Using the Roadie Wrap
- 1 Untangle the line. Especially if your cable has been wrapped haphazardly, you'll need to undo any knots and tangles. ...
- 2 Wrap the cable one way. Hold the end in your hand. ...
- 3 Twist the cable the other way. Now, bring the cable around again. ...
- 4 Alternate back and forth. ...
- 5 Make each loop the same size. ...
- 6 Wrap a strap around the middle. ...
How do you wrap a power cord with wire?
Wrap the cable one way. Hold the end in your hand. Wrap the cord so it goes around your hand and comes back to the same place in your hand. Most people typically wrap a cord this way. Start with just one wrap. [2] Twist the cable the other way. Now, bring the cable around again.
How to fold a power cord in half?
First, make sure you get all the existing tangles and knots out of the power cord Next, fold your cord in half. If you have a very long power cord, you may have to fold it in half a second, or even third time.
How do you wrap a cable with a knot?
The Overhead Knot: Speaking of quick and dirty wraps, the overhead knot is a great example. Just wrap the cable back and forth until it's somewhat short, then start a simple knot up top and pull it through loosely. While this may cause kinks if you leave it too long, it's possibly the fastest method you've got at your disposal.
How to wrap a guitar cable properly?
Instead, it’s better to wrap the cable in a more gentle fashion, and here are some ways to do that. Perhaps the best way to wrap any cable is to use the “Roadie Wrap” method, named after the audio, video, and music industry where this type of cable wrap is used the most in order to make their expensive cables last as long as possible.
How to make a braided cable?
How to store cables?
How to wind up a cable?
Can you wrap cable without a binder?
Can you knot your mic cables?
Do you need to wrap cables?
See 3 more
About this website
How to make a braided cable?
Start with a single coil and just start looping one part through the middle and around the cable. You'll have a nice braid-like look when you're done and you can then unwind the cable, bit by bit, to lengthen it (as needed).
How to store cables?
You can just use tape. Coil your cable, then wrap a strip of tape around it backwards, so the sticky side touches your fingers and not the cable. Then wrap another pieces of tape around that with the sticky side facing in so no adhesive gets on you, the cable, or anything else. Now you've tightly bound your cord, and you can easily remove that binding with a quick pull.
How to wind up a cable?
Finally, thicker cables will have a natural coil/memory to them. If you follow that natural coil about as you wrap/wind your cables up, you'll have a easier time of organizing them. To wit, hold one end with your left hand, wind the cable with the right. As you wind them up, you will feel the cable wanting to wind one way (left or right). Resist the urge the fight that, instead, let that coil the way it wants to coil as you wrap. It'll make no.1 a lot easier in the long run.
Can you wrap cable without a binder?
The Binder Clip Method: Obviously you can't have a cable wrapping video without a binder clip. If you're short on time and have one around, you can employ the same methods as the overhead knot, but just secure the cable with a binder clip rather than tying a knot at all.
Can you knot your mic cables?
As a counter to No 3: I wouldn't really knot your cables, and they will eventually damage your cables if not done carefully, especially towards the connector side of things. If you have something that is self serviceable like audio cables (think larger mic/XLR and 1/4" TS/TRS connector types), this is less of an issue however. If you're coiling and uncoiling cables every other hour or what not, this will be an issue. Generally, I wouldn't knot my cables, and it may kink and data may not flow as fast. ;P
Do you need to wrap cables?
We've shown you all sorts of ways to wrangle your cables in the past, but often you need to wrap and unwrap them when on the go. These six methods will help you keep all your cords contained quickly in most any situation.
How to make a cable fit in the other way?
Twist the cable the other way. Now, bring the cable around again. However, instead of tucking the end on the outside as you did in the first loop, twist it towards the inside. Turn the hand holding the end of the cable so the cable fits into it the opposite way.
How to wrap a cable cord?
Untangle the line. Especially if your cable has been wrapped haphazardly, you'll need to undo any knots and tangles. As you work out the tangles, drop the cable on the floor in a big pile. Basically, you're making it easier to wrap up, as wrapping a cord from a tangled mess is nearly impossible. This process is known as flaking the line.
How to secure a cable?
Bundle and secure with a binder clip. Wrap the cable around itself until you have a bundle. Use a binder clip to secure the end of the cable to itself. If the binder clip is big enough, you can wrap it around the whole bundle.
How to make a cable stick to everything?
Wrap a piece of tape around it with the sticky part facing outside, and stick it to itself. Wrap another piece of tape on top of it, sticky side to sticky side , so the cable won't stick to everything. Use the shortening method. Create one loop around your hand.
How to keep a cable in place?
Keep going back and forth between wrapping it one way and wrapping it the other way. This process helps the cable lie flat when you set it down somewhere, and it helps keep it in place. Make each loop the same size. To keep the cable neat and tidy, try to match up the size of the loops as you wrap it around your hand.
How to keep cable wrapped without sticking?
Make each loop the same size. To keep the cable neat and tidy, try to match up the size of the loops as you wrap it around your hand. That way, it's easy to keep the cord wrapped without bits sticking out. ...
