How to Install a Marble Fireplace Surround
- Step 1 - Plan and Measure Take careful measurements of the area where the marble fireplace surround will be installed. ...
- Step 2 - Prepare Surfaces for Marble Check all areas of construction to insure that they are flat and level. ...
- Step 3 - Dry Fit Design ...
- Step 4 - Apply Thinset and Marble ...
- Step 5 - Seal and Grout ...
Full Answer
How are marble fireplaces attached to the wall?
A coat of adhesive should also be applied to the back edges of the legs which will be in contact with the wall to aid in the securing of these components. The legs are now ready to be lifted and secured on to the wall brackets. Carefully place the marble or limestone back panel in to position and secure with adhesive.
How do you secure a marble fireplace?
Ideally, the hearth should be secured to the floor. This can be done best with tile adhesive or cement. Spread the mixture of your choice along the bottom edges of the supports and risers underneath your hearth and lay it on the floor. Time for a spirit level!
How is a fireplace surround attached to the wall?
Many modern fire surrounds use a hidden fireplace fitting bracket. One bracket is fit to the wall, while a corresponding second bracket is screwed to the fire surround. They then simply slip together without the need for any messy looking screws around the edges.
How do you secure a marble mantel?
Place a bead of construction adhesive on the back of one mantel leg, then position it in place, and secure it using a metal strap or angle bracket. You will likely need to brace it to hold it in position while the adhesive dries.
What kind of adhesive is used in installing marble?
Cementitious tile glues are suitable for most marble tiling applications, horizontal and vertical. Nevertheless, when the tiling is likely to be subject to temperature extremes or fluctuation, a slightly more expensive construction epoxy should be considered.
Do you need special thinset for marble?
Things You'll Need For marble tiles, the adhesive of choice is often a cement-based thinset. It bonds well with concrete, backer board or wooden subsurface, while allowing the tile flexibility to move along with the surface beneath.
Do you need special mortar for fireplace surround?
The major difference in tiling a fireplace compared to other surfaces is the type of mortar required. Use heat-resistant epoxy (up to 400 degrees F) when tiling over wood; use heat-resistant cement-based mortars on masonry surfaces. If a brick surround and hearth are stable and in good repair, you can tile over them.
How do you mount a fireplace surround?
2:073:17Builders Choice Fireplace Leg, Skirt and Mantel Install - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe preassembled base corner blocks to the bottom of each leg using construction adhesive andMoreThe preassembled base corner blocks to the bottom of each leg using construction adhesive and finished nails be sure to pre-drill any nail holes fill. The nail holes with matching wood filler.
Can you glue a fire surround to a wall?
A new super strength adhesive proves its mettle. CT1's Power Grab n Bond provides a real alternative to traditional methods for fitting wooden fire surrounds. No more drilling, dust, holes and screws with an amazing solvent free bonding agent that effectively replaces the tiresome old procedure.
How do you seal marble edges?
InstructionsTest the Marble Sealer. Test a small amount of the marble sealer in an inconspicuous area to make sure the sealant will not discolor the stone. ... Apply the Marble Sealer. Apply the sealer to each tile individually, using a foam brush or soft cloth dipped in the sealer. ... Seal the Grout Joints. ... Apply a Second Coat.
How do you attach a stone mantel to the wall?
Drill holes through the cleat and into the fireplace using a masonry drill. Hammer the wedge anchors into the holes and then tighten them in place using a socket wrench. With the cleat secured to the fireplace, slide the mantel onto the cleat. Secure the mantel to the cleat using brass screws.
How far should a mantle stick out from the wall?
As a general rule, the mantel is placed about 12 inches above the fireplace opening. Then adding an inch to the distance for every inch that the mantel protrudes.
How do you secure a stone fireplace to the wall?
Typically, the fireplaces are set on top of a solid hearth, with either mortar or another bonding material acting as bedding between the stone components. Use mechanical fixings such as steel brackets, dowels, and screws to hold the components in position and secure them to the wall.
What adhesive can be used to bond marble to marble?
This Adhesive is perfect for bonding Marble to /marble wood. Polyfix Instant Adhesives is suitable for all works where a particular adhesion is required, but also provides all the other typical mastics features. Stone Adhesive is available in gel form for vertical & horizontal applications.
Will Gorilla glue hold marble?
The gap-filling, durable, 100% waterproof adhesive formula is perfect for indoor and outdoor projects, holds in 30 seconds, and bonds virtually anything including subfloor, mirrors, trim, drywall, landscaping, bath surrounds, foamboard, marble and more!
How do you secure a stone hearth?
Spread a thin bed of mortar underneath where the legs go. Place the legs in their position and attach them using the braces, fasteners, screws and a drill. Apply a thin layer of mortar to the tops of the stone hearth legs. Place the mantel in position with a helper, and verify it is level using a carpenter's level.
