how do you get a locknut out of a toilet

• Firstly, make sure that you have turned the water off to the toilet tank. There is usually a valve located on the wall behind the toilet.
• Secondly, flush the toilet to empty out as much water from the tank as possible.
• Next, use a wrench or pliers to loosen and remove the lock nut from the bottom of the toilet tank.
• Finally, once the lock nut has been removed, you should be able to lift off the entire tank and access the internals.

Full Answer

How do you remove a locknut flush valve?

0:000:38Lock Nut Wrench - Flush Valve Tool - Tools For The Home - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou need to remove the flush valve and even with a large adjustable pliers here. You can see how bigMoreYou need to remove the flush valve and even with a large adjustable pliers here. You can see how big this opening is and what a much larger space this lock nut wrench will span. And for this nut.

How do you unscrew a nut under a toilet bowl?

If the bolts or nuts are plastic, they can't corrode and will come off easily. Simply pry open the cover behind the seat to expose the bolt's head. Unscrew the bolt with a pliers or a screwdriver while you hold the nut underneath with the pliers.

How do you remove a spud nut?

0:002:10How to easily replace a Urinal Spud with a Spud Wrench! - YouTubeYouTubeStart of suggested clipEnd of suggested clipClockwise. Then loosen the nut from the top of the vacuum breaker tube and the side of the mainMoreClockwise. Then loosen the nut from the top of the vacuum breaker tube and the side of the main flush valve. Body remove the main flush valve body from a wall fixture.

How do you remove a stuck wing nut?

Place the tip of a flat-head screwdriver against the right side of one wing. Tap the end of the screwdriver to get the wing nut to start rotating counterclockwise. Once the wing nut begins to turn, twist it counterclockwise by hand until it is off the threaded shaft.

How to get a bolt to hold while turning a nut?

Try Locking Pliers, Then Cut. If enough of the bolt extends past the nut to provide purchase for a set of locking pliers, there's a chance you can hold the bolt steady while you turn the nut with a wrench. Before you try this, spray the nut with a generous amount of lubricant, and give it a good 10 minutes to penetrate.

What is the fastest tool to cut a nut?

If you have enough room to operate one, the fastest tool for cutting off the nut is an angle grinder, as demonstrated by Jeff Ostroff on YouTube. Be sure to wear goggles and gloves when using this tool because sparks and small shards of metal are bound to fly. Advertisement.

What is the purpose of a nut cap?

The cap is decorative, but its main purpose is to shield the nut and bolt from rust. Coat the nut and bolt with clear lacquer or clear nail polish. Lacquer shields the metal from the moist atmosphere and prevents rust. It doesn't have any binding power of its own and won't make the nut harder to remove. Advertisement.

Can you remove locknuts from toilets?

You can remove locknuts from the bottom of toilets yourself.

Can a toilet head rotate?

There's enough space under the track for the head to rotate freely. When the bolts are holding the toilet, the heads are pressed against the underside of the flange track and can't move. If the bolt loosens because the floor is soggy or the ring is corroded, however, it can spin when you turn the nut.

Can you unscrew a toilet locknut?

Ideally, you can unscrew the locknuts with a wrench whenever you need to remove the toilet for repair or replacement, but conditions in a moist bathroom are seldom ideal , and the nuts are often difficult or impossible to turn. Advertisement.

How To Properly Loosen The Plastic Locknut

To loosen the plastic locking nut on your toilet tank, you will need a number of items, including.

How To Remove A Jammed Jam Nut

Now, if you have completed the above steps and the locknut refuses to move, you have a few options you can try. Plastic locknuts can be tricky, as they are easily damaged.

How To Loosen A Faucet Mounting Nut

Removing the faucet mounting nut is somewhat similar to removing the locking nut on a toilet tank. As with any project involving the removal of a faucet, toilet, or similar, remember to turn off the water supply to the faucet.

How To Remove The Plastic Nut From The Faucet

Plastic nuts on faucets can be a bit tricky, as the shape of some nuts may make it impossible for a basic basin wrench to get them out effectively.

How to remove locknut from bottom of toilet?

Locknuts hold the fill valve in place so that your toilet and tank fill with water properly. You will need a few key items to remove the plastic nut from your toilet tank, such as: Rag. Bucket.

How to get a toilet nut out of the tank?

Look for the plastic nut in the bottom of the toilet tank. Use a hex wrench, adjustable wrench, or pliers to clamp onto the nut. Carefully turn the nut until it comes loose and pull it out of the tank. The plastic nut may be stuck if you have an older toilet, and you’ll need to lubricate it.

How to remove plastic locknut from water tank?

You must first turn off your water supply before you remove the plastic locknut from your tank. Empty the water from the bowl and tank by flushing and siphoning the water. Disconnect the plastic piece that holds the supply hose in place with a pair of pliers or a small adjustable wrench.

How to loosen a plastic toilet nut?

Moisten a rag with hot water and place it over the plastic nut. Put the hex wrench over the rag around the nut and twist it until it becomes loose.

How to get water out of toilet tank?

This method takes the longest, but you can bail the water out of your toilet tank with a cup or bowl. Shut off the water supply line and flush the toilet a few times to empty as much of it as possible. This method comes in handy when your toilet tank’s water level simply won’t go down.

How to get rid of excess water in toilet?

Siphon. You can also siphon the excess water from your toilet tank if you need to. Put on a pair of gloves and grab a clean hose before you do anything else. Place a bucket beside the water to fill the contents of the tank with. Remove the toilet tank lid and cover both ends of the hose with your fingers or hands.

How to check if toilet water is off?

Carefully turn the fill valve to shut off the water and test it out . Flush the toilet to see if water fills the tank, and if not, the supply is off.

Why do you push a nylon nut up?

The nut must be pushed up to stay engaged while torque may be pushing it away due the nylon rounded edge. If you want to avoid damage to plastic replicate the nut hole and 4 slots in a harder material such as a piece of hardwood or flat metal with a hole and 4 filed slots on a length, long enough to become a better tool to engage with a snug fit and sharp edge against the rounded slot in the nylon.

Can you crush plastic with locking pliers?

If the plastic part you are removing is headed to the scrap/trash/recycle it might be ripe for "crush it with locking pliers" as a brute force removal technique that should still be low-stress for the porcelain.

Can you save a channel lock?

Correct. They are designed as one-time use devices, in removing them, you destroy them. So get the Channel Locks on it and remove it, you can't save it. The new valve will come with a new nut anyway.