- Mark and Measure the Borders. First, you need to place a mark on your borders to properly measure how much metal edging you need. ...
- Dig a Trench. Our experts recommend digging a trench so you can place your metal edging properly. ...
- Place the Stakes. When your metal edging comes with stakes, you need to strategically place these to ensure stability.
- Backfill. When your metal edgings are in place, it’s now time to refill both sides. ...
How do you install metal garden edging?
Installing metal garden edging is relatively easy since it sometimes just needs to be hammered into the ground. In other instances, it may require a bit more elbow grease or even specialized tools.
Can you Hammer metal garden edging?
Avoid using a regular hammer, since this can damage the metal edging. And if you have a hard time digging the trench, placing the edging or hammering in the stakes, moisten the soil as you are working. You can create boxes with the edging if you like; all you need to do is cut it into smaller pieces with a hacksaw.
How do you lay landscape edging on a trench?
Lay out your steel landscape edging roughly along your trenches. For curved or angled sections, it is best to assemble or bend the pieces ahead of time rather than trying to do it once it's in the trench. For straight sections, the edging can be assembled as it's placed in the ground, but you should still lay out enough along all of your edges.
What kind of tool do you use to install metal edging?
The slot or narrow trench required for metal edging installation is a lot narrower than needed for most other types of landscape edging since the spikes or posts that hold the metal in place install vertically rather than at an angle. This means a straight-edged garden spade or shovel is the perfect tool for the job.
How deep do you install metal edging?
Most metal edging is going to be deep enough to be installed 4-6 inches into the ground and still have a few inches above ground (with the exception of our Edge Right metal landscape edging that is 8 inches in depth—double that of most common metal edging).
How do you install aluminum garden edging?
3:384:45Permaloc Aluminum Landscape Edging Installation Instructions - HDYouTubeStart of suggested clipEnd of suggested clipSet a piece of wood or brick on top and bend the edging upward to the desired angle. At. The end ofMoreSet a piece of wood or brick on top and bend the edging upward to the desired angle. At. The end of the run cut the final section to the correct length using a hacksaw and drive the final stake.
How do you dig a trench for metal edging?
2:314:12How To Install Metal Landscape Edging. Metal Lawn ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipHow deep the trenches will depend on which size material you use we suggest digging half the widthMoreHow deep the trenches will depend on which size material you use we suggest digging half the width of the landscape edging you selected.
How do you install corrugated metal edging?
0:561:55How to Install Tuscan Path Metal Garden Edging - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst prepare the area by digging a level trench. The trench depth should be approximately half theMoreFirst prepare the area by digging a level trench. The trench depth should be approximately half the height of the edging. Once your trench is dug the next step is to unroll the edging.
How do you secure garden edging?
Steps1Dig trench for plastic edging. Dig a trench along your garden bed. ... 2Secure the edging with pegs. Once your edging in is the trench, peg it into the ground on the back. ... 3Measure and cut your corrugated edging. ... 4Secure your corrugated edging.
How do you cut metal garden edging?
8:5612:11Col-Met Steel Landscape Edging Installation and Tips - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhen cutting the edging make sure you have on safety glasses and gloves along with a saw with a goodMoreWhen cutting the edging make sure you have on safety glasses and gloves along with a saw with a good sharp metal blade lay. The edging flat to cut it. Don't cut from top to bottom.
How do you install metal landscape?
3:2210:35EASY LANDSCAPING IDEAS.. INSTALL METAL ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing a rubber mallet. And maybe. We can use the rubber mallet it may have to get a metal mallet I'mMoreUsing a rubber mallet. And maybe. We can use the rubber mallet it may have to get a metal mallet I'm not sure and you can use I have a sawzall to walk sawzall or reciprocating.
How do you install metal edging from Lowes?
0:093:57Colmet Installation How-To Guide - YouTubeYouTubeStart of suggested clipEnd of suggested clipOr simply pounding the edging down to its desired. Depth. If trenching consider using a sharpshooterMoreOr simply pounding the edging down to its desired. Depth. If trenching consider using a sharpshooter shovel or something like a half moon edger. Form your trench in the desired.
