- Lay the fuel hose out from the desired tank location to the motor. ...
- Cut the hose between the primer bulb and the fuel tank. ...
- Insert the fuel tank quick-connector into the fuel-tank end of the hose and secure it, using a hose clamp and Phillips screwdriver.
- Insert the brand-specific quick connector into the motor end of the fuel hose. Secure the connector using a hose clamp and Phillips screwdriver.
- Squeeze the release tab on the motor quick connector and slide it onto the motor fuel fitting. ...
- Fill the fuel tank. Open the fuel tank vent, if the tank is not self-venting. ...
How do you connect a fuel tank to an outboard motor?
Tanks with nonstandard fittings require a custom-built hose to complete the connection. Parts for building a fuel hose are available from outboard dealerships, marine hardware stores and even some of the better general hardware stores. You can assemble a fuel hose to connect your fuel tank to your outboard motor using basic tools.
What is the hose connected to the motor for?
The hose connection is for a garden type hose to connect to it in order to flush the motor out. If you want to run the motor you have to give it water for cooling.
What is an outboard with a garden hose?
Built-in garden hose attachments are a standard part of many outboards manufactured in the past decade or so. These attachments make flushing easier, because the engine usually doesn't need to be running (and in some cases, should not be) to accomplish the flushing procedure.
Where can I get a fuel hose for my Boat?
Parts for building a fuel hose are available from outboard dealerships, marine hardware stores and even some of the better general hardware stores. You can assemble a fuel hose to connect your fuel tank to your outboard motor using basic tools. Lay the fuel hose out from the desired tank location to the motor.
Where do you connect the hose on a boat motor?
2:085:14Running Your Outboard Boat Motor On Land - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay you find where your intake is on your boat motor. It's right here on this one that's where thisMoreOkay you find where your intake is on your boat motor. It's right here on this one that's where this boat motor sucks water out of the link up into the engine to cool it down okay.
How do you start an outboard motor on a garden hose?
6:539:23how to start and run a outboard motor on a garden hose - YouTubeYouTubeStart of suggested clipEnd of suggested clipSlide it up over on the foot part of your motor down here you have some in intake vents where yourMoreSlide it up over on the foot part of your motor down here you have some in intake vents where your water goes in to cool your engine. Slide that up to those muffs has that covered.
How do you run an outboard engine out of water?
To run your boat motor out of water, start by attaching a hose to your motor's water intake so you can flush in water, which will avoid damaging the engine. Once the hose is attached, turn on the water faucet. Then, pull the gear shift to neutral and start the engine.
How do you use ear muffs on an outboard?
5:198:50How to use Boat Motor Flushing Muffs - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd to fit covering these holes perfectly. Here's the muffs installed on an outboard motor. And asMoreAnd to fit covering these holes perfectly. Here's the muffs installed on an outboard motor. And as you can see around this side the cup actually folded itself over.
Can you run outboard with hose connection?
Flush muffs are the most common way to flush an outboard; they're available at most marine stores and online resellers. They're inexpensive, and easy to use. Connect to a garden hose, fit the muffs over the engine's water intakes on the sides of the gear case, turn the water on, start the engine, and let it run.
How long can an outboard run without water?
How Long Can an Outboard Run Without Water? An outboard motor's water pump will be damaged in as little as a few seconds without a water source. Depending on the size of the outboard engine itself and ambient temperatures, it may be able to go a few minutes without damage.
How do you tow a tube with an outboard motor?
3:228:27How to Safely Pull a Tube Behind a Boat - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn an outboard or i o power board that's going to be on a ski bar. Or on a ski hook eye that's onMoreOn an outboard or i o power board that's going to be on a ski bar. Or on a ski hook eye that's on the transom of the boat. This is going to give you a little bit of height out of the water.
How long can I run boat out of water?
The maximum amount of time you can run your boat motor without water is between 2 and 10 seconds if you must.
How long can a boat sit without running?
One of the most commonly-asked questions we get is, “Is it okay if my boat isn't running for a while in Fort Lauderdale, FL?” The answer is yes—but you have to do some maintenance beforehand. As long as it's well maintained before going into storage, a boat can sit for a few months, a few years or even a few decades.
Is it safe to run outboard with muffs?
Otherwise no real time limitations on muffs as long as the flow is good and you don't put it in gear. The only downfall with adjusting idle on muffs is it'll run perfect on the hose but may not start at the dock because of the pressure difference on the exhaust.
Should you flush your outboard motor after every use?
Most outboard manufacturers recommend a freshwater flush after every use in saltwater to clear the cooling passages of salt residue and scale that can accumulate and impede the flow of vital cooling water through the engine.
Can you put an outboard in gear out of water?
There is no difference putting the motor in gear at idle in or out of the water. The prop shaft will actually spin the prop with less initial resistance than if the prop was in the water.
How to change fuel hose on a motor?
Step 1. Lay the fuel hose out from the desired tank location to the motor. Route the hose so that it is protected from damage and does not present a trip hazard. Ensure that the arrow on the primer bulb points in the direction of the fuel flow -- from the tank to the motor. Cut the fuel hose to length.
How to connect a fuel filter to a boat?
Cut the hose between the primer bulb and the fuel tank. Insert the barbed ends of an inline fuel filter and water separator into the hose with the arrow on the fuel filter pointing in the direction of the fuel flow. Ensure that the filter is in a protected but accessible area of the boat. Secure the hose to the inline filter using at least two hose clamps and a Phillips screwdriver.
