How to Fix a Washer that Won’t Spin
- 1. Level Up the Washer You need to know that the washer tub is usually suspended inside the drum in order for it to spin freely. ...
- 2. Balance the Load ...
- 3. Reset the Motor ...
- 4. Check the Lid Switch ...
- 5. Unclog a Washer that Won’t Drain ...
- 6. Replace Worn Out Motor Carbon Brushes ...
- 7. Realign or Replace the Drive Belt ...
- 8. Inspect the Motor Coupler ...
- Lighten the load inside the washer. ...
- Rebalance the load in the washing machine. ...
- Check or repair the washing machine drain hose. ...
- Check for blown fuses. ...
- Check the washing machine lid safety switch. ...
- Replace the drive belt in your washing machine. ...
- Replace the motor in your washing machine.
How to fix a washing machine that does not spin?
- Unplug the washing machine and locate the lid switch.
- Remove the lid switch (you may need to open the washing machine cabinet to access the full switch).
- Set your multimeter to Rx1 and touch both probes to the switch terminals. You should get a reading of zero, which indicates continuity. ...
Why is my washer not spinning all the water out?
| What You Need to Know
- Check Your Machine’s Power Supply. Perhaps one of the easiest answers to the question, “Why is my washer not draining or spinning?” is in its power source.
- Reset Your Machine. If your machine has this function, try performing a master reset on it. ...
- Check the Machine’s Position on the Floor. ...
- Rebalance the Washer’s Load. ...
- Inspect the Lid Switch. ...
Why is my washing machine not spinning?
You can find out if the pump is the problem by:
- Unplug the washing machine. ...
- Identify the pump and see if it turns freely when you loosen the tension from the pump belt that is wrapped around it.
- If the pump belt is worn or broken, that is likely the extent of the problem. ...
- If the pump does not turn freely or will not turn at all, you will need to have the pump removed and replaced.
How to fix a washer that will not agitate?
Washer Will Not Spin and/or Agitate
- Too Large of Loads. A washing machine will become unbalanced if there are too many clothes being washed in the same load.
- Switches and Settings. The lid switch is located inside the cabinet near the door frame, and it's designed as a safety precaution to keep hands from entering a spinning washer ...
- Drain Pump. ...
- Belts. ...
- Motor. ...
Why won't my washer spin?
A motor that doesn’t run at all, despite good connections to the power source and breaker, could prevent a washer from spinning. Some motors contain carbon brushes that wear out over time, and those can be replaced inexpensively. However, the problem could be more extensive than a worn carbon brush, and it’s impossible to know without removing the motor and testing it. Even with the washer unplugged, induction-type motors that contain capacitors can give you quite an electric shock, so motor testing and repairs are best left to the pros.
Why is my washing machine spinning?
An unbalanced load of laundry is one of the most common causes of an inadequate spin cycle. Sometimes clothing can settle on one side of the drum, throwing off the motion of the washing machine. (This happens most often when washing large and heavy items like comforters or heavy coats.) Moreover, some newer machines won’t reach high speeds with off-balanced loads, which leaves clothes dripping wet. If you suspect a distribution problem, try rearranging your clumped-up wet laundry and running the spin cycle again.
How to check if a washer coupler is broken?
To determine whether the motor coupler (a small rubber and plastic connector piece located between the washer’s motor and its transmission) has broken, conduct this simple test: Set the dial on your washer to a wash cycle and turn it on, allowing the drum to fill with water. When the water reaches the fill level, agitation should begin. If you hear the motor kick on but the center agitator does not move, your machine needs a new coupler. While a replacement is in the ballpark of a mere $20, this fix is only DIY-friendly for those who are skilled in small motor repair.
Why does my washer agitate?
A broken drive belt, or one that has slipped off the pulley wheel, can cause the washer to agitate during the wash cycle and yet—despite the noise of the motor running—the drum remain still during the spin cycle. To determine if this is the case, remove the back of the washer and visually check to see if the belt is still on the pulley. If not, you may need to replace the drive belt. Be sure to purchase one that’s made specifically for your brand and model of washer.
What does a small protrusion on the underside of the washer do?
In a top-loading washer, a small protrusion on the underside of the lid depresses a switch when you close the lid, serving as a safety precaution to detect when the lid is closed. If the protrusion has bent out of shape, it may not trigger the switch as intended.
Why does my washer leak?
Some washers feature electro-mechanical transmission shifters or clutches that, when worn out, can result in washing machine leaks. This issue also requires attention from a repairman.
How to test a spin cycle on a washer?
Test the theory by opening the lid, selecting the spin cycle on your washer, and then manually depressing the switch with a finger. If the machine starts spinning normally, simply re-bend the protrusion so it triggers the spin switch properly.
1. Level Up the Washer
You need to know that the washer tub is usually suspended inside the drum in order for it to spin freely. Why is this a problem though?
2. Balance the Load
Washing a single or just 2 pieces of laundry causes an imbalance inside the drum which stresses the drum support system as well as other parts. This causes the washer to either spin slowly or not spin at all.
