Installing Correctly
- 1 Measure for the height of the rod. Use a measuring tape. ...
- 2 Mark where the brackets will go. ...
- 3 Add a mid brace if needed. ...
- 4 Drill pilot holes to help start the screws. ...
- 5 Screw the brackets to the casing or wall. ...
- 6 Check for level. ...
- 7 Put the curtains on. ...
How high should you mount a shower curtain rod?
While there is not an exact height where you should hang a shower curtain, there are several things to consider -- depending on what look you are trying to achieve -- when installing a shower curtain rod. A standard shower curtain is typically 72 inches long, so the curtain rod should be installed around 75 to 77 inches from the floor.
How to install a hookless shower curtain?
- Measure up from the corners of the bathtub along the side where you want to hang your curtain.
- Run the tape measure from one marked point to the other and check the tape with a level to make sure your marks are level.
- Screw a hook eye screw into each of the two marked points.
How do you hang a shower curtain rod?
Steps of How to Hang a Shower Curtain Rod
- Know the Dimensions of the Curtain to be Installed. Usually, bathroom curtains in the market have standardized dimensions. ...
- Determine the Installation Height. According to international standards, the bottom edge of any shower curtain should be 5 cm above the shower floor.
- Install Supports, Rod and Curtains. ...
How do you install a curved shower rod?
Method 1 Method 1 of 2: Adhering to General Rules Download Article
- Select a rod that matches the rest of your bathroom fixtures. ...
- Position the shower rod high enough that you won't bump your head. ...
- Place the shower rod at least 74 inches (188 cm) above the shower floor. ...
- Cut your rod if necessary. ...
How much does it cost to install a shower rod?
How long does it take to install a tension shower rod?
How to extend a rod on a wall?
How to tighten a rod?
What is tension rod?
Can you slide a shower curtain through a rod?
Do shower curtains come with screws?
See 4 more
About this website
How do you hang a round curtain rod?
1:013:21How to install a curved shower rod - simple instructions - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you need to use a screw anchor then i would measure the depth. And the height of where your screwMoreIf you need to use a screw anchor then i would measure the depth. And the height of where your screw hole starts and make sure to do that to the other side drill your holes. And tap in any anchors.
How do you use a curved shower rod?
0:070:56The Gripper Easy Install Adjustable Curved Shower Rod at Bed Bath ...YouTubeStart of suggested clipEnd of suggested clipNo drilling or difficult installation simply measure the width of your shower. And adjust the rodsMoreNo drilling or difficult installation simply measure the width of your shower. And adjust the rods to the same width tighten the screws.
Where do you mount a curved shower rod?
The midpoint of the rod should extend several inches past the outside rim of the tub. Depending upon tub model, mount rod between 6" and 8" from center line of the tub. The middle portion of the rod should curve just outside the contour of the tub.
How do you unlock a curved shower curtain rod?
Grasp the shower rod and the bracket and push them up along the wall until they both are free. Some curved rods have a telescoping action so you can simply slide them back on themselves to detach them from the wall.
How do you install a curved fiberglass shower rod?
Mounting Shower Curtain Rods to Fiberglass Shower SurroundsMeasure the height of your shower curtain. ... Remove the shower curtain rod. ... Press a drill with a brad-point bit against the first mark. ... Slide a toggle bolt into each screw hole on one end of the curtain rod. ... Ask a friend to hold the curtain rod in place.More items...
Does a regular shower curtain fit a curved rod?
And despite what some people say, you do not need to buy a special shower curtain for a curved shower rod. Just like with traditional straight rods, you will need an extra long shower curtain if you install the curved shower rod high on the shower walls and close to the ceiling.
How do I keep my shower curtain rod from falling down?
1) Create More Friction The caps on tension rods are often made of plastic, but even rubber ones are so incompressible that moist, smooth surfaces such as tile or fiberglass can't hold them. You can fix that by gluing rubber shelf lining material to the ends with strong glue - two-part epoxy or contact cement.
Where should shower rod be placed?
