How to Hook Up the Ice Maker on Your New Refrigerator
- Locate the refrigerator connections at the base of your refrigerator, referring to the installation manual for a picture of what the connection should look like.
- Remove the PVC hose from the packaging and note the compression nuts located on both ends of the tube.
- Thread one end onto the water shutoff valve, located in the wall behind your refrigerator. Use the wrench to tighten the bolt. ...
- Thread the other end of the PVA hose to the refrigerator connector. Again, use the wrench to tighten the bolt and wrap the coupling with tape.
- Turn the faucet to the “on” position. The water will rush up the back of the refrigerator in a loud “swoosh”, and then stop when it reaches the ...
- Decant a glass or two of water from the water dispenser in front of the refrigerator to clear the line of dust. ...
- Open the freezer door and set the ice maker toggle switch to the “on” position.
How to install your ice maker on the refrigerator?
refrigerator parts & water filters
- Your kitchen may already be plumbed for refrigerators with ice and water dispensers. ...
- If there isn’t an independent water supply line, you’ll have to use one that feeds the sink or dishwasher. ...
- If needed, plan for the water line to run through cabinets, above storage and behind drawers to prevent damage to the line.
How to hook up plastic water line to refrigerator?
Option 1 to Cap Off a Fridge Water Line
- Pull Fridge Out. Carefully pull the fridge out and away from the wall. ...
- Stop Water Flow. Now, you must stop the water flow so that you can work without making a wet mess. ...
- Remove Freezer Pipe. You must remove the freezer pipe to cap off the water supply line to your fridge. ...
- Install the Cap. ...
How much does it cost to hook up ice maker?
How much does it cost to hook up water to fridge? A typical water line usually averages $65-$130 to run the water line. To have a basic refrigerator installed on a first-floor kitchen with a water line ran to the refrigerator averages about $250.
How to hook up a water line to your refrigerator?
You'll need to make sure you have on hand:
- Enough copper piping to reach from the refrigerator to the closest and most convenient cold water source
- A T-fitting, which you can install in the cold water line to make a split that will feed to the refrigerator
- The connection piece that will link the copper tubing to the inlet to the refrigerator
Do you need a water line for ice maker in fridge?
If your fridge does not have a water/ice dispenser or don't plan to use it, you won't need a water line. You can also find refrigerators that dispense water from a tank, and similarly, require no plumbing. However, if you want a standard, plumbed ice maker, then, yes, your refrigerator will need a water line.
How do you hook up ice and water to a refrigerator?
3:024:03How to Connect a Refrigerator Water and Ice Dispenser | This Old HouseYouTubeStart of suggested clipEnd of suggested clipMake the nut hand tight two wrenches i want you to hold back right there okay i'll hold back rightMoreMake the nut hand tight two wrenches i want you to hold back right there okay i'll hold back right here. You don't want to over tighten but it wants to be nice and snug. There we go.
Can you add an ice maker to any refrigerator?
You can only install an ice maker on an appliance that is configured to accept this accessory—including the mounting holes in the freezer compartment, inlet ports for water lines, and harnesses for electrical connections. Consult your appliance brochure to learn if your refrigerator can be fitted with an ice maker.
How do you connect an ice maker line?
Unscrew the connector using locking pliers and purchase a cap or plug that will fit it. It's easy to install the cap — just screw it on. Once it's tight, turn on the water to make sure it doesn't leak, then turn the water off again, and you're ready to plug in the refrigerator and push it back against the wall.
How much does it cost to run a water line for an ice maker?
The cost for a plumber to install a water line for an ice maker is usually under $200.
How do I find the water line to my refrigerator?
InstructionsTurn off the Water. Locate the fixture shutoff valve on the cold water supply line under the kitchen sink. ... Disconnect the Faucet Water Line. ... Connect the Tee Adapter. ... Connect the Faucet and Refrigerator Supply Tubes. ... Connect the Supply Tube to the Refrigerator. ... Turn on the Water.
How much do ice makers cost for refrigerators?
