The steps to use the universal tool are simple:
- Position the pipe side prong so it's fully seated on the pipe. Place the fitting side above the barrel of the SharkBite fitting.
- Squeeze the handle to compress the release collar, which is what makes the fitting let go of the pipe.
- Pull the fitting to remove it from the pipe. Rotate the fitting if necessary to help remove it from the pipe.
How to install shark bite fittings?
How to Install SharkBite Fittings Step 1. Cut the pipe that you are installing in the SharkBite fitting with a pipe cutter. Make sure the end of the pipe... Step 2. Inspect the SharkBite fitting for damage or obstructions. Make sure that the SharkBite fitting, and the pipe... Step 3. Remove the PEX ...
How do you use a Sharkbite on a copper pipe?
Measure one inch up the pipe from the cut end and mark the pipe with a pencil or scribe. Make sure the mark is easily visible as it will help you install the SharkBite fitting correctly. Hold the SharkBite fitting and push the pipe into the fitting with a twisting motion.
What should I do if my Sharkbite fitting is not working?
Make sure that the SharkBite fitting, and the pipe going into it, is clean and undamaged. Replace any SharkBite fittings that appear damaged or that have obstructions. Remove the PEX support collar from the SharkBite fitting if you are using copper or CPVC water lines and local codes prohibit the use of the support collar.
How do I adjust the mark on my Sharkbite?
Make sure the mark is flush, or nearly flush, with the edge of the release ring on the SharkBite fitting. Push the pipe farther into the fitting if the mark is more than .05 inches from the release ring.
What is sharkbite fitting?
What makes Sharkbite fittings superior?
How to make a click sound on a sharkbite?
How long do sharkbite fittings last?
How to cut a pipe with a hacksaw?
How to cut polybutylene pipe?
How big is a push to connect fitting?
See 2 more
How do you install shark bite slip fittings?
0:171:25SharkBite Slip Coupling - Copper or CPVC Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipSimply slide the end of the coupling mark to slip end over the copper as far as it will go using aMoreSimply slide the end of the coupling mark to slip end over the copper as far as it will go using a disconnect clip on the slip end of the fitting.
How do you install a sharkbite slip ball valve?
0:061:03SharkBite Slip Fittings - YouTubeYouTubeStart of suggested clipEnd of suggested clipInstallation is easy just cut out a two inch or less section of the pipe. And slide the slip end onMoreInstallation is easy just cut out a two inch or less section of the pipe. And slide the slip end on first as far as it will go.
What does slip end mean on sharkbite?
A slip fitting does the job of two couplings and extra pipe. Only one end of the coupling has a stop, allowing the opposite end to slide freely over the end of a pipe. The fittings are then released using a disconnect tool and slide back onto the other end of the pipe for a successful connection and leak repair.
What is a slip tee used for?
The “Slip T” PVC fittings, also know as a TL, pass through tees, or slip sling tees are commonly used in building PVC structures where you don't want to compromise the strength of the pipe by cutting it. With no stops in the top of the Slip T, you can simply slide it onto the pipe where you want it.
How does a slip ball valve work?
Slip feature allows for two inches of rigid copper or CPVC pipe to be cut out of an existing line and connected back together by using the disconnect tool to slide the fitting back to the other end of pipe. Innovative push-to-connect design makes for quick and easy installation.
How do you use a copper slip coupling?
0:4710:42How to use slip couplings to tee into a rigid copper pipe - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the way you do it is by using a slip coupling that's a normal cup load that is a solid o-ringMoreSo the way you do it is by using a slip coupling that's a normal cup load that is a solid o-ring fitting coupler. If we take a piece of copper pipe and push that in there it will actually physically.
Do SharkBite fittings leak?
SharkBite fittings are designed to create a leak-proof seal. When a SharkBite fitting does leak, the first thing you'll want to do is see if the pipe is correctly connected to the fitting. By disconnecting and reconnecting the pipe, you may fix the problem.
Do SharkBite fittings fail?
