment like Toro lawn mowers, Cub Cadet tractors, Husqvarna chainsaws, Echo trimmers, Briggs engines.
Home lite XL-12 manual oiler | -- HOUSE OF -- HOMELITE - ProBoards
Oil just spitting out ,I put new o rings on pump but it does not seem to pump well.cleaned out oil tank and put in fresh oil did not help.took apart the inlet ball check ( mistake outside and on dirt drive but everything was found - twice and reinstalled!)this is a great little saw never have many problems and it starts easy,I am impressed but the chain needs oil.
How to fill a Homelite XL chain saw?
1. Check the oil reservoir to ensure that there is oil in the tank that feeds the automatic oiler. If the tank is empty or low, fill the tank with Homelite Bar and Chain Oil for the best results. Fill only to the fill line. The Homelite XL chain saw is designed to use one tank of oil per each tank of fuel. Fill the oil reservoir each time you fill ...
What to do if you have too much oil on a chainsaw?
When you notice too much or too little oil on the chain, stop cutting immediately, and diagnose and fix the problem. Cutting wood with too little lubrication on the chain saw chain can be detrimental to the saw and can pose safety risks to you.
How to remove a chain from a saw?
Push the yellow chain tensioner knob in and turn it counterclockwise to release and remove the chain cover, and gain access to the bar and chain. Push the guide bar toward the saw, and remove it and the chain. Clean the groove and channel with a stiff-bristled brush.
How to loosen a washer?
Rotate the clutch clockwise with a clutch tool to loosen it from its position. Unscrew the clutch the rest of the way by hand and pull it free from the machine. Tilt the machine toward you so the large washer falls out onto the work surface.
How to unclog a sprocket?
If the sprocket is immobilized, lubricate it until it is mobile and unclog the hole by clearing it out with the end of a straightened paperclip.
Where is the oil adjustment screw on a chainsaw?
The screw is located on the bottom of the chain saw and increases or decreases the oil output in relation to the adjustment. Before adjustment, start the chain saw and allow the engine to run for a couple of minutes.
Can you use a chainsaw without lubrication?
Avoid operating the chain saw without lubrication. Doing so can quickly cause irreparable damage to the chain saw, and increases the risk that you may be injured from kickback when the blade hesitates while cutting through wood and is forced back toward you at a high rate of speed.
Who bought out Homelite chainsaw?
The Homelite Corporation, manufacturer of popular chainsaws, was first bought out by Textron in the early 1950's. Subsequently, the brand was sold to John Deere in 1994 and then to TechTronics Industries in 2001.
What type of oil does a Homelite chainsaw use?
Homelite operator manuals recommend using Homelite brand chain oil or clean SAE-30 to oil the chain, however, environmentally conscious operators report having good results with bio-degradable vegetable based oils that won't pollute or leave toxic residue behind like motor oil does.
Are Homelite chainsaws any good?
They do a good job on light to medium jobs and are perfect for home use. As far as newer models go, Stihl and Husqvarna chainsaws dominate sales like Homelite once did.
What year did Homelite go out of business?
The Homelite Corporation, maker of popular chainsaws for the home market, ceased being an independent company in 1954 when it was acquired by Textron. The Homelite brand was next sold to John Deere in 1994 and is still in production today by it's most recent owner, Techtronic Industries.
What year was the Homelite 330 chainsaw made?
HOMELITE-TEXTRON of PORT CHESTER, NEW YORK, USA, first made the Homelite 330 model chainsaw in 1981. It featured a 54cc engine, a powerhead that weighed 12 lbs. 8 oz (without bar and chain) and an automatic oiler. The self-oiling feature proved popular among users used to controlling bar oiling chores manually.
How old is a Homelite XL 12 chainsaw?
In 2021 the oldest Homelite XL 12 chainsaw would be 57 years old and the newest would be 33 years old. The Homelite XL 12 model enjoyed a 24 year production run in Canada and the US. Older XL-12s are often blue and white in color while newer ones are typically Homelite red.
Is Homelite made in China?
Currently yes, since 2001 Homelite chainsaws are manufactured by TechTronics Industries based in Hong Kong. Prior to 2001 Homelite chainsaws were manufactured in North America by Homelite Corporation (pre-1954), Textron (1954-1994) and John Deere (1994-2001).
Most Common Problems
It could be the spark arrestor or the clutch pads, the spark plug or the carburetor. Right now, you don't know. But after you look at the array of problems below, pick the right one and work down the list of possible causes, you will.
The Right Parts for the Job
We carry more than 4 million parts from over 175 major brands, so chances are, we've got the part you need.
How to fill a Homelite XL chain saw?
1. Check the oil reservoir to ensure that there is oil in the tank that feeds the automatic oiler. If the tank is empty or low, fill the tank with Homelite Bar and Chain Oil for the best results. Fill only to the fill line. The Homelite XL chain saw is designed to use one tank of oil per each tank of fuel. Fill the oil reservoir each time you fill ...
What to do if you have too much oil on a chainsaw?
When you notice too much or too little oil on the chain, stop cutting immediately, and diagnose and fix the problem. Cutting wood with too little lubrication on the chain saw chain can be detrimental to the saw and can pose safety risks to you.
How to remove a chain from a saw?
Push the yellow chain tensioner knob in and turn it counterclockwise to release and remove the chain cover, and gain access to the bar and chain. Push the guide bar toward the saw, and remove it and the chain. Clean the groove and channel with a stiff-bristled brush.
How to loosen a washer?
Rotate the clutch clockwise with a clutch tool to loosen it from its position. Unscrew the clutch the rest of the way by hand and pull it free from the machine. Tilt the machine toward you so the large washer falls out onto the work surface.
How to unclog a sprocket?
If the sprocket is immobilized, lubricate it until it is mobile and unclog the hole by clearing it out with the end of a straightened paperclip.
Where is the oil adjustment screw on a chainsaw?
The screw is located on the bottom of the chain saw and increases or decreases the oil output in relation to the adjustment. Before adjustment, start the chain saw and allow the engine to run for a couple of minutes.
Can you use a chainsaw without lubrication?
Avoid operating the chain saw without lubrication. Doing so can quickly cause irreparable damage to the chain saw, and increases the risk that you may be injured from kickback when the blade hesitates while cutting through wood and is forced back toward you at a high rate of speed.
