How do I position my REL subwoofer?
Turn inward toward the center of the room pointing directly or almost directly at the prime listening location. * These are recommended best practices for positioning a REL Subwoofer, always refine placement and angle by ear.
How to hook up a subwoofer to a receiver?
If the subwoofer features spring clips in order to use speaker wire, then you can use the speaker output of the receiver to hook it all up. This process is the same as connecting a basic stereo speaker. Be sure to mind the channels.
Do you need a signal connection cable for a REL subwoofer?
By the way, did you know that you likely don’t need to use any signal connection cable at all? REL has designed wireless capability into many of their subwoofers, and this only helps you as a new or considering REL owner. I’ll explain why.
How do I connect my speakers to my REL High Level?
Note: You connect your left and right main speakers to the same terminals on your receiver or amplifier as the REL high level connection. If more convenient you can also attach the high level cable to the terminals on your main left and right speakers without any loss of signal quality.
How do you install a REL subwoofer?
0:322:31REL Acoustics How To: High & Low Level Subwoofer Tuning ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis should be at about the 12 o'clock position on the crossover knob. Then turn the high / lowMoreThis should be at about the 12 o'clock position on the crossover knob. Then turn the high / low level output up so that both the rel and speaker are roughly equal in volume.
How do I connect my subwoofer to my sound system?
If you are using your subwoofer with a home theater receiver, the connection is simple: Just run an audio interconnect cable like this one from the receiver's subwoofer output to the subwoofer's line input (pictured above). If the subwoofer has an input labeled LFE, use that one.
How do I connect my subwoofer to my amp?
How to Connect a Subwoofer to an AmplifierTurn the amplifier and the subwoofer so the backs are facing you. ... Locate the plug on your amplifier that is labeled Sub Out, LFE (low frequency effects) Out or Line Out [source: KEF]. ... Connect the cable that was included with the subwoofer to the amplifier's terminal.More items...•
How do I connect to REL Speakon?
2:105:42How to Connect REL T/9x Subwoofer via High Level Connection - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou will want to connect the red cable to the positive pole on one speaker in this case it will beMoreYou will want to connect the red cable to the positive pole on one speaker in this case it will be the right speaker. I'll then connect the black cable to the black binding post for the right.
How do you connect a subwoofer to anything?
Using a subwoofer cable (RCA cable), connect the subwoofer to the AV receiver by running the cable from the receiver's subwoofer output to the subwoofer's line input. Klipsch subwoofers can be connected via the LFE channel, the white RCA connection, or in a stereo pair by using both the white and red RCA connections.
How do you connect a speaker wire to a subwoofer?
34:3336:423 Ways to Connect Subwoofer LFE to Audio Receiver | Beginner GuideYouTubeStart of suggested clipEnd of suggested clipAnd your subwoofer to a speaker. All right the other way that you could connect. This would be toMoreAnd your subwoofer to a speaker. All right the other way that you could connect. This would be to connect this right directly to this speaker. And then connect this sub. Using the subwoofer cable that
How do you wire a powered subwoofer?
1:443:47How to install a powered subwoofer in your car | Crutchfield videoYouTubeStart of suggested clipEnd of suggested clipBoth the turn on wire and RCA signal cables need to be connected to your stereo. Run these cablesMoreBoth the turn on wire and RCA signal cables need to be connected to your stereo. Run these cables behind the dash to your stereo.
Can I connect a subwoofer to a stereo?
The subwoofer is hooked up to the receiver with a single interconnect cable. Stereo receivers, pre-amps, and integrated amplifiers rarely have subwoofer output jacks or offer bass-management options. So instead of using those connections, we'll use the subwoofer's speaker-level, aka "high-level," inputs.
Why does my subwoofer have two inputs?
Dual input allows the subwoofer an extra sensitivity adjustment. Normally, it would be enough to use a mono LFE subwoofer signal from its processor. If you have a processor with very low output so you can use a Y-splitter. By using both inputs with the same mono signal doubles the subwoofer sensitivity.
How do you hook up a subwoofer to a 2 channel system?
If you're using two subs, connect the left-channel sub to the left pre-out, and the right-channel sub to the right pre-out. If you're using a separate preamp and power amp, and the preamp has only a single set of pre-outs, you'll need two RCA Y-adapters, to split the pre-outs to simultaneously feed power amp and sub.
How do you hook up a subwoofer to a receiver without sub?
Right: An RCA Y adapter that can be used with a line level converter to connect to a subwoofer with a single RCA input jack. For subwoofers with only 1 or more RCA input jacks (no speaker level inputs), a simple way to connect them to a receiver with no subwoofer output is by using a line level converter.