How do you straighten metal edging?
0:241:43How to bend thick EverEdge Steel lawn & landscape edging - YouTubeYouTubeStart of suggested clipEnd of suggested clipCheck yeah it looks close enough and now all i've got to do is press this down and push it down toMoreCheck yeah it looks close enough and now all i've got to do is press this down and push it down to 90 degrees let's hope for the best. We'll take it out. From. There these go a little bit more.
How do you install lawn edging?
Dig a trench along the edges of the bed with a round point shovel or spade, following the marking paint. Dig the trench to a uniform depth of three to four inches—deep enough to let the edging stand about one-half inch above ground level. Dig straight down to create a vertical "wall" that will support the edging.
How do you use galvanized lawn edging?
2:2310:03DIY Metal Lawn Edging Installation : CORE EDGE - YouTubeYouTubeStart of suggested clipEnd of suggested clipEdge i'm just running the half moon tool along the edge. And using a rocking motion removing any ofMoreEdge i'm just running the half moon tool along the edge. And using a rocking motion removing any of the debris. And leaving myself a clear edge.
How do you install aluminum paver edging?
0:311:17StructurEdge Install - YouTubeYouTubeStart of suggested clipEnd of suggested clipInto the channel along the top of the edging spanning both pieces spike the edging into place withMoreInto the channel along the top of the edging spanning both pieces spike the edging into place with ten inch spiral steel spikes every one foot on center also spike the end of each edging.
How do you hammer in metal edging?
0:232:01How to Install EdgeRight Metal Edging - YouTubeYouTubeStart of suggested clipEnd of suggested clipPlace the block on the spine begin to tap in with a hammer. It's best to hit in the middle to avoidMorePlace the block on the spine begin to tap in with a hammer. It's best to hit in the middle to avoid see-sawing use repetitive strikes in alternating positions until metal is that desired depth.
Is aluminum edging good?
As for aluminum landscape edging: Aluminum is flexible and resilient, allowing for smoother curves as well as straight lines. Aluminum is strong, withstanding years of maintenance. It has excellent resistance to corrosion. It will never crack, rust or become brittle.
How do I install Easy Flex edging?
1:042:43EasyFlex No-Dig Edging - Improvements Catalog - YouTubeYouTubeStart of suggested clipEnd of suggested clipPlace under edging prior to spiking. Next hammer the included anchoring spikes through the tabs toMorePlace under edging prior to spiking. Next hammer the included anchoring spikes through the tabs to hold the edging in place.
How to secure a metal post to a post?
Tap any connector sleeves fully into place. If you are using an edging that requires a wooden stake behind each overlap, tap those into place behind the overlapped area and then secure the metal to the post using the screws recommended by the edging company. This may vary depending on the metal product.
How to tamp down dirt on flower bed?
Push any loose dirt into the trench on the flower bed (back) side of the edging. Tamp down the dirt by walking so your weight falls with one foot on the front side of the edging and one foot on the back of the edging. Pack down the dirt this way along the entire length of the edging.
How to measure for edging?
For each area you plan to edge, stretch the twine as an outline from the starting point to the ending point of the area you want to edge. The twine should sit exactly where the edging will go. Straighten and measure each length of twine, add up the total length and then add at least another foot or so to account for overlaps, which vary depending on the style of the edging you'll use. All metal edging can be cut to length with a hacksaw, tin snips or a similar tool, so keeping a little extra on hand is a good idea in case you ever want to replace a portion.
How much corrugated steel sticks out of the ground?
How much corrugated steel sticks out of the ground is entirely up to you as long as at least 1/3 of the total height is below ground. For this reason, it could do a better job holding mulch or other landscaping materials in the garden bed, as many other forms of metal edging are designed to sit nearly flush with the ground.
What is the best tool for cutting a metal step?
