Tips for Removing Stuck Toilet Bolts
- Easy Way First try applying some penetrating oil such as WD40 to the bolts and allow the oil to loosen the rust and corrosion. ...
- Moderate Way If penetrating oil did not work try using a drill and metal drill bits. ...
- Hard Way If you do not have a drill, you can try cutting the bolt with a hacksaw. ...
- High Tech Way ...
How to remove rusted toilet tank bolts quickly and easily?
Wondering how to remove rusted bolts from toilet tank?
- Empty water from toilet tank. Turn off the water supply and flush the tank until it is empty. ...
- Try unscrewing first. Use a flat head screwdriver and a wrench. ...
- Be prepared for other options. ...
- Try with a mini-hack saw. ...
- Use a reciprocating saw. ...
- Consider bolt cutters. ...
- Drilling the bolts out. ...
How do you remove toilet seat with rusted bolts?
Remove rusted toilet seat bolts by using Socket Wrench if Plier fail
- Set the socket wrench on the bolt nut
- Now hold the socket wrench
- Insert the screwdriver into the bolt head hole
- Rotate the screwdriver counterclockwise and unscrew the stuck toilet seat bolts
- Follow the steps from 1 to 4 for another bolt
How to remove stubborn toilet seat bolts?
Method
- Remove bolt caps covering the seat fasteners. ...
- Look underneath the seat, you should see a mounting nut that holds the screw and seat in place. ...
- Unfasten the bolts and use the screwdriver to unwound the screw. ...
- Take out the nuts and screws. ...
- Now take out the toilet seat and wipe down with a piece of cloth or paper towel.
How to replace toilet seat with hidden bolts?
- Look carefully at the back of the toilet seat for any signs of bolts or screws. ...
- Now, that you found the bolts, you should tighten it slightly, if this is the problem with the toilet seat. ...
- Realign the toilet seat, so that it fits perfectly on the toilet before you fasten the bolts again. ...
Where are the bolts on a toilet?
How to get a toilet cap off?
How to loosen a frozen bolt?
Can you use a hacksaw to replace a toilet bolt?
See 1 more
About this website
Toilet bolt just spins when trying to remove the nut : r/fixit - reddit
I'm trying to replace my old toilet. I was able to remove the closet bolt off of one side just fine. But on the other side the bolt just spins along…
Toliet bowl stuck to floor | DIY Home Improvement Forum
I have a 22 year old house with an A.S. cadet toilet that has apparently never been removed. It sits on very nice granite floor tiles (1/2x12x12). I recently noticed the tiles and grout were wet just in front of the bowl and it smelled a little. I let it dry out for a day and then flushed the...
How To Cut Out a Toilet Flange Bolt. - BobsPlumbingVideos.com
I don’t know for sure where the majority of viewers of this website are located but I can tell you that if you’re in the New York City area and you’ve ever tried to remove a toilet bowl, chances are the flange (toilet) bolts aren’t coming off.
Removing corroded stuck toilet seat nuts and bolts plastic ... - YouTube
About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy & Safety How YouTube works Test new features Press Copyright Contact us Creators ...
Can you crack a toilet?
Drilling is difficult, and likely to crack the toilet. Unless you have a reverse threaded brill bit, as you try to drill into the bolts, they will try to tighten.
Can you remove plastic toilet seat nuts?
You Caught a Break. In the fortunate event that you installed your toilet seat with plastic nuts and bolts, removal won't be much of a problem .
Is a new toilet less trouble?
Honestly, a new toilet is less trouble.
Can you use a wrench to get a porcelain bolt out?
If these bolts are so tight that the heads twisted right off when you used a wrench, its going to be a PIA to get them out by any other means. Cutting slots into the bolt and/or using an EZ-out are possible solutions, but difficult to use without damaging the porcelain.
What to do if a toilet nut doesn't have wings?
If the nuts don't have wings, lock a pair of locking pliers around each one in turn. When you unscrew the screw, the pliers will hit against the toilet bowl and prevent the nut from turning, and it will loosen. Advertisement.
How to remove a nylon nut from a bolt?
Wearing protective gloves, heat the blade of a metal putty knife red hot with a propane torch and push it up into the nut, at its side nearest the bolt, from underneath. After it has melted its way through the nut on one side of the bolt, change the blade's orientation and make another groove on the other side of the nut, so that it can fall freely away. Repeat the operation on the second nylon nut and lift the seat off.