Your curtain rod should be hung a little higher than your shower head, or at the very least, level with the showerhead. This will prevent too much water from splashing out over the top.
Should shower curtain be higher than shower head?
The rule of thumb is to put the shower curtain rod three to five inches higher than the shower curtain's length. At the least, you want the curtain to hang at least six inches past the rim of the tub. What is this? Hanging the rod higher has the effect of making the bathroom ceiling appear taller.
How do you install a Moen curved tension shower rod?
0:484:30Moen Adjustable Curved Shower Rod Installation Video - YouTubeYouTubeStart of suggested clipEnd of suggested clipCheck to see if there's a stud behind the wall where you'll be installing the curved shower rod.MoreCheck to see if there's a stud behind the wall where you'll be installing the curved shower rod. Next simply position the supplied installation templates on the wall in the desired location.
How do you install a zenna curved tension shower rod?
0:271:23Zenna Home NeverRust® Tension Curved Shower Rod from Zenith ...YouTubeStart of suggested clipEnd of suggested clipSet screw to your desired length and finish by twisting the end for a tight secure. Hold your bathMoreSet screw to your desired length and finish by twisting the end for a tight secure. Hold your bath can now have a lifetime of style with a tension curved shower rod that will never rust.
How do you install an L shaped shower rod?
0:122:32How to Install a Corner Shower Curtain Rod - YouTubeYouTubeStart of suggested clipEnd of suggested clipAssemble the rod with the connector. Slide the 1 inch loop onto the curved section of the rod.MoreAssemble the rod with the connector. Slide the 1 inch loop onto the curved section of the rod. Double check to make sure that the rod pieces are the correct length for your installation.
Can you use a curved shower rod in a shower stall?
Curved rods are usually installed closer to the back wall of the shower than a straight rod. The rod must be back far enough so that the curtain is able to be tucked behind the lip of your shower stall.
Why is my tension rod not working?
The caps on tension rods are often made of plastic, but even rubber ones are so incompressible that moist, smooth surfaces such as tile or fiberglass can't hold them. You can fix that by gluing rubber shelf lining material to the ends with strong glue - two-part epoxy or contact cement.
How do you install an L shaped shower rod?
0:122:32How to Install a Corner Shower Curtain Rod - YouTubeYouTubeStart of suggested clipEnd of suggested clipAssemble the rod with the connector. Slide the 1 inch loop onto the curved section of the rod.MoreAssemble the rod with the connector. Slide the 1 inch loop onto the curved section of the rod. Double check to make sure that the rod pieces are the correct length for your installation.
How do you open a shower curtain ring?
0:001:10How to Remove Plastic Shower Curtain Rings - YouTubeYouTubeStart of suggested clipEnd of suggested clipAll you have to do is slide it.MoreAll you have to do is slide it.
The Proper Placement of a Shower Rod | Hunker
Standard shower curtains are 72 inches long by 72 inches wide. If your shower has a tub, it's recommended that the shower curtain and liner, if you're using one, hang below the lip of the tub at least 6 inches.
Where to place shower curtain rod in relation to the tub?
I am not asking how high to mount the shower curtain rod (that is easy to determine from an existing shower curtain). I am trying to figure out how far "into" the tub it should be mounted.
How To Install And Adjust A Shower Curtain Rod | Hunker
Tension rods are the most common type, but they don't always do the job, especially when you use double curtains or heavy ones. In that case, you may need to install a single wood or metal rod supported on the ends by brackets screwed to the walls.
How to measure tension rod for shower curtain?
Your tension rod must be a 3"-4" longer than this so that you can adjust it to fit snuggly. Step 2. Hold up your shower curtain at the appropriate height and use a pencil to mark its ideal location on both walls.
What to use when you rent an apartment and find no shower curtain rod?
If you're renting an apartment and arrive to find there's no shower curtain rod in your bathroom, a tension rod is the best choice.
How far down should a shower curtain hang?
If you have a shower over your bathtub, the shower curtain should hang approximately 5" below the edge of the tub. Step 2. Use the stud finder to determine if there are studs behind the area you marked on the wall. If there is no stud in that location, you'll have to add the additional support yourself. Step 3.
