The Delta sink stopper assembly is basically a simple lever. The lift rod, which usually sticks up from the rear of the faucet body, connects to a horizontal pivot rod by means of a flat, slotted bar called a clevis. The pivot rod extends into the drain tailpiece and through a hook on the bottom of the stopper.
How do you replace the stopper on a Delta pop up drain?
Replacement Delta stoppers are available, but the existing stopper must first be removed. Actuate the pop-up drain's trip lever to lift the stopper out of the drain pipe. Remove the screws that secure the cover plate assembly to the bathtub's wall, using the screwdriver. Pull the cover plate assembly out of the tub.
How does a bathroom sink drain stopper work?
For most bathroom sinks, the drain stopper apparatus is a pop-up assembly that works by means of a small vertical rod attached to a pivot rod below the sink. This lift rod slides up and down through a small hole in the back of the faucet body. The pivot rod moves a linkage inside the drain tailpiece, lifting or lowering the stopper as needed.
How do you attach a drain stopper to a pivot rod?
Tighten the screw on the connecting strap to secure it to the pivot rod. Connect the vertical strap to the horizontal pivot rod by threading the spring clip onto the rod; one end of the clip attaches on each side of the strap. Check to make sure that the pop-up stopper opens and closes fully inside the drain opening.
What is a drain stopper apparatus?
For most bathroom sinks, the drain stopper apparatus is a pop-up assembly that works by means of a small vertical rod attached to a pivot rod below the sink. This lift rod slides up and down through a small hole in the back of the faucet body.
How do you install a sink pop up drain stopper?
1:393:31How to Install a Pop-Up Drain in a Bathroom Sink | Repair and ReplaceYouTubeStart of suggested clipEnd of suggested clipPush the drain collar down into the hole any excess putty will be pushed out and can be easilyMorePush the drain collar down into the hole any excess putty will be pushed out and can be easily removed after the rest of the drain is installed slide the rubber gasket onto the shaft.
How do I remove a Delta drain stopper?
0:051:58Removing a Sink Drain Stopper to Unclog it - Mikes InventionsYouTubeStart of suggested clipEnd of suggested clipYou need to loosen the nut. So you can remove the rod and dust the stopper. This little clip at theMoreYou need to loosen the nut. So you can remove the rod and dust the stopper. This little clip at the end comes off when you pinch it and slide it off the end of the rod.
How do you install an overflow pop up drain?
5:5410:03How to replace a sink drain with push button stopper - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow we'll put these two pieces on from underneath. And go on um slanted side up the smaller. Side.MoreNow we'll put these two pieces on from underneath. And go on um slanted side up the smaller. Side. Up now the big nut. There spin it on with this this lip pressing up against the bottom of it.
How do I install a bathroom sink stopper?
2:554:21Replace a Bathroom Sink Stopper - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you turn it 90 degrees. And put the pivot rod through then it'll be removable and it'll raise upMoreIf you turn it 90 degrees. And put the pivot rod through then it'll be removable and it'll raise up and down by writing on top of the end of the pivot rod install the pivot rod into the drain. Body
How do I remove a lift and turn drain stopper?
0:462:14Removing a lift-&-turn stopper (1-step) - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut basically you'd grip it underneath that top part and just grip it tight turn it once he getsMoreBut basically you'd grip it underneath that top part and just grip it tight turn it once he gets loose. Enough. Just keep turning. And it comes out.
How do I install a Delta pop up assembly?
5:4812:21How to Install a Delta® Pop-Up Sink Drain - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd hand tighten the nut onto the drain body. And as I do this important note is we don't need toMoreAnd hand tighten the nut onto the drain body. And as I do this important note is we don't need to over tighten this we just want to be snug enough that it keeps the rod in place.
How do you install a pop up drain stopper in a bathtub?
2:2615:04How To Replace A Bathtub Drain - Remove and Install New ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe full metal that you have the end of method of the course metals. Okay now you put this one inMoreThe full metal that you have the end of method of the course metals. Okay now you put this one in one of the holes. Okay and now you really want to give it against the clock remember.
How does a pop up sink stopper work?
SO HOW DOES A SINK POP-UP MECHANISM WORK? It's actually a fairly simple design. When the lift rod is pulled upwards, it pulls the pivot rod up as well. This pivot rod is attached to the stopper, which is pulled down, effectively sealing the sink.
How do you remove a tub stopper without screws?
If there is no set screw on either the knob or the stopper, it likely uses a channel/pin mechanism. Lifting the stopper, slowly rotate it counter-clockwise, aligning the slot at the bottom of the channel with the pin on the strainer. Pull upwards to release the stopper.
How do you fix a Delta bathtub drain?