This means a straight-edged garden spade or shovel is the perfect tool for the job. Insert the spade vertically into the soil where you wish to cut a slot for the edging and push down on the metal step with your shoe, putting your weight on the step.
What is metal edging?
Metal landscape edging stands out among common forms of edging as far as its overall appearance, longevity and durability are concerned. Clean, straight lines and moderate curves are possible with metal lawn edging depending on the thickness of the edging and its composition. Some forms are also a little easier to install in your garden ...
What is the bottom edge of a trench?
If the bottom has teeth or spikes in it, the bottom edge is obvious, but if not, the bottom edge is likely just a straight piece of metal without a rolled edge on top . If the edging has a front and back side, make sure every piece is facing the proper direction.
How to lay out landscape edging?
For curved or angled sections, it is best to assemble or bend the pieces ahead of time rather than trying to do it once it's in the trench. For straight sections, the edging can be assembled as it's placed in the ground, but you should still lay out enough along all of your edges. This will further ensure that you have what you need to complete your edging project .
What is steel edging?
Adding steel landscape edging not only organizes your lawn visually , but is also a very practical way to set up your landscape design. It can be installed along any driveway, path, flowerbed or garden to create a neat and well-defined edge that makes landscape upkeep a much easier job.
How tall should a raised garden be?
For something like a raised garden, you may want it to sit 4 or 5 inches above ground, or you may want it only a half inch above ground so that it doesn’t interfere with the lawnmower.
How to protect a stake from warping?
Either way, place a block of wood over the stake and pound it with a hammer or mallet. This will protect from accidentally damaging or warping the edging.
Can you cut through steel edging?
In assembling curved sections and corners, or even with straight edges at odd lengths, it may become necessary to adjust the length of a section of edging to properly fit the trench. If this must be done, you can cut through your steel edging with a hacksaw.
Do you need to measure for steel edging?
You’ll need to plan and measure to know how much steel landscape edging is needed for the job. If placing your landscape edging around an established landscape feature (such as a garden or path), you need only measure along the edges.
How to make a trench for edging?
Make a narrow trench where the edging will go using a sharp spade. Push the spade into the soil about 6 inches, wiggle it back and forth a couple of times and pull it out. Do not leave any part of the edge uncut.
What kind of edging is used for a fence?
The experts at Country Living list many other kinds of edging materials, starting with plastic. While not elegant, it's inexpensive and easy to install. Decorative edging fences also look nice and are available in metal, plastic or wood. Some homeowners like the look of small cedar shingles and cedar shake “fences,” which can be hammered into the ground. These are easily damaged though and usually won’t last more than a few years. Landscape timbers are also nice (and inexpensive), but look for those that are pressure-treated for enhanced rot resistance.
What to use for a backfill?
Once you have finished placing your stakes, you'll need to backfill against the edging on both sides. You can use topsoil or mulch for this, but a dense material will work best. Pea gravel or other small stones can make a good base for your backfill. If you want the aesthetic appeal of a freshly mulched garden bed, you can always add mulch atop a bed of stones or gravel.
What is metal edging?
Metal edging creates a clean-cut, professional-looking edge to a lawn, flowerbed or gravel yard. It helps contain and separate plants, mulch and gravel. Metal edging is slightly more expensive than plastic edging, but it lasts longer.
How to sink stakes in a garden?
If stakes came with the edging, use a rubber mallet to sink each stake, placing them either equidistant from others, or around pressure areas such as corners or uneven ground. Note that stake placement is important for the stability of your edging and its ability to remain in one place.
Where to put vinyl trip cap?
Use a vinyl trip cap on top of the edging around swimming pools, playgrounds and other areas where children might be playing.
Can you use a regular hammer to cut metal edging?
Avoid using a regular hammer, since this can damage the metal edging. And if you have a hard time digging the trench, placing the edging or hammering in the stakes, moisten the soil as you are working. You can create boxes with the edging if you like; all you need to do is cut it into smaller pieces with a hacksaw. Just make sure that the corners line up well.
