How To Install Compression Fittings On Copper Plumbing Pipes
- Clean the end of the copper plumbing pipe You should begin installing compression fittings on copper plumbing by using the emery cloth to clean the end of the copper pipe. ...
- Attach the compression nut and slide the ring onto the copper plumbing pipe ...
- Slide the nut and the ring toward the compression fitting ...
- Tighten the nut onto the fitting ...
How do you attach a compression valve to a water pipe?
Next, slide the valve onto the water pipe, making sure the pipe is fully seated into the valve's socket. Slide the compression ring and nut up against the bottom of the valve and thread the compression nut onto the valve body. Tighten the nut as far as it will go by hand.
How do you replace a compression valve on a hot water heater?
Slide the valve body off the end of the water pipe, then slide the brass compression ring and compression nut off the pipe. While the compression nut and ring could be reused with the new valve, it is better practice to remove these and install the new ones included with the new valve.
How do you put a compression ring on a pipe?
Before you fit the parts together, you slide a compression nut and a compression ring onto the end of the pipe. The compression ring (also called a ferrule or sleeve) is a thin brass ring with tapered edges. Once the pipe and fitting are together, you slide the ring against the fitting, then thread the nut onto the fitting.
How do you attach a compression nut to a pipe?
Slip the compression nut from the compression fitting onto the pipe, then slip on the compression ring. Slide both pieces down so they are 1 inch or so from the end of the pipe. Fit the compression fitting onto the pipe (or fit the pipe into the fitting, as applicable) until the pipe stops inside the fitting.
How do you install a compression shut off valve on a copper pipe?
0:491:32Compression Shut Off Valve | Quick Tips for Beginners - YouTubeYouTubeStart of suggested clipEnd of suggested clipThen what you do is make sure the valve is facing the right. Direction. Slide on the nut. Slide onMoreThen what you do is make sure the valve is facing the right. Direction. Slide on the nut. Slide on the valve mark the location. And then slide your ferrule.
How do you install a copper compression valve?
2:014:10How To Install a BrassCraft® Compression Valve - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext using the attached deburring tool insert the tool inside the copper tube apply pressure andMoreNext using the attached deburring tool insert the tool inside the copper tube apply pressure and rotate the tool several times to remove the sharp edge inside the copper. Tube.
Can you use a compression valve on copper pipe?
Compression fittings in the world of plumbing are very common. They are a safe way to connect copper pipe without the use of heat making them popular with DIY'ers. Many different types of valves, tees, connectors and utilities require compression fittings in order to make them water tight and safe.
How do you put a compression ring on a copper pipe?
0:152:08How To Install a Compression Fitting on Copper or Plastic TubingYouTubeStart of suggested clipEnd of suggested clipAnd slide it here with the threads facing our fitting. Then we're going to take this brass ring andMoreAnd slide it here with the threads facing our fitting. Then we're going to take this brass ring and slide it over the copper tube. Taking then the copper tube putting it to the back of the fitting.
How do you connect a valve to a copper pipe?
5:378:03How To Install A Water Shut off Valve On Copper Pipe - YouTubeYouTubeStart of suggested clipEnd of suggested clipDown until the top of the copper pipe bottoms out inside the new valve let's see how far down theMoreDown until the top of the copper pipe bottoms out inside the new valve let's see how far down the slides. Okay and now we'll just tighten up that valve. The nut on the valve.
Do you need to deburr copper pipe for compression fitting?
Do I need to deburr copper pipe? Deburring your copper pipes is essential for various reasons. Firstly, the sharp edges can damage seals or prevent joints from being watertight and secondly, the edges can create turbulence in the water pipe which leads to corrosion.
How reliable are compression fittings on copper pipe?
Although compression fittings are generally considered more reliable than threaded fittings, there are some potential problems. In general, compression fittings are not as resistant to vibration as soldered or welded fittings. Repeated bending may cause the ferrule to lose its grip on the tube.
Can you use compression fittings on copper gas lines?
Connections to steel pipe are made with an NPS threaded-to-flared copper adapter. Compression fittings in a gas piping system are not permitted unless allowed by the authority having jurisdiction.
Do you use Teflon tape on compression fittings?
On NEW compression fittings, PTFE tape is NOT REQUIRED although there are many people that still use it as an added layer of protection against leaks.
Why does my compression fitting keep leaking?
Over tightening a compression fitting can also cause the fitting to leak. When tightening up the compression fitting, only turn your tool until you feel resistance. From there, you shouldn't turn it anymore than a half a turn. By doing this, you can ensure you'll prevent your compression fitting from leaking.
How do you stop a compression valve from leaking?
Tighten compression fittings firmly with two wrenches to crimp the ferrule onto the pipe (Photo 3). Also make sure the pipe or tube goes straight into the fitting. Misalignment will cause a leak. If the fitting leaks after you turn on the water, try tightening the nut an additional one-quarter turn.