How to check if fuel tank is self venting?
Open the fuel tank vent, if the tank is not self-venting. Pump the primer bulb in the fuel hose until the inline filter is filled with fuel and the bulb has a firm feel when it is squeezed. Check all of the fuel line connections for leaks.
Can you use ethanol in a fuel line?
Make certain the fuel line is rated for gasoline use, not diesel, and that it is formulated for use with fuel containing ethanol. Ethanol is a relatively new additive to fuel. Ethanol can damage and degrade older types of fuel hoses and can lead to loss of engine power during operation.
Can a boat leaking gas be a fire extinguisher?
Ensure that your fire extinguisher is rated for gasoline fires and that it is fully charged and readily accessible. Never operate a boat that is leaking gasoline. Gas fumes are heavier than air and will collect in the bilges and other low spots in the boat.
Can you use a gas outboard motor without a fuel tank?
Gasoline-powered outboard motors without built-in fuel tanks must be connected to a remote fuel source. Many outboard manufacturers sell fuel tanks and fuel hose kits with the appropriate fittings built into the hose that will connect to their motors.
How to flush outboard motor?
Flush muffs are the most common way to flush an outboard; they're available at most marine stores and online resellers. They're inexpensive, and easy to use. Connect to a garden hose, fit the muffs over the engine's water intakes on the sides of the gear case, turn the water on, start the engine, and let it run. That's it, with the following precautions: 1 If your engine has additional water intakes that are not being directly fed water via the flushing muffs, they must be sealed off with a bit of duct tape, or overheating may occur. 2 If your engine doesn't have water intakes on the sides of the gear case, you will need a special type of flushing attachment that covers the front of the gear case. These can be purchased from aftermarket shops. 3 When attaching the muffs, be sure they cover the water inlets completely and don't pop or slide off when the water is turned on. 4 Be vigilant, and don't leave the engine while flushing. Watch the engine's "tell-tale" overboard water indicator to ensure that the engine is pumping water. 5 The engine should be kept in neutral and not run above a fast idle speed (1,000 rpm maximum).
Where is the flush port on a Mercury outboard?
Mercury's procedure varies by engine size and series. Smaller and midsize four-stroke outboards use the flush port at the rear of the engine . The engine must be warmed up to open the thermostat and circulate water throughout the engine's cooling passages completely. The engine can be vertical or tilted.
Why flush outboard with fresh water?
The buildup of salt in your outboard can cause blockages that result in overheating and eventual corrosion. (Photo: John Tiger) Back in the day, flushing an outboard with fresh water was done only one way. A set of "ear muffs" or "flush muffs" was fitted around the engine's gearcase to cover the water intakes, connected to a garden hose ...
What is a built in flushing attachment?
Built-In Flushing Attachments. Built-in garden hose attachments are a standard part of many outboards manufactured in the past decade or so. These attachments make flushing easier, because the engine usually doesn't need to be running (and in some cases, should not be) to accomplish the flushing procedure.
What to do if water pressure is low on Honda?
Honda warns that if water pressure is low, tape should be used to close off the engine's water intakes on each side of the gear case . Larger engines (60 to 250 hp): Honda's only recommended flushing procedure is to use the factory flushing port connected to a garden hose with the engine not running.
How much water pressure should I use for a car?
Water pressure should be between 20 and 40 psi. (You can buy a pressure gauge attachment at a hardware store to monitor psi.) Flush for at least five minutes at an idle speed, with the engine in a vertical position. When using the flushing port, it is not necessary to run the engine.
How long to run Mercury engine in neutral?
Start the engine and run at idle speed in neutral for three to five minutes. For flushing without muffs, Mercury offers a garden-hose adapter that connects to a port in the lower engine cowl; this port is accessed by removing a dust cover.
How does a boat motor work?
Water is circulated through a system of ports and passages and then out the water exhaust port carrying with it excess heat. Boat motors can be damaged if salt and silt are not flushed from the cooling system. Flushing a boat motor can be accomplished hooking a garden hose to a flushing device which directs fresh water into ...
Can propellers be removed?
For added safety the propeller can be removed. Be certain the motor shift lever is set to neutral before starting the motor. Shut off the motor immediately if you suspect water is not circulating through the cooling system and the motor is running hot.
Can you tilt a motor for flushing?
Check the owner's manual for directions specific to your motor. Some manufacturers recommend the motor be tilted for thorough flushing. For added safety the propeller can be removed.
What is a hose connection?
The hose connection is for a garden type hose to connect to it in order to flush the motor out. If you want to run the motor you have to give it water for cooling. If you just hook up a hose to the flush connection, that is so you can flush the motor without running it.
How long can you run a cowling on a flush adapter?
If the engine has a flush adapter and your water source has enough pressure to cause a stream of water to discharge from the cowling drain (pee hole), then it is fine to run the engine on the flush adapter only, but it's limited to 1500 RPM max and no longer than 15 minutes.
Do you have to give an outboard water?
Anytime that you run a outboard you have to give it water for cooling. Its water cooled so water runs through passages that cool the block. If my memory is correct that motor has the flush connection is not down near the lower unit.
Can you run a motor out of water?
If you want to run the motor out of the water you got to run it on the muffs or in a tank or on the lake. What you are talking about will at the least burn up the impeller, but its not good to run it like that. I would pull the lower unit and check to see if you burned up the impeller.