Step 1
First, make sure you get all the existing tangles and knots out of the power cord
Step 2
Next, fold your cord in half. If you have a very long power cord, you may have to fold it in half a second, or even third time. You want to end up with a 18"-24" length of cord. If you are wrapping a thinner power cord (like a hot glue gun or other home appliance cords) you can make your cord lenth smaller (somewhere between 8"-12")
Step 3
Next, you are going to make a basic overhand knot with the folded over cord lengths.
Step 5
And unlike these other examples, this method will not put unnecessary stress on your cable connection points and extend the life of your tools.
How to wrap a cable cord?from wikihow.com
Untangle the line. Especially if your cable has been wrapped haphazardly, you'll need to undo any knots and tangles. As you work out the tangles, drop the cable on the floor in a big pile. Basically, you're making it easier to wrap up, as wrapping a cord from a tangled mess is nearly impossible. This process is known as flaking the line.
How to keep a cable in place?from wikihow.com
Keep going back and forth between wrapping it one way and wrapping it the other way. This process helps the cable lie flat when you set it down somewhere, and it helps keep it in place. Make each loop the same size. To keep the cable neat and tidy, try to match up the size of the loops as you wrap it around your hand.
How to secure a cable?from wikihow.com
Bundle and secure with a binder clip. Wrap the cable around itself until you have a bundle. Use a binder clip to secure the end of the cable to itself. If the binder clip is big enough, you can wrap it around the whole bundle.
How to make a cable stick to everything?from wikihow.com
Wrap a piece of tape around it with the sticky part facing outside, and stick it to itself. Wrap another piece of tape on top of it, sticky side to sticky side , so the cable won't stick to everything. Use the shortening method. Create one loop around your hand.
How to keep cable wrapped without sticking?from wikihow.com
Make each loop the same size. To keep the cable neat and tidy, try to match up the size of the loops as you wrap it around your hand. That way, it's easy to keep the cord wrapped without bits sticking out. ...
How to store cords in drawers?from wikihow.com
Fold and tie your smaller cords with zip ties, twist ties, or rubber bands and store them flat in the drawers.
How to safely transport a cable?from wikihow.com
Loop loose cables on top of themselves 3-4 times to transport them safely. Coil a cable gently on top of itself 3-4 times, so it’s about 1/3 or 1/4 of its size, then tuck the ends under the loop to secure it. Don’t just squish a cable together and shove it in a bag or fold it tightly and tie the ends in a knot because this puts a lot of stress on the wires.
How to fold heavy paper?
Use professional folding machines available to fold heavy papers and cardstocks. Take the folding machine that folds the paper without decreasing the diameter of the paper much and without causing wrinkles on it.
What is bone folder?
Another option is to use a bone folder. It is a more suitable option and is mostly used for craft purposes. It is made up of plastic or bone and is used for marking purposes. Its usage is the same as that of a knife. Keep the ruler straight and make a mark with it.
How to draw a line perpendicular to a cardstock?
At the exact center of your cardstock paper, make a mark, and then draw a line perpendicular line to that with the help of a bone folder or a knife. It is helpful because it ensures the correct markings and measurements.
Can you fold cardstock paper with a Cricut?
Folding heavy or cardstock paper is not an easy process like adjusitng the cricut settings for cardstock. If you have tried folding hard paper with your hand, you must have faced some difficulties. The folding is not so easy, and cracks quickly start to appear on the paper.
How to make a braided cable?
Start with a single coil and just start looping one part through the middle and around the cable. You'll have a nice braid-like look when you're done and you can then unwind the cable, bit by bit, to lengthen it (as needed).
How to store cables?
You can just use tape. Coil your cable, then wrap a strip of tape around it backwards, so the sticky side touches your fingers and not the cable. Then wrap another pieces of tape around that with the sticky side facing in so no adhesive gets on you, the cable, or anything else. Now you've tightly bound your cord, and you can easily remove that binding with a quick pull.
How to wind up a cable?
Finally, thicker cables will have a natural coil/memory to them. If you follow that natural coil about as you wrap/wind your cables up, you'll have a easier time of organizing them. To wit, hold one end with your left hand, wind the cable with the right. As you wind them up, you will feel the cable wanting to wind one way (left or right). Resist the urge the fight that, instead, let that coil the way it wants to coil as you wrap. It'll make no.1 a lot easier in the long run.
Can you wrap cable without a binder?
The Binder Clip Method: Obviously you can't have a cable wrapping video without a binder clip. If you're short on time and have one around, you can employ the same methods as the overhead knot, but just secure the cable with a binder clip rather than tying a knot at all.
Can you knot your mic cables?
As a counter to No 3: I wouldn't really knot your cables, and they will eventually damage your cables if not done carefully, especially towards the connector side of things. If you have something that is self serviceable like audio cables (think larger mic/XLR and 1/4" TS/TRS connector types), this is less of an issue however. If you're coiling and uncoiling cables every other hour or what not, this will be an issue. Generally, I wouldn't knot my cables, and it may kink and data may not flow as fast. ;P
Do you need to wrap cables?
We've shown you all sorts of ways to wrangle your cables in the past, but often you need to wrap and unwrap them when on the go. These six methods will help you keep all your cords contained quickly in most any situation.