Replacing a standard freezer-based ice maker costs $50 to $150, though you'll also pay for an hour or so of labor, bringing the entire replacement price up to $100 to $400.
How much is an ice maker for refrigerator?
The cost to replace a refrigerator's ice maker is around $300 to $450 for the replacement unit and labor costs of hiring a local refrigerator repair specialist.
How do I install an ice maker outlet box?
0:131:13How To Install Ice Maker Outlet Boxes | SharkBite - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst attach the mounting brackets to the studs with screws or nails at your desired height. This isMoreFirst attach the mounting brackets to the studs with screws or nails at your desired height. This is typically 18 inches from the floor to the top of the outlet.
How do you hook up a Frigidaire refrigerator ice maker?
0:191:21How to Hook Up Ice Maker on your New Refrigerator - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou need either one or two tools crescent wrench or just regular pliers. I like to use a crescentMoreYou need either one or two tools crescent wrench or just regular pliers. I like to use a crescent wrench or adjustable wrench. Now this is the water line hose.
How do I hook up the water line to my Frigidaire refrigerator?
0:041:49Refrigeration Water Supply Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn the refrigerator remove the cap on the water valve. Take the other end of the supply line andMoreOn the refrigerator remove the cap on the water valve. Take the other end of the supply line and install it onto the water valve to tighten it turn it a quarter to a half inch. Do. Not over tighten.
How much does it cost to install a water line for a refrigerator?
Refrigerator Water Line Installation Cost The price to install a water line ranges from $70 to $130. However, if your new fridge doesn't have an ice maker or water dispenser, you can skip this step. You also won't need a water line if the model you're replacing already had an ice and water dispenser.
How to install a water inlet tube on a refrigerator?
On the back of the refrigerator, locate the sticker where the water inlet tube will be installed. It shows that you must cut an “X” through the sticker with a razor knife. Bend the sticker back into the opening and pull out the foam insulating plug. This is a temporary barrier between the cold freezer air and the room air. Simply pull it out to expose the hole.
What is included in an ice maker kit?
The ice maker kits sold by manufacturers include the ice maker unit, a water supply valve, and all the tubing and hardware required. Make sure to buy a kit that is specified for your refrigerator model.
How to attach plastic tubing to a fill tube?
Attach the plastic tubing by screwing the end connector onto the threaded fitting at the end of the fill tube. Using pliers, tighten the compression nut securely, but don’t over-tighten, as this can damage the plastic fitting. The rest of the tubing should be unrolled and left hanging towards the floor.
Can you put your hands in an ice maker?
As you're working, take care to not place your hands in the ice maker's moving parts, particularly once the ice maker is connected to power. Even when they aren't moving, these edges can cut and even result in serious injury.
Can you replace an ice maker that has failed?
The same process can be used should you ever need to replace an ice maker that has failed. You can only install an ice maker on an appliance that is configured to accept this accessory—including the mounting holes in the freezer compartment, inlet ports for water lines, and harnesses for electrical connections.
How does an ice maker work?
It is fed by a small tube that runs up the back of the refrigerator to an inlet valve. When the refrigerator senses that more ice cubes need to be made, the inlet valve opens and lets water flow into a special ice cube mold.
How to connect a refrigerator to a water shutoff valve?
Step 2: Remove the PVC hose from the packaging and note the compression nuts located on both ends of the tube . Step 3: Thread one end onto the water shutoff valve, ...
How long does it take for an ice maker to work?
It’s really that simple. For most models, it takes at least an hour before the ice maker cranks into action and starts to spit out ice cubes. If the ice maker isn’t working, retrace your steps to make sure that there isn’t a kink in the line or that you’ve forgotten to turn on the water valve.
Do refrigerators have ice makers?
New refrigerators with ice maker units usually don’t come packaged with all the necessary supplies and parts to hook up the ice maker. Rather than going to a Big Box Home Improvement store, visit your local hardware shop instead where knowledgeable clerks can look at your refrigerator’s installation manual, and tell you what parts you will need.
