Twist the handle of the razor counterclockwise to expose the blade. Hold the handle in your dominant hand and use the other hand to hold the head of the razor. Then, rotate the handle to the left until the head begins to the separate from the handle or the top of the head opens up to reveal the blade, depending on the razor.
How to replace the razor blade scraper blade?
[Easy to Use] - The are safety knob on both sides of plastic razor blade tool, which provides the good stability structure and make razor scrapers easy to replace the scraper blade. Just unscrewing the knob on the razor blade scraper, disassemble the upper cover to replace with a new blade, then fasten the knob.
How do I use the Hyde heavy duty razor scraper 13050?
Instructions on how to insert and remove the razor blades from the HYDE Heavy Duty Razor Scraper 13050. Grasp the razor blade backing as shown and insert into the clamp groove as far as it will freely go. Complete the blade insertion by pressing the exposed end of the blade on a benchtop, as shown, until the blade is fully seated.
How do you put a razor blade in the clamp?
To Insert the Razor Blade. Grasp the razor blade backing as shown and insert into the clamp groove as far as it will freely go. Complete the blade insertion by pressing the exposed end of the blade on a benchtop, as shown, until the blade is fully seated. To Remove the Razor Blade. Grasp the tool handle ( A ).
How do you put a razor blade on a table saw?
To Insert the Razor Blade Grasp the razor blade backing as shown and insert into the clamp groove as far as it will freely go. Complete the blade insertion by pressing the exposed end of the blade on a benchtop, as shown, until the blade is fully seated. To Remove the Razor Blade
How do you get a razor off a scraper?
Grasp the tool handle ( A ). Expose 1/4" of the blade. Rest the exposed side of the blade on the bench corner with the blade stop at the bottom. Using pliers, extract the blade from the clamp by grasping the razor blade backing ( B ).
How do you remove the blade from a razor holder?
Hold the handle in your dominant hand and use the other hand to hold the head of the razor. Then, rotate the handle to the left until the head begins to the separate from the handle or the top of the head opens up to reveal the blade, depending on the razor.
How do I change the blade on a hyper tough scraper?
0:536:15Hyper-tough scraper explained! - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay so you are going to take this screw loosen it up okay. And then you're going to take out yourMoreOkay so you are going to take this screw loosen it up okay. And then you're going to take out your false blade okay take your new blade. And you're going to drop it right in here.
How do I change the blade on my husky scraper?
All you have to do is twist the head 1/4 turn to unlock the blade and press to release the blade. To replace the blade you just do a 1/4 to the other way to lock it back into place. I like that this scraper has on board storage for blade's.
How do you change razor blades?
0:151:35How to Change Feather Plier Razor Blades - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe blade should have arrows pointing in the direction of insertion carefully slide the blade in.MoreThe blade should have arrows pointing in the direction of insertion carefully slide the blade in. Place. You may need to carefully push the razor in place by using a hard surface.
How do you remove a Gillette Venus razor blade?
How do I eject the blade cartridge for a fresh one? Push the ejection button with your thumb in the direction of the arrow. Don't put the cover back on, and don't press against cartridge while ejecting.
How do you open the mini razor blade scraper?
0:090:58Unger Mini Scraper - YouTubeYouTubeStart of suggested clipEnd of suggested clipThey come with a blade in them but this is the back of the blade to get the blade. Ready just popMoreThey come with a blade in them but this is the back of the blade to get the blade. Ready just pop this little button take the blade right out flip it around put it in make. Sure you lock it in place.
How do you change the blade on a Toughbuilt utility knife scraper?
0:192:13How it works - Toughbuilt Scraper Utility Knife - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere so what i'll do is go into knife mode and then if you want to go into scraper mode you pressMoreHere so what i'll do is go into knife mode and then if you want to go into scraper mode you press this little button here press up further blade will flip let go and now you have a scraper.
How do you use a safety scraper?
0:120:56Unger Safety Scraper 1.5 inch - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn place so if you're pushing on the glass won't go anywhere to get it back just. Press down pop itMoreIn place so if you're pushing on the glass won't go anywhere to get it back just. Press down pop it back it's in place this isn't something that's going to rattle out in your pocket.
Who makes Husky knives?
When Litton dissolved its hand tools division in the 1980s, it sold the Husky brand (and other assets, including the Blackhawk brand) to National Hand Tool. The Stanley Works acquired the Husky brand with its acquisition in 1986 of National Hand Tool.
How do you disassemble a razor?
0:221:21How to Disassemble a Razor - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo grab the tang. Open it carefully grab this side of the tang. Open it like this so you can getMoreSo grab the tang. Open it carefully grab this side of the tang. Open it like this so you can get ready to palm it for shaving.
How do you open a straight razor?
2:274:47How To Load A Straight Razor With Double Edge Razors - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd just simply blow the blade and be careful move your fingers off the way push down the that's theMoreAnd just simply blow the blade and be careful move your fingers off the way push down the that's the deal razor load it okay.
How to remove razor blade from clamp?
Using pliers, extract the blade from the clamp by grasping the razor blade backing ( B ).
How to insert a razor blade?
To Insert the Razor Blade. Grasp the razor blade backing as shown and insert into the clamp groove as far as it will freely go. Complete the blade insertion by pressing the exposed end of the blade on a benchtop, as shown, until the blade is fully seated. To Remove the Razor Blade. Grasp the tool handle ( A ).