3. Reset the Motor
This will not work on all washing machines but it will do on others ( top-loading washers with a direct-drive system, which does not need a transmission system to spin). Resetting a washer motor will not even take you a minute to complete.
4. Check the Lid Switch
If your top-loading washer is not spinning, you could be dealing with a faulty lid switch. A washing machine with a broken or stuck lid switch will not spin or even drain.
6. Replace Worn Out Motor Carbon Brushes
If your washer is not spinning but you can hear the motor kick in amid a cranking noise then the motor carbon brushes are worn out and will need to be replaced. To do this, you will need to first remove the washer’s back panel to access and remove the motor.
7. Realign or Replace the Drive Belt
A washing machine drive belt is responsible for transferring motion from the motor to the drum. The belt is hooked on the motor as well as drum pulley.
8. Inspect the Motor Coupler
A motor coupler is a small plastic and rubber piece that connects the motor and the washer transmission. If it is broken, you will hear an unusual noise when you start the washer.
A Faulty Lid Switch
Most modern washing machines are equipped with a lid switch. The lid switch is responsible for stopping the spin cycle when the lid of the washing machine is opened. It also restarts the spin cycle when the lid of the washing machine is closed.
A Bad Drive Belt
Another reason why your washing machine may be failing to spin could be because of a bad drive belt.
A Faulty Drive Motor
If it is the case that your washing machine fills up with water and empties out normally, but the wash tub does not turn at all, there could be a problem with the motor which turns the drum.
Faulty Or Worn Out Clutch Assembly
A clutch assembly is used in some washers to connect the transmission input shaft to the wash basket drive shaft when the water spins.
Faulty Drain Pump
Most washing machines will only start a spin cycle after all the water from the wash cycle has been completely drained out.
Unbalanced Load
If your washing machine moves slowly in the spin cycle, this could be due to unbalanced load in the machine.
How to get spade connector back?
Use a pair of pliers to pull back the spade connector that hooks to the brush. Tilt the old brush first to the left and up, and then to the right to release it from its compartment in the motor.
How to change a brush on a motor?
Tilt the old brush first to the left and up, and then to the right to release it from its compartment in the motor. Next, insert the new brushes. The heads of the new brushes are significantly longer than the old ones. Place the new brush in the slot the old one came out.
How long does it take for a Bosch brush to wear out?
Bosch is a reputable manufacturer famed for the quality of its products. However, motor brushes can wear out after around five or six years of regular use. When that happens, they can no longer deliver the power required to spin the drum, necessitating clothes washer repair.
Can a Bosch washing machine drain?
Bosch washing machines can also sometimes experience a drain pump blockage.
Do you have to replace a Bosch washer if it is not working?
Fortunately, you don’t always have to replace the entire unit if your washer is not working. In many cases, simple fixes will get the machine up and running again.
Why won't my washer spin?
If your washer does not spin you should inspect the drive belt for signs of overheating or excessive wear. Before replacing a damaged belt, you should verify that any belt tensioning device such as an idler pulley or motor glide is operating properly and moves freely.
How to test a washing machine lid switch?
How to test the lid switch in a washing machine with a multi-meter: Because you will be handling electrical components, ensure that you have unplugged your appliance before beginning. Locate the lid switch on your appliance. Remove any parts of the cabinet you need to in order to have full access to the switch.
How to inspect a washer door lock?
How to inspect the door lock on a washing machine: Unplug the appliance before beginning. The door lock is usually found along the frame of the washing machine, under the lid. Begin by cleaning the area to remove any films that may have developed. If this does not resolve the issue, remove the door lock to inspect it for any signs of wear, damage, ...
What is a door lock on a washing machine?
The door lock, also known as the interlock, is a safety mechanism installed on front-loading washing machines, and some top load washers, which prevents the door from being opened while the machine is in operation. The system consists of the locking mechanism on the machine and the door strike on the door. The locking mechanism also contains a switch that will indicate to the control board or timer, when the door is locked and therefore allow a spin cycle to operate. When the door lock fails, it may not lock the door, or the door lock switch might not engage and therefore not recognize that the door is locked and not allow the washer to agitate or spin. Some modern washers with a digital display may show a fault code as well. If your washing machine is displaying any of these symptoms or a door lock fault code has been confirmed, the door lock may need to be replaced.
Why does my washing machine make a noise?
Over time, the repeated friction of the clutch pads rubbing against the housing can cause the clutch to wear and create a scraping sound. A worn clutch can prevent your washing machine from spinning or may cause a slower spin speed which will leave your clothes wet after a cycle. Additional symptoms that the clutch may be causing your problems are brake dust or shavings found underneath the washing machine, a slight burning smell or a loud noise during the spin cycle.
Why is the lid switch on a top load washer important?
The lid switch on a top load washing machine is used as a safety device to prevent the motor circuit from operating when the lid is open. If the lid switch fails, the was her may not spin.
What is a top load washer?
Some top load washers use a direct drive motor coupling to transfer power from the motor to the transmission. The drive coupling connects the motor to the transmission and consists of two plastic drive forks with a rubber coupling between them. One of the drive forks is attached to the drive motor shaft and the other is attached to ...
