Use screws 1 inch longer than the width of the extension strips. Cut ¼-inch round over hardwood molding, ¾ inch wide to fit the front lip of each step and nail it to the lip of the step with pin nails to cover the screw heads. This process will extend your stair treads 1 inch.
Full Answer
How do you make a stair tread deeper?
Making Stair Treads Deeper Step 1. Chisel off the nosing of the existing treads so that each tread does not protrude beyond the riser board. Step 2. Measure the existing treads and cut new boards for each tread. Include the nosing of the tread in your... Step 3. Spread construction adhesive evenly ...
How do you measure for new stair treads?
Measure the nosing depth of the new treads. If the depth is greater than 1 1/2 inches, you must add new risers to the staircase. Measure the height and width of the existing risers. Cut new boards for each new riser.
How do you extend the length of a stair step?
Cut ¼-inch round over hardwood molding, ¾ inch wide to fit the front lip of each step and nail it to the lip of the step with pin nails to cover the screw heads. This process will extend your stair treads 1 inch. Mark Morris started writing professionally in 1995.
How far should a stair tread overhang the riser?
The stair tread overhang must project past the edge of the riser or over the step below by 3/4″ to 1-1/4”. An overhanging is not necessary for treads 11-inches or greater in depth.
How to get more tread on stairs?
How to Get More Stair Tread Width. Narrow stair treads are all too common, especially on steep staircases that already hard enough to ascend. You can make them a bit safer by adding a stair-nose to the front edge. You can gain up to 1 1/4 inches of stair tread, and even though that might not seem much, you'll be surprised at how much ...
How to install bullnose edging?
If you're handy with a miter saw, you can still install a bullnose edging for more tread width. Start out using a scrap piece of bullnose. Set the miter saw at about 8 degrees. Cut a handful of the bullnose pieces about 2-inches long and begin placing them around the curve.
How to attach bullnose to tread?
Cut the bullnose to length using a miter saw. You have two choices for attaching the bullnose to the tread. You can use nails or screws. Ether way, you should pre-drill through it first. Glue is also an approriate method for installing it.
How deep should stair treads be?
Another regulation requires that overall tread depth be no less than 10 inches. Stair nosing almost always has a rounded front called a bullnose that rolls from top to bottom on one side. If your treads do not have one, you can install one yourself to add width to the tread. You can purchase them already rounded with the bullnose, ...
What is a stair nose?
It consists of a 1- to-1 1/4-inch-wide piece of hardwood molding, usually red oak, that you nail or screw to the front edge of the stair tread. According to code, nosing must be at least 3/4 inch but not greater than 1 1/4 inches where existing tread depth is less than 11 inches.
How to check if a mitered edge is too steep?
Hold them in place with tape if needed and check the gap between pieces. If the gap is wider on the front edge the angle is too steep, subtract one degree and cut more pieces. If it's wider at the back edge add a degree to the miter saw. Cut and fit the test pieces until the mitered edges fit together tight.
Where does carpet come loose?
Carpet comes loose. It's usually fastened to the front edge under the lip or the riser on the lower step. It may be glued on or nailed on, either way it comes loose the same way. Pull it loose in one corner and pull it up just far enough to gain access to the front of the tread.