How many rings are in a shower curtain?
Most standard shower curtains come with twelve rings that are available in ring or hook form. If you've chosen rings or hooks with a unique size or style, ensure they will fit the shower curtain and rod you've selected before installation. Step 7. Insert the rod into the holes and attach your curtain to the rings.
What is tension rod?
A tension rod is adjustable and is simply wedged between the two walls using pressure to hold the rod in place. While this is a hassle-free solution in a pinch, it's not as stable as other rods and can fall if you put too much pressure on the shower curtain.
Where to place tension rod?
When deciding where to place a tension rod, consider locating the studs in the wall and positioning either end against a stud. This avoids damaging the drywall if the rod puts too much pressure on an unsupported wall section.
Is a shower curtain rod worth it?
A shower curtain rod might not be one of the design decisions at the forefront of your mind when you're decorating a bathroom, but it's worth your consideration.
How wide should a shower curtain be?
For the best look and fit, select a shower curtain six to 12 inches (15 to 30 cm) wider then the width of the rod.
How high should a shower rod be?
Place the shower rod at least 74 inches (188 cm) above the shower floor. The standard shower curtain is 72 inches (183 cm) long, and when it is linked to shower hooks, it usually gains another two inches (five cm). To prevent the curtain from dragging on the floor of the tub, hang the curved shower rod at a height of 74 inches or more.
What is a shower rod flange?
The flanges are the mounts that hold the curtain rod. Once you’ve centered the shower rod over the edge of your tub and you know the height at which you want to install it, measure down from the ceiling on both sides, and then make a small mark with a pencil or marker on the spot where you’ll need to install the flanges.
How to measure shower enclosure?
Measure the width of your shower enclosure, then subtract it from the length of your shower rod. Divide the difference in half and cut that length from your shower rod. For instance, if your curved shower rod is 50 inches long, and your shower enclosure is 48 inches wide, cut one inch off each end of the shower rod.
What happens if you put a shower rod too low?
If you position the rod too low, you’ll be ducking every time you get in and out of the shower. If you live with other people, install the the curved shower rod at a height that allows the tallest person living in the house to get in and out of the shower without bumping their head. At the opposite end, ensure your rod is not so high ...
Do shower rods stay up?
However, these rods do not stay up as well as shower rods that you mount on the wall. You can use felt pads between the end of the rod and the wall to help them stay put. Consult manufacturer directions for more information. ...
Do curved shower rods need flanges?
Some curved shower rods don’t need flanges installed, and instead feature extendable “feet” that can be pressed directly against the walls of your shower or bathroom. This is called a tension rod and it is held in place by a spring that pushes the ends of the rod outwards.
What is a round shower curtain rod?
Two items in one, this rounded pipe is not only the conduit to the shower head, it also acts as the rod for a privacy curtain. There are also round rods just for the curtains that circle an existing shower head. Put one outside and it's great for washing off after a dirty work day.
How big is a shower curtain?
Standard shower curtains measure 70” x 70” and work for curved rods as well. Round shower curtain rods create more space, up to 33% more, for you as you shower, keeping your skin from touching the curtain. While this makes it feel more spacious, it doesn’t require more curtain to adequately cover the shower area.
Do shower curtains protect the floor?
These shower curtains protect the floor and walls of your bathroom on all sides, allowing you to enjoy a shower in your freestanding tub. If your tub is a soaker tub, primarily intended for bathing, you can still enjoy the privacy that a round shower curtain provides.
Can you use a curved shower curtain with a curved shower rod?
No special type of curtain is required to pair with a curved rod. However, if you prefer additional slack in your shower curtain, go for an extra wide version of a shower curtain. To determine the basic size for your shower curtain, first measure shower rod height from the tub floor to the top of the rod.
Do you need a round curtain rod for a shower?
While this makes it feel more spacious, it doesn’t require more curtain to adequately cover the shower area. No special type of curtain is required to pair with a curved rod.