How do you fit copper compression fittings?
0:522:50How to install a COMPRESSION fitting! | GOT2LEARN - YouTubeYouTubeStart of suggested clipEnd of suggested clipApply a bit of flux on it it'll disappear with a couple of strokes. Make sure to wipe off any excessMoreApply a bit of flux on it it'll disappear with a couple of strokes. Make sure to wipe off any excess flux. Or it'll heat up your pipe. If you do however have a kink in your pipe.
Which way does a compression sleeve go?
1:186:41How to Use Compression Fittings - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you want to put your sleeve on and you're going to slide it down making be sure not to mess. UpMoreAnd you want to put your sleeve on and you're going to slide it down making be sure not to mess. Up the sides of the other sleeve.
How do you install an irrigation compression fitting?
0:301:46How to install a compression coupling for 620 raindrip tubing C620YouTubeStart of suggested clipEnd of suggested clipMake a straight cut across the pipe to ensure a tight. Fit insert your drip tubing into one end ofMoreMake a straight cut across the pipe to ensure a tight. Fit insert your drip tubing into one end of the compression coupler. And press inward rocking. The pipe and fitting back and forth.
How do you install a copper union fitting?
1:054:24Installing Union Fittings - YouTubeYouTubeStart of suggested clipEnd of suggested clipSlide the nut unto the tailpiece end of the Union. Make sure to do this before soldering slide theMoreSlide the nut unto the tailpiece end of the Union. Make sure to do this before soldering slide the ends of each piece of pipe into the ends of the Union fitting.
How to install a compression fitting on a pipe?
Slip the compression nut from the compression fitting onto the pipe, then slip on the compression ring. Slide both pieces down so they are 1 inch or so from the end of the pipe. Fit the compression fitting onto the pipe (or fit the pipe into the fitting, as applicable) until the pipe stops inside the fitting.
How to check if a compression fitting is leaking?
Check the compression fitting for leaks after you've completed all of the other plumbing connections and turned on the water supply to the pipe. If the compression fitting leaks, use both wrenches to tighten the compression nut gently until the leak stops.
How to cut a pipe?
Cut the end of the pipe, if necessary, using a tubing cutter. Open the jaws of the tubing cutter and fit it onto the pipe so the pipe rests squarely against the two flat rollers of the cutter. Tighten the cutter so the cutting wheel is snug against the pipe.
What is compression fitting?
A compression fitting is not a specific plumbing part but rather a type of fastening system for valves, water supply tubes and other plumbing fittings. The valve (or other part) has a port where the pipe slips in, and the port has male threads on the outside. Before you fit the parts together, you slide a compression nut ...
How to seal a pipe with a nut?
Once the pipe and fitting are together, you slide the ring against the fitting, then thread the nut onto the fitting. The nut compresses the ring between itself and the fitting, and the tapered edges of the ring are wedged tight inside the fitting and the nut, creating a watertight seal.
How to tighten compression nut?
Slide the nut over the ring and thread it onto the fitting until it is hand-tight. Be careful not to cross-thread the nut. Fit one wrench onto the body of the fitting and hold it so that the fitting doesn't move. Use another wrench to tighten the compression nut about one-half to three-quarters of a turn.
How to clean a pipe smooth?
Clean the outside of the pipe with a rag; it must be clean, with no paint or other contaminants. If necessary, apply a cleaner or solvent to the rag to clean the pipe .
How long does it take to add a compression shut off valve to copper?
In less than 5 minutes you’ll see the right way to add a compression shut off valve to copper…and without any leaks.
How to insert a valve in a pipe?
Slide the nut onto the pipe then insert the valve. Mark the valve location on the pipe with a marker to ensure it’s fully inserted.
How to tighten a ferrule on a shut off valve?
Use adjustable wrenches to turn the nut another 1/4 to 1/2 turn. This tightens the ferrule against the shut off valve and creates a watertight seal.
What is the best tool to cut copper?
The AutoCut tool is fantastic because it cuts copper quickly and leaves a square cut. Use emery cloth or pipe cleaning tools to clean paint, grease, or other contaminants off the surface of the pipe. Finally, deburr BOTH the inside and outside of copper pipes. This ensures the ferrule of the compression shut off valve will work properly.
What causes a compression valve to leak?
Furthermore, check the inside of the compression valve for any contaminants. Any debris, grease, or impediments in the valve can cause leaks.
Is it necessary to use Teflon tape for compression valves?
Compression valve installation isn’t rocket science. Don’t complicate it!! In addition, don’t use any type of Teflon tape or pipe dope. Both of these aren’t necessary because it’s the ferrule that makes the seal against the valve. This also highlights why it’s important to properly prep the pipe.