0:255:40How to Replace a Bathtub Drain - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's a little hole on the slot put your flathead through there's a little bit of extra leverageMoreThere's a little hole on the slot put your flathead through there's a little bit of extra leverage you turn it you'll notice that it starts to come undone pretty good. Once you get her rolling.
How to tighten a drain nut?
Tighten the mounting nut with channel-type pliers while continuing to hold the tailpiece in place. Do not over-tighten this nut, but make sure it is secure enough so that the drain assembly does not spin in the drain opening.
How does a drain stopper work?
For most bathroom sinks, the drain stopper apparatus is a pop-up assembly that works by means of a small vertical rod attached to a pivot rod below the sink. This lift rod slides up and down through a small hole in the back of the faucet body. The pivot rod moves a linkage inside the drain tailpiece, lifting or lowering the stopper as needed.
Why is my pop up assembly hard to move?
If the pop-up assembly is hard to move when you move the pivot rod, it's likely that the pivot rod nut has been tightened down too much and needs to be slightly loosened.
What to use on a pop up sink?
If you do not have plumber's putty or cannot use it on your type of sink, then you can use silicone caulk. Some pop-up assemblies come with a foam or rubber gasket to use in place of plumber's putty or caulk.
Where to insert pivot rod in drain?
Insert the pivot rod into the opening in the side of the tailpiece from under the sink. Usually, there is a plastic washer on each side of the plastic ball. You should be able to feel the tip of the pivot rod slide through the opening in the stopper linkage inside the drain assembly.
How to connect a vertical strap to a horizontal pivot rod?
Connect the vertical strap to the horizontal pivot rod by threading the spring clip onto the rod; one end of the clip attaches on each side of the strap.
What to use in place of plumber's putty?
Some pop-up assemblies come with a foam or rubber gasket to use in place of plumber's putty or caulk. Scoop out a ball of plumber's putty and roll it in your hand to form a long rope, then lay the rope around the edge of the drain ring. Aaron Stickley.
How to tighten a pivot rod?
Feed the pivot nut over the pivot rod and tighten it onto the pipe stub. Tighten the nut by hand onto the threads on the end of the tailpipe's horizontal stub. If you overtighten the nut, the pivot rod may not be able to move up and down freely — test the rod's movement, and loosen the nut slightly if necessary.
How to loosen a PVC tailpipe?
If your trap is PVC, the connector will be a PVC compression nut that you can loosen by hand. If the trap is metal, it will be a metal nut that requires a large wrench or channel locks to loosen. In either case, loosen the nut completely so that the two sections of pipe are disconnected.
How to remove pivot rod from drain?
The pivot nut is threaded onto a short stub on the drainpipe, and is the entry point for the pivot rod into the drain. Turn the nut counterclockwise by hand — or use a wrench if necessary — to unthread it. Pull it straight off along with the inserted pivot rod. You should now see the pivot ball nestled inside the nut, along with the stub of the pivot rod that connects to the stopper inside the pipe.
What to do if your sink drain kit has a metal tailpipe?
If your sink drain kit has a metal tailpipe, the exposed threads may be on the tailpipe instead of the sink drain. If so, smear the pipe joint compound on the exposed tailpipe threads instead.
How to make a sink ring?
Then, roll it into a “snake” about the thickness of a pencil, and form a ring by pressing the ends together. Press this ring onto the rim of the opening in your sink basin.
How to install a plastic washer on a car?
Insert the tapered plastic washer into the horizontal stub on the tailpipe. Your kit will come with a small plastic ring that is slightly wider in diameter on one side than the other. Place the narrower side into the opening first. This washer will help hold the ball on the pivot rod in place and provide a watertight seal.
Where to put gaskets on sink?
Stack any included gaskets on top of the locknut or bell housing. Without these one or more gaskets that came with the kit, you'll have a metal-to-metal compression connection under the sink that won't be watertight. Follow the provided product instructions regarding the order and placement of the gasket (s), then put them on top of the locknut or bell housing before you slip it over the threads of the sink drain's bottom.
Why does my Delta tub fill with water?
When the trip lever is engaged, the tub fills with water because the stopper has closed off the drain pipe. It is for this reason that a broken stopper will cause the tub to slowly lose water. Replacement Delta stoppers are available, but the existing stopper must first be ...
How to release drain stopper?
Pull the pin securing the stopper to the end of the linkage out of the stopper with pliers. This will release the drain stopper.
What causes a bathtub to lose water?
If the bathtub slowly loses water, a damaged drain stopper may be the problem.
Who is John Stevens?
John Stevens. John Stevens has been a writer for various websites since 2008. He holds an Associate of Science in administration of justice from Riverside Community College, a Bachelor of Arts in criminal justice from California State University, San Bernardino, and a Juris Doctor from Whittier Law School.