Can you use a shower curtain rod and a regular curtain rod together?
If you have a round shower curtain rod and a regular shower curtain, you should be aware that you can use them together; however, your regularly-sized shower curtain may not be long enough ( as your round shower curtain rod will, very simply, be longer than a straight one for the same space would be).
Will a round shower curtain work around a bathtub?
A round shower curtain rod works well around a freestanding bathtub. These shower curtains protect the floor and walls of your bathroom on all sides, allowing you to enjoy a shower in your freestanding tub. If your tub is a soaker tub, primarily intended for bathing, you can still enjoy the privacy that a round shower curtain provides.
What to consider when installing shower curtain rods?
When installing the rod, it’s also important to ensure that you use the right kind of material. There are certain elements that you should take into consideration such as the proper design of the curtain as well as its size. Try to make sure that the rod doesn’t obstruct the visibility of the shower from the inside as well as the outside.
Why is it important to install a shower curtain rod?
Learning how to install shower curtain rod in your shower is important if you want to keep the place looking beautiful for a long time. This task will help you save money by keeping the entire area well-maintained. It is important to note that you can easily tackle this task on your own but you should still hire a professional for ...
What do you need to know when installing a material rod?
If you’re planning to install a material rod then you need to make sure that the material is strong enough to handle the weight of the rod. There are different kinds of materials you can choose from but remember that they all have their own benefits and disadvantages.
Do you want to buy rods that are already made?
Do you want to buy the rods that are already made or will you have to buy them from a supplier? This might not seem like a big deal but if you’re just starting out in this business, then you might want to consider buying the rods that are already made because it saves you a lot of time. It also allows you to customize the design according to your tastes and requirements.
Can you install curtain rods labor intensive?
Now that you have done the research to understand the basics of curtain rod installation, you should now consider your design and decide if you want to go for it or not. As I mentioned earlier, this project can be labor intensive but the overall effort will pay off and you’ll be pleased with the end result.
What Is The Standard Size Of A Shower Rod?
Although the standard adjustable sizes range from 57 to 61 inches, you can find some extending up to 73 inches.
Is It Necessary For A Shower Curtain To Touch The Floor?
Generally, you would like your shower curtain to be free of any contact with the floor. The general rule is that your bathtub and shower curtain should overlap by 5 inches. This looks good and ensures water drains back into the tub rather than out onto the floor.
Do Curved Shower Rods Require Additional Space?
Curved shower rods are popular for their aesthetic appeal and the extra space they provide in the shower. It provides a more comfortable shower experience because of this.
How much does it cost to install a shower rod?
If you’re not confident in your ability to install a mounting shower rod, hire a professional to do it for you. It shouldn’t cost more than $150.00 to pay someone to do it for you.
How long does it take to install a tension shower rod?
Tension shower rods come preassembled, which makes installation easy. It shouldn’t take more than 5 minutes to install a tension shower rod. Tip: The standard length of a tub is 60 inches (150 cm), and most tension rods extend from 48–75 inches (120–190 cm).
How to extend a rod on a wall?
Pull the rod out until it reaches the end of the wall on the opposite side. You’ll notice a dividing line in the middle of the rod where one end of the rod slides into the other half. While holding one end against the wall, extend the other half of the rod by pulling it out and sliding it. Extend it until it reaches the wall on the opposite side.
How to tighten a rod?
Hold the larger portion while turning the smaller end of the rod. With your rod in place, brace the larger portion of the rod with your nondominant hand. Then, twist the smaller length of the rod clockwise to tighten it. Continue tightening the rod until it is firmly in place.
What is tension rod?
Tension shower rods are inexpensive, easy to find, and require no tools or hardware. They rely on the tension of your shower’s walls to remain stable and can be easily adjusted or moved. When looking at a tension rod, make sure that the maximum length exceeds the distance between your bathroom’s walls.
Can you slide a shower curtain through a rod?
You can slide the rings for your shower curtain through the rod before installing it if you want to make things easier.
Do shower curtains come with screws?
Mounting shower curtains will come with the screws and brackets needed to install them.
