Steps On How To Hang A Heavy Curtain Rod In Drywall
- 1. Install Plastic Anchors On Both Sides When it comes to hanging a heavy curtain rod on the wall, you will want to have additional support along the ends. ...
- 2. Find Center Point Of The Curtain Rod You will also want to start finding the center point of the curtain rod. ...
- 3. Install Center Support Bracket ...
- 4. Test The Curtain Rod ...
How to hang curtains correctly the first time?
Part 3 Part 3 of 3: Adding Your Curtains Download Article
- Remove your rod to hang the curtains. Once you're certain that your brackets can hold your rod, remove it to attach your curtains.
- Add the curtains onto the rod. Some curtains are attached to the rod by curtain rings while others are threaded directly through the rod.
- Put the rod back into place. ...
How to hang shower curtains without using a rod?
- Measure the spacing for your knobs on the width of the window. ...
- Mark the spacing with a pencil.
- Using an electric drill, drill holes at the markings. ...
- Drill the screw into the holes.
- Attach the wooden knobs on top of the screws.
- Measure the width of the fabric on the curtain where you want your wooden knobs to be located.
How to install curtain rods without a drill?
You must first choose where to hang curtain rods and select the best type for your windows:
- Measure the width of your window frame. ...
- Decide whether you want your curtain rod to hang on the window frame or extend past it. ...
- Allow about 3 inches on each side of the window. ...
- Make a mark about four inches above your window for mounting hardware. ...
- For grommet curtains, you will need to take into account the placement of the grommet. ...
How to hang a dartboard on drywall?
- Drill a hole in the wall barely wide enough to insert each wall anchor or the folded "wings" of the toggle bolts. ...
- Push or hammer each anchor into the hole so the opening for the screw faces you. ...
- Insert each screw through its respective hole on the dartboard mounting bracket. ...
- Insert each screw into an anchor, tightening it with a screwdriver. ...
How do you fix drywall strong enough to hold a curtain rod?
1:302:38How to Repair Drywall Strong Enough to Hold a Curtain Rod : Wall RepairYouTubeStart of suggested clipEnd of suggested clipNow this is going to take a couple applications that way we can make sure that it's all the way backMoreNow this is going to take a couple applications that way we can make sure that it's all the way back in the hole and dries. Properly. Now we'll go ahead and let that dry take a real light sandpaper.
Can you hang curtain rod on drywall?
You'll need to use plastic wall anchors to provide proper support if you're installing in drywall. Fasten the brackets to the walls using your drill or screwdriver. Having a hand tool ready often makes this job easier, since it can be hard to use a larger electric drill when mounting curtain rod hardware to the wall.
How do you anchor heavy curtains?
Screwing directly into a stud is the most secure way to support your curtain rod and brackets. Use a stud finder to locate a stud above your window before trying other methods. If there isn't a stud, you need to use a drywall anchor and a screw to reinforce your curtain rod brackets.
How long can a curtain rod be without a middle support?
1 ⅜” Wooden rods and 1 ⅜” Designer Metals can go 60 inches without support. 2” Wood can go up to 96” and should have support brackets if high up. Wrought iron can go up to 96” without support but is heavy so support is safer. It's safe to support every splice and joint on a rod.
Do curtain rods need to be hang on studs?
Well, you do NOT need a stud to hang a curtain rod, but you will need a special type of wall anchor to hold the weight. There are two different types I like to use: a drywall anchor or toggle bolts.
How do you hang heavy curtains on plaster walls?
The Easy Way to Hang Curtains on Plaster WallsStep 1: Mark the Spot for the Bracket. ... Step 2: Drill Top Hole. ... Step 3: Add Screw. ... Step 3: Insert a Molly Bolt Into the Hole. ... Step 3.5: Add Screw. ... Step 4: Dry Fit Bracket and Mark Second Hole Hole. ... Step 5: Drill Second Hole and Add Screw. ... Step 6: Repeat for Other Brackets.More items...•
Can drywall support curtains?
Hanging curtains on drywall is not as simple as it looks. Drywall will not hold a screw because it's not solid. If you mount a curtain rod with a screw, over time you will end up with a sagging curtain and hole. Using drywall anchors is the only solution.
How can I hang heavy curtains without drilling?
How to Hang Curtains Without Drilling: 3 MethodsSecure the hardware with adhesive hooks. Adhesive hooks or adhesive strips are versatile hanging tools you can purchase in various sizes and strengths. ... Use magnetic curtain rods. ... Use tension rod curtains inside window frames.
How much weight can drywall anchors hold?
Toggle bolts are the types of drywall anchors that can support up to 50 pounds, while steel hollow-wall anchors have a drywall anchors weight limit of up to 100 pounds.
How much weight can curtain rods take?
A tension rod can hold between 10-45 pounds, depending on its material. However, the average tension rod can handle about 20 pounds. Whether you want to suspend curtains or clothes, a tension rod makes an excellent addition to your home.
How do you hang heavy curtains with hooks?
1:102:48How to hang your curtains perfectly - YouTubeYouTubeStart of suggested clipEnd of suggested clipThen fit the hooks as a rough guide approximately. Four to seven pockets apart or 7 centimetersMoreThen fit the hooks as a rough guide approximately. Four to seven pockets apart or 7 centimeters depending on fullness if you have too many hooks this will restrict the curtains running off the window.