How do I protect a metal fireplace?
Be sure to tape off and protect the metal and glass fireplace. I did not tape and protect mine enough and now I’m regretting it. Use a plastic bag or craft paper. Whatever you use, just tape it all off! Mortar and grout will drip and ruin the metal and glass if you don’t.
How long does it take for a haze to appear on a tile floor?
After a few hours a haze on the tile will appear. Buff all of it off with a soft clean cloth.
Do you need to seal white marble?
After tiling is done, you MUST seal the marble. Buy a sealer that specifically mentions white marble. Some sealers will totally change the color of your marble, so do your due diligence in research. Like I said before, white marble is very absorbent and will take on the color of your thinset, your grout and your sealer.
Can you seal white marble after tiling?
Mortar and grout will drip and ruin the metal and glass if you don’t. Those wires you see sticking out of the wall is where the mantel will be and where the cable and electric outlets will be built in. After tiling is done, you MUST seal the marble. Buy a sealer that specifically mentions white marble.
Is marble herringbone tile hot?
Marble herringbone tile is so very hot right now. Marble is a classic choice for a fireplace surround and hearth regardless, but adding in the texture of herringbone is a nice modern and updated twist on the tried and true classic. I bought my 12×12″ marble herringbone, mesh-backed tile from Lowes. It was from their Allen + Roth collection – ...
Can you cut marble tile with a wet saw?
Cutting marble tile requires a wet saw. I LOVE WET SAWS! Please do not be scared by these. You can rent them from the big box home improvement stores and they are made for the DIY-er. I chose the smallest wet saw they had and rented it for a day (ie: have your plan ready to execute, especially if you are renting by the day).
Is marble tile the same as grout?
Well marble tile is the same. Follow the manufacturer’s instructions for how long the thinset needs to set before grouting. I have used several brands of grout before and I tried a new one. And I will be totally honest, I don’t necessarily recommend the brand I used because it dried too fast.
How to lay marble slabs on a hearth?
With your strongest assistant, lift and carry the marble slab to the hearth. Lay it slowly and gently onto the white mortar, checking that it is correctly positioned horizontally, front to rear, and on the diagonal. You will only have a few moments to adjust it before the white mortar firms and fastens it in place.
How to keep marble from sinking in leveling compound?
Use the adhesive spreader to put a 1/4 inch layer of thinset adhesive on top the leveling compound. This will help the marble adhere and keep it from sinking into the leveling compound.
What to use to remove hearth?
With the pry bar, sledgehammer and chisel, remove the existing hearth. With assistants, carry the old hearth materials outside for disposal or cleaning and reuse.
Can you put a marble hearth in a fireplace?
When you want to upgrade your fireplace, installing a marble hearth and surround will add graceful charm to your home. In Part 1, the marble floor is installed. Follow the procedure below to enhance your fireplace with a marble hearth.
Step 1 – Start with your hearth
When installing your hearth, we recommend the use of Micore board (may be purchased from us) or a similar product to create a buffer between the hearth and floor. This helps in preventing your hearth from breaking once installed, as well as providing additional flame retardance.
Step 2 - Prepare and install your facing legs
Measure for the legs, and check both sides of the firebox; it may be necessary to cut the legs two different lengths (Mantels Direct is happy to cut your fireplace surround facing kit for a nominal fee, if one of our standard sizes does not meet your needs) Cut the legs as required.
Step 3 – Install your facing header and optional riser
One must use their own judgment at this point, sometimes it may look better on the firebox for the header to follow the box, even if it's not level. Apply adhesive on the back of the header and place into position.
How many sections are there in a marble fire surround?
The below article will examine how to install a marble fire surround: 1. Typically marble fire surrounds are supplied in 5-6 sections depending on the design you select: (a) Hearth (base section of fire surround) (b) Back Panel (section where fire is recessed)
Do you check the pieces of a fire surround before installing?
1. We strongly recommend you check each piece of the fire surround prior to installation
What is the best adhesive for fire surrounds?
Silicon is a very flexible adhesive that is ideal for use to secure the various sections of the fire surround. Essentially the main advantage of using silicon over a more permanent and harsh adhesive (such as ‘no nails’) is that silicon can be removed at a later stage if it is not needed.
What is the section 1 of the fireplace?
Section 1: The hearth (base of fireplace),
Can you break the silicon seal on a fireplace mantle?
Example: If you stick the mantle (top shelf of fireplace) to the body of the fire surround using silicon and have a problem with the down lights in the future, then you can break the silicon seal and remove the mantle to access the electrical parts. If your fireplace mantle was stuck down with an alternative adhesive, then this would not really be possible and be a major hindrance.