How long to wait after spraying a bolt?
Wait five minutes after spraying; then lock the pliers onto one of the bolts and find the longest screwdriver you can that fits the slots in the bolt head. You don't have to worry about holding the pliers, so put all your effort into turning the bolt counterclockwise with the screwdriver to loosen the nut.
How to stop threads from stripping?
To avoid stripping the threads, spray the bolts with a soap solution before unscrewing the nuts. Some nuts have wings that you can grasp with your fingers; while turning these, stabilize the bolt from above with a screwdriver. If the nuts don't have wings, lock a pair of locking pliers around each one in turn.
How to separate a nut from a nut?
Drill a hole straight up through the inside edge of the nut. Remove the bit and drill another hole 60 to 90 degrees away, then tap the section between the holes with a chisel, and the nut should separate. If not, drill more holes between the two you just drilled. After tapping off that section of the nut, you should be able to pry ...
How to melt a nylon nut?
If it doesn't, and the nut is nylon, you can melt it off with a hot putty knife. Wearing protective gloves, heat the blade of a metal putty knife red hot with a propane torch and push it up into the nut, at its side nearest the bolt, from underneath.
What are toilet seats notorious for?
Toilet seats are notorious for corroded, hard-to-remove bolts.
What are the plastic lock nuts on toilets?
In every toilet tank, there are plastic lock nuts that secure various fixtures in place. They are strong enough to provide solid support to secure the fill valve and other fixtures. However, one misstep can damage the locknut, making it a nightmare to remove.
How to loosen a faucet nut?
To loosen faucet mounting nuts, use channel-type pliers to grip the nut that holds the faucet body in place. Rotate the nut counterclockwise to remove it. There may also be a spout mounting nut. If there is, use the same techniques.
How to remove lock nut from plastic?
Use caution as not to go too deep or cut through anything else. Once you have cut through the nut, use the flathead screwdriver to push the two ends apart , then remove the lock nut with your hands.
How to remove a hex nut?
To remove the nut, you can use whichever tool you choose: a pair of pliers, a spud wrench (specifically designed for removing hex nuts), or an adjustable wrench. Turn the plastic nut counterclockwise to remove it.
How to fit a lock nut?
Set the pliers on the narrowest setting that will fit around the lock nut. Fit the pliers around the lock nut. Come from either the top or bottom, not the side. Using both hands, grip the pliers while rotating to spin the nut.
Can plastic nuts be used on faucets?
Plastic nuts on faucets can be a bit tricky , as some of them may have shapes that prevent a basic basin wrench from efficiently removing it.
Can plastic lock nuts be removed?
Now, if you have completed the steps outlined above and the locknut refuses to budge, you have a couple of options you can try. Plastic lock nuts can be tricky to remove as they can damage easily.
How to remove a bolt that is stuck in place?
In most cases, you can remove a bolt by unscrewing the nut from the bolt with a wrench. If the bolt is rusted or otherwise stuck in place, however, you’ll need to find another way to remove the bolt. If the hexagonal surfaces of bolt and nut haven’t been stripped, try heating the bolt with a propane torch to loosen it.
How to unscrew a stuck bolt?
Try to unscrew the stuck bolt with the extended wrench. Hook the end of your box-end wrench around the head of the stuck bolt, and hold the wrench at the very end of the extender bar. With your other hand, grip the nut with a large pair of pliers. Pull sharply on the end of the wrench to try to loosen the stuck bolt. Ideally, the penetrating spray will have weakened the bolt’s resistance so that it loosens.
How to remove a stuck bolt from a screw extractor?
If the screw extractor doesn’t remove the stuck bolt itself, pull the bolt out with a wrench. Set the end of a box wrench over the head of a drilled-out bolt and turn it counterclockwise to loosen the bolt.
How to loosen a bolt with a box end?
Loosen the bolt with an extended wrench. Insert the end of your box-end wrench into a hollow metal bar. Hook the wrench onto the bolt and grasp the nut with a pair of large pliers. Hold the nut in position and pull on the end of the wrench. Give 4-5 sharp tugs and see if the bolt moves.
What to use to loosen a bolt?
Use a pair of vice-grip pliers if the bolt or nut are stripped. If the sharp hexagonal sides of the stuck bolt have been stripped and rounded, a box-end wrench will slip off when you try to loosen the bolt. Vice-grip pliers have teeth on the inside of their rounded jaws and can be fastened tightly around the flat surfaces of a stripped bolt.