How do I connect my Denon receiver to my REL subwoofer?
0:252:03Connecting a Rel as a Dedicated Rear Subwoofer (Theater) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe final step is to plug the speakon connector at the other end of the cable into the relMoreThe final step is to plug the speakon connector at the other end of the cable into the rel subwoofers high level input. Since you're using this in a theater application to support the rear channels.
How to connect a subwoofer to a receiver?
If the subwoofer features spring clips for speaker wire, use the receiver's speaker output to hook it all up. This process is the same as connecting a basic stereo speaker. Be sure to mind the channels. If the subwoofer has two sets of spring clips (for speaker in and speaker out), it means that other speakers connect to the subwoofer, which then connects to the receiver to pass along the audio signal. If the subwoofer has only one set of spring clips, the subwoofer must share the same receiver connections as the speakers. The best way to accomplish this is by using banana clips that can plug into the backs of each other rather than overlapping bare wire.
How to plug in a subwoofer?
If the subwoofer's LINE IN uses RCA cables and the subwoofer out on the receiver/amplifier also uses RCA, plug it in using an RCA cable. If the cable is split on one end (a y-cable for both right and left channels), plug it in the R and L ports on the subwoofer. If the receiver/amplifier also has left and right RCA plugs for subwoofer output, be sure to also plug in both to the receiver.
What does it mean when a subwoofer has two spring clips?
If the subwoofer has two sets of spring clips (for speaker in and speaker out), then it means that other speakers connect to the subwoofer, which then connects to the receiver to pass along the audio signal. If the subwoofer has only one set of spring clips, then the subwoofer will have to share the same receiver connections as the speakers.
How many cords are needed for a subwoofer?
Subwoofers are typically easy to connect, given that there are usually only two cords to deal with: one for power and one for the audio input. You're far more likely to spend the bulk of time positioning and adjusting a subwoofer for the best performance than actually plugging in a pair of cables.
Do subwoofers have spring clips?
If the subwoofer has only one set of spring clips, then the subwoofer will have to share the same receiver connections as the speakers. The best way to accomplish this is by using banana clips (versus overlapping bare wire) that can plug into the backs of each other.
Where to place a REL speaker?
Because RELs are engineered to produce foundational low bass, it is beneficial to place a single REL into a structural corner at the front of the room, immediately behind the main front speakers. If you have a choice of corners, select the corner that is either built from stronger material (Masonry vs. Sheetrock).
Where is the best place to place a subwoofer?
Ideal positioning is located in one of two front corners nearest the location of the screen and main speakers. Corner positioning reinforces deep bass and produces more efficiency, output for a given volume setting. Take care to turn the sub inward at approximately a 45-degree angle to obtain best release of low notes.
What is the use of REL 3D?
With Dolby 9.1.2 Atmos, 9.1.4 Atos and larger systems, we strongly advocate for the use of the REL 3D set-up, as this allows you to harness the atmospheric bass and huge soundstages made available through these extended formats.
How many RELs are needed for 11.2 Dolby Atmos?
In addition to the REL 3D protocol, when using 11.2 Dolby Atmos, it is recommended that 2 additional smaller RELs be used for each additional pair of surround speaker, 1 for the extra surrounds and another for the heightsurrounds. A third additional REL may be used to support the width enhancing speakers but this is overkill in most instances. This will serve to provide the low frequency under pinning for each pair of surround/height speakers.
What is Dolby 5.1 REL 3D?
With Dolby 5.1+ REL 3D we are finally able to deliver the performance promised by 5.1 professional standard by underpinning all three groups of speakers (L/R main, C and Surrounds) with deep, dimensional bass. Doing so places the viewer in the middle of the action since scale, dynamics and excitement are all produced by deep bass. Allowing it to arrive from each channel creates a three dimensional stage in which you are entirely immersed.
How many RELs are needed for surround speakers?
In addition to the REL 3D protocol, when using 9.2 Dolby Atmos, it is recommended that 2 additional smaller RELs be used for each additional pair of surround speakers. This will serve to provide the low frequency under pinning for that pair of surround/height speakers.
Why use stereo pairs?
Using stereo pairs (two REL subwoofers) to support high quality speakers extends far beyond simply increasing the quantity of low bass in a system. A Stereo pair of RELs greatly increases the focus, clarity and range of the entire sound system by enhancing details in the upper-midrange and low treble of the speakers. This greatly illuminates the musicians or action in a movie soundtrack, increasing intelligibility and intimacy of the moment.
