Chevrolet Silverado: Why Won't My Tailgate Open/Close?
- Step 1 – Lubricate the latches They might be corroding. Pry off the tailgate cover and check the entire area for corrosion, dirt and other debris. ...
- Step 2 – Pry off the door trim You might need to repair the latch to your tailgate. ...
- Step 3 – Install a brand new handle The one you have might be too defective to repair. ...
Full Answer
See more
How do you fix a tailgate that won't latch?
How to Fix a Tailgate That Won't LatchTest the Latches. Press the latch with a Phillips screwdriver and see if it latches. ... Test the Handle. Remove the outer trim piece from the tailgate handle with a trim tool. ... Test the Latch Pin. See if the striker pin or latch pin needs to be adjusted.
How much does it cost to fix a tailgate latch?
The average cost for tailgate lock cylinder replacement is between $99 and $110. Labor costs are estimated between $40 and $50 while parts are priced at $59. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location. Related repairs may also be needed.
How do you unjam a tailgate on a truck?
2:194:01How To Open A Stuck Tailgate - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd i'm just going to bang it toward hammering towards the left side of the truck toward the middleMoreAnd i'm just going to bang it toward hammering towards the left side of the truck toward the middle and that will pull it open pull the pull rod which will release the latch. On.
How do you tighten a tailgate on a Chevy Silverado?
TAILGATE ADJUSTMENT TIPSLoosen both pickup box side hinge bolts (1) on the right and left side.Install shims (2) on both sides, if needed.Hand-tighten the bolts (1) on each side.Close the tailgate and adjust for fit and flushness, both up-down and fore-aft.Open the tailgate and tighten the bolts.
How do you open a broken tailgate?
0:421:25How to open a broken tailgate - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then yeah the next step is get a screwdriver. And all you have to do is push down on this rightMoreAnd then yeah the next step is get a screwdriver. And all you have to do is push down on this right here. And there you go you can drop the tailgate lift the tailgate and load your dogs.
How long does it take to install a tailgate?
One (1) helper to assist with the installation. 4 or 5 chains at least 10 ft long (10 to 20 ft preferred)...Approximate Installation Time:Articulated Tailgate:35 - 50 man hours +/-Outriggerless Tailgate:45 - 60 man hours +/-Ultra-High Tailgate:45 - 60 man hours +/-2 more rows
Why is my tailgate not closing?
0:146:33Tailgate Won't Stay Shut? How to Fix a Stubborn Truck Tailgate! - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhen you notice the tailgates not closing the first thing you want to look at is see if there's anyMoreWhen you notice the tailgates not closing the first thing you want to look at is see if there's any debris in the way if there's anything left that's going to cause the gate to not close properly.
Why wont my liftgate go down?
The most common liftgate issues can be traced back to the motor or motor start solenoid. If you hear a clicking noise when the switch is activated, more than likely you have a bad solenoid. Using a small jumper cable, bypass the solenoid by putting direct power to the motor to see if it will run.
How does a tailgate mechanism work?
Using a push-pull mechanism, a tailgate actuator relies on the power of an electric solenoid to open the tailgate. Connected to the latch mechanism located inside of the tailgate assembly, the tailgate is opened when the tailgate actuator is activated and pulls the release latch via a chain or metal rod.
What is EZ lift tailgate on Chevrolet?
EZ Lift-and-Lower tailgate is a General Motors convenience technology that makes using a pickup truck's tailgate easier and more convenient.
How do you lubricate a tailgate latch?
Start by removing the access panel on the tailgate. (If you have a bed liner, you'll have to remove the tailgate section before you get to the access panel.) Once the cover's off, use compressed air to blow off the lock mechanism. Then apply a liberal coat of lithium grease to the cam/lever area and all pivot points.
How do you hold a tailgate up?
1:003:52How to Secure the Tailgate of Your Pickup Truck When Hauling Two ...YouTubeStart of suggested clipEnd of suggested clipAnd just clip it. In. And tighten it. You can tighten this against the rear tires. And it's alsoMoreAnd just clip it. In. And tighten it. You can tighten this against the rear tires. And it's also going to use the spring on the foot peg to help keep it secure.
How long does it take to replace a trunk latch?
The cost to replace a trunk latch release cable is $140-$175 at our garage, and it only takes about an hour at most.
How much does it cost to replace a tailgate?
A new tailgate can cost you anywhere from $100 to $300 on parts alone. Labor can set you back another $40 to $70, depending on the rates in your area.
What is a tailgate latch?
Ideal for sealing dump body and dump trailer tailgates against the body of the vehicle. Helps prevent unintentional opening of the tailgate. Keeps mulch, dirt, loose stone, or any other messy material inside the vehicle. Available in steel, stainless steel, and aluminum.
What is a tailgate on a car?
countable noun. A tailgate is a door at the back of a truck or car, that is hinged at the bottom so that it opens downwards.
What to do if your latch is damaged?
Replace the damaged clip, which connects the latch to the bar.
What to do when parts do not need replacement?
Lubricate all of the parts that do not appear to need a new replacement.
How to lock a clip on a sleeve?
Pry the tab open using a flat head screwdriver, and then flip the clip upward and lock it in place for a secure hold.
How to cut costs on replacement parts?
To cut costs, purchase your replacement online and then have a mechanic complete the actual installation.
What happens if the door trim is off?
Once the door trim is off, check that the bar that actuates the latch on the passenger side of the truck is attached and working properly. Do the same for the second bar, which, of course, actuates the latch on the driver side of the truck. It is common for one of the bars to disconnect, causing your tailgate to fail.
How to fix a broken tailgate handle?
The actual broken tailgate handle repair is easy, just three bolts and a couple of plastic clips that hold the rods that operate the latches hold the handle in place. We unbolted the handle and popped the clips off. This allows us to replace the handle, but what about the latches? If you don’t take care of the latches now, the new handle will just break again down the road.
How many bolts are there in a tailgate latch?
There are two bolts holding the latches in place on each side. Only remove one at a time, as the tailgate cable has to be removed as well.
When reinstalling latches, do you have to make sure the rod goes above the recess?
When the latches are reinstalled, you have to make sure the rod goes above the recess for the handle, otherwise you will have to pull it out and reinstall it.
Can a truck's tailgate handle break?
This can happen on any truck, but it doesn’t have to. The tailgate handles is not the issue here, it is actually the latches themselves. There are two latches, one on either side of the tailgate. Over time, these latches get coated with dirt and rust. When the lubrication is gone and the latch sticks, the increased effort required to open the tail gate stresses the cast iron arms on the handle. Put too much stress on these arms, and they break, leaving you with a busted tailgate.