How to remove a rusted bolt?
Strike the head of the bolt 6-12 times with a hammer. Once the rust-penetrating thread loosener has loosened up the rusted bolt, hit it with a hammer to jar the bolt out of the position its stuck in. Blows from a hammer can also create micro-fractures throughout the bolt, making it easier to remove.
How to remove a bolt that is not loose?
I suggest first spraying the bolt with WD-40 to see if that loosens it up. If not, you may need to use a tool, like a cold chisel, to knock off the head of the bolt so you can remove it.
How to get a toilet nut out of the tank?
Look for the plastic nut in the bottom of the toilet tank. Use a hex wrench, adjustable wrench, or pliers to clamp onto the nut. Carefully turn the nut until it comes loose and pull it out of the tank. The plastic nut may be stuck if you have an older toilet, and you’ll need to lubricate it.
How to loosen a plastic toilet nut?
Moisten a rag with hot water and place it over the plastic nut. Put the hex wrench over the rag around the nut and twist it until it becomes loose.
How to remove plastic locknut from water tank?
You must first turn off your water supply before you remove the plastic locknut from your tank. Empty the water from the bowl and tank by flushing and siphoning the water. Disconnect the plastic piece that holds the supply hose in place with a pair of pliers or a small adjustable wrench.
How to remove locknut from bottom of toilet?
Locknuts hold the fill valve in place so that your toilet and tank fill with water properly. You will need a few key items to remove the plastic nut from your toilet tank, such as: Rag. Bucket.
How to get water out of toilet tank?
This method takes the longest, but you can bail the water out of your toilet tank with a cup or bowl. Shut off the water supply line and flush the toilet a few times to empty as much of it as possible. This method comes in handy when your toilet tank’s water level simply won’t go down.
How to get rid of excess water in toilet?
Siphon. You can also siphon the excess water from your toilet tank if you need to. Put on a pair of gloves and grab a clean hose before you do anything else. Place a bucket beside the water to fill the contents of the tank with. Remove the toilet tank lid and cover both ends of the hose with your fingers or hands.
How to check if toilet water is off?
Carefully turn the fill valve to shut off the water and test it out . Flush the toilet to see if water fills the tank, and if not, the supply is off.
What happens if you don't get the bolts off a toilet?
When the old toilet doesn't come off smoothly , you may find that the anchor bolts, also referred to as closet bolts or flange bolts, are stripped when you try to remove the nuts. This common problem takes a little work to get the nuts and old bolts out.
How to remove stripped threads from a bolt?
Slide the nut over the stripped threads and grasp the bolt beneath the nut with a pair of pliers if the threads are only stripped lower on the bolt. Turn the nut counterclockwise with a wrench to remove it. Repeat to remove the other nut.
Where is the water shut off valve located on a toilet?
Turn the water supply shutoff valve clockwise to turn off the water supply to the toilet. This valve is located beneath the tank near the wall.
How to tighten anchor bolts?
Place the nuts on the anchor bolts and turn them clockwise by hand to tighten. Sit on the bowl and tighten the nuts with a wrench. Don't over-tighten the nuts. Cut off the tops of the bolts with a hacksaw, so the plastic covers fit over the bolts. Retighten the nuts, if needed.
Where are the bolts on a toilet?
The bolts protrude through holes on either side of the toilet base, just behind the bowl, and a washer and nut screwed onto each bolt to hold down the toilet. Since toilets reside in the most humid room in the house, it's common for these nuts and bolts to corrode and "freeze," so that you can't get the nut off the bolt -- ...
How to get a toilet cap off?
If you can't just pull off the cap, pry it off with a flat-blade screwdriver. Loosen the nut as best you can, using a wrench or a socket set to turn the nut counterclockwise. If the bolt isn't completely frozen, you might be able to loosen it a bit. ...
How to loosen a frozen bolt?
Loosen the nut as best you can, using a wrench or a socket set to turn the nut counterclockwise. If the bolt isn't completely frozen, you might be able to loosen it a bit.
Can you use a hacksaw to replace a toilet bolt?
If you don't have a rotary tool, you might be able to use a hacksaw. Work the blade between the nut and the washer and saw through the bolt; however, the bolt placement on some toilets can make it impossible to use a hacksaw. Replacement bolts are inexpensive and available at hardware and home-improvement stores.