How do you hide the middle bracket on a curtain rod?
One traditional way to hide the brackets and the entire rod is by using a valance. This fixture sits on top of the rod and brackets and usually matches your curtains. It may be solid or made of fabric. You can always hang something else above the rod and brackets, like a tapestry or other decoration.
How do I keep my curtain rod from sagging?
Here are some of the best practices to keep your curtain rods from sliding.Extend the Curtain Rod. ... Strengthen the Rod. ... Hang Your Brackets Wide. ... Make Sure the Curtain Rod is the Right Size. ... Tighten the Screws. ... Use Rubber Bands. ... Duct Tape. ... Command Strips.
What size curtain rod do I need for 72 inch window?
A rod that is 48 to 84 inches in length will adequately fit a window up to 72 inches wide. This size is the most common window you will find in many homes.
How do I know where the studs are in my wall?
Measure From a Corner In all likelihood, there's a wall stud in the corner of your room to which the drywall is attached. There may be some overlap where the drywall meets, but it's usually pretty safe to assume that if you measure 16-inch increments in either direction from the corner, you'll find a stud.
How do you find a stud in the wall without a stud finder?
1:003:585 genius ways to find studs in a wall... without a stud finder! - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo my first go-to technique for finding studs without a stud finder is to use receptacles. AndMoreSo my first go-to technique for finding studs without a stud finder is to use receptacles. And switches to locate the studs. Most receptacle. And switch boxes are mounted to the side of a stud.
How do you find a stud to hang a curtain rod?
0:452:01How to Find the Window Stud to Hang Curtains on Plaster Walls - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can draw an imaginary line. Straight down and you can attach anywhere to that stud there theseMoreYou can draw an imaginary line. Straight down and you can attach anywhere to that stud there these curtains are hung on the trim of the window.
What anchors for plaster walls?
Plastic wall anchors, Molly Bolts or Toggle Bolts? Plastic wall anchors don't work with lath and plaster walls. Instead, use plaster anchors made of metal like a molly bolt or a toggle bolt. Be sure to use one that's long enough to get behind the plaster and lath.
How do you hang a rod on a plaster wall?
Drill a hole through the plaster wall, insert the toggle bolt through the rod holder, press the toggle through the drilled hole and tighten it down with a screwdriver. Hang the dowel rod on the closet rod holders.
Can you use drywall anchors in plaster?
Drywall anchors can be used on plaster walls the same way they'd be used on drywall. However, in many cases, they're not necessary, because it's easier to get a screw into the lath. I only use drywall anchors on plaster walls when I've gotten other screws into the lath or a stud, and I'm hanging a large piece.
How do you hang a curtain rail on drywall?
0:181:18GripIt - How to hang a curtain pole to a plasterboard wall - YouTubeYouTubeStart of suggested clipEnd of suggested clipAfter tapping you're fixing into the wall insert the screwdriver in the rotary inserts and turn 90MoreAfter tapping you're fixing into the wall insert the screwdriver in the rotary inserts and turn 90 degrees to the right. This will allow the wings to open at back and secure your grip.
How do you fix a drywall curtain rod?
If it's larger than an inch, you'll need patching compound and some extra support to ensure the rod will stay in the wall.Get the right tools. ... Clear out the hole. ... Stuff the hole with newspaper. ... Mix patching compound with water. ... Fill the hole with patching compound. ... Sand and paint the patch. ... Measure and rehang your curtains.
How do anchors work in drywall?
Drywall anchors live up to their namesake by anchoring into drywall panels. You can push them into a pilot hole. As you tighten a screw into a drywall anchor, the drywall anchor will expand. The back of the drywall anchor will essentially expand around the back of the drywall panel.
How do you install a drywall anchor without a drill?
0:472:33How to Put an Anchor in Drywall Without a Drill - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the first thing we need to do is just take a regular Phillips head screwdriver. And put it whereMoreSo the first thing we need to do is just take a regular Phillips head screwdriver. And put it where you want to bank your new hole.
What is the best anchor for curtain rods?
GeeFix are the best drywall anchors for curtain rods. To hang heavy curtains on drywall is simle and secure with GeeFix . Each pack of 4 comes with simple instructions on the back of the packaging. The video below will show you how to hang heavy curtains on drywall: GeeFix. Fix it once.
Why won't my drywall hold a screw?
Drywall will not hold a screw because it’s not solid. If you mount a curtain rod with a screw, over time you will end up with a sagging curtain and hole. Using drywall anchors is the only solution. GeeFix fixings are plastic drywall anchors which are designed so screws only go into the plasic anchor and the weight is distributed.
How to secure heavy curtains?
As you know, attaching the brackets to a stud behind the plasterboard is the best way to ensure heavy curtains are secure, but this isn’t always possible. Studs are only found every 40-60 centimetres, so it’s unlikely there would be one everywhere you want to put a bracket- that’s where wall anchors come in.
Where can I buy wall anchors?
Wall anchors are available at most hardware stores and come in a variety of shapes and materials. Before making a purchase, be sure to check they’re rated for the amount of weight you’ll be putting on this fixture and it’s appropriate for wherever it’s installed (i.e. wall anchors instead of ceiling anchors).
How to check the position of the second anchor?
Simply place one end of the rod in the bracket and hold the other end against the mark while you check the level with a spirit level.