4:097:02SharkBite Fittings - Awesome or A Failure Waiting To Happen?YouTubeStart of suggested clipEnd of suggested clipYou can see almost like like fingernails on a chalkboard dragging off the pipe as it came off. ItMoreYou can see almost like like fingernails on a chalkboard dragging off the pipe as it came off. It did fail but I'll tell you it failed in an impressive way I think this thing's pretty tough.
How long do SharkBite fittings last?
SharkBite fittings last a long time. In fact, SharkBite warrants the fittings for 25 years when used with SharkBite tubing.
What is a slip T fitting?
The "Slip T" PVC Fittings, also know as a TL, pass through tees, or slip sling tees, are commonly used in building PVC structures where you don't want to compromise the strength of the pipe by cutting it. With no stops in the top of the Slip T, you can simply slide it onto the pipe where you want it.
How do you tap into an existing water line?
To tap into existing copper lines, shut off the water. With a tubing cutter cut an opening in each pipe that is about an inch shorter than a tee fitting. Dry-fit the tees. If the pipes are rigidly installed, remove a clamp or two so you can pull the pieces apart slightly.
How far do SharkBite fittings push on?
Pipe Insertion Depth ChartSharkBite Fitting SizeNominal Pipe SizePipe Insertion Depth (in.)1/2 in.1/2 in. CTS0.955/8 in.5/8 in. CTS1.133/4 in.3/4 in. CTS1.101 in.1 in. CTS1.315 more rows
How do you install a SharkBite valve on an existing copper pipe?
4:146:36Replacing Copper Pipes and Fittings with SharkBite Push Fit ConnectorsYouTubeStart of suggested clipEnd of suggested clipSlide it onto the pipe just enough that allow the copper pipe to fit between it and the shutoffMoreSlide it onto the pipe just enough that allow the copper pipe to fit between it and the shutoff valve use the sharkbite tool that comes with the slip end fitting to unlock the sharkbite teeth.
How do you install a SharkBite shut off valve on a CPVC?
0:501:54How to Install a CPVC Supply Stop Valve | SharkBite - YouTubeYouTubeStart of suggested clipEnd of suggested clipAllow the joint to cure according to the solvent's instructions finish by installing your faucet orMoreAllow the joint to cure according to the solvent's instructions finish by installing your faucet or toilet connector from the stop valve to your fixture. Hand tighten the nut until snug.
How far does SharkBite go on pipe?
Pipe Insertion Depth ChartSharkBite Fitting SizeNominal Pipe SizePipe Insertion Depth (in.)1/2 in.1/2 in. CTS0.955/8 in.5/8 in. CTS1.133/4 in.3/4 in. CTS1.101 in.1 in. CTS1.315 more rows
How do you change a SharkBite shut off valve?
1:022:01How to install and remove a Sharkbite shut off valve - YouTubeYouTubeStart of suggested clipEnd of suggested clipOff there's a little removal tool that you're going to use you slide over the pipe like that andMoreOff there's a little removal tool that you're going to use you slide over the pipe like that and then you're going to actually grip the back of the removal tool in the front of the valve.
6 TRICKS To Remove A Sharkbite Fitting (New Tricks!) | GOT2LEARN
Here are 6 ways to remove a Sharkbite or push fitting using different tools than a dedicated removal tool, in case you lost it. -----...
Video: How to Install Push-to-Connect Fittings | SharkBite
In this how-to video, our experts walk you through each step of installing a SharkBite push-to-connect fitting. No special tools needed! Watch now.
1. Identify the pipe material
To get started, identify the pipe material. SharkBite brass push-to-connect fittings are compatible with PEX, Copper, CPVC, PE-RT and HDPE pipe. SharkBite fittings come with a PEX stiffener pre-loaded into the fitting for PEX, PE-RT and HDPE. The PEX stiffener does not need to be removed for Copper or CPVC applications.
2. Cut pipe cleanly & squarely
Be sure the pipe is free of scratches or debris and cut the pipe as cleanly and squarely as possible. If you are working with copper pipe, use a deburr tool or sand paper to remove any sharp edges or burrs on the pipe. Failing to deburr the pipe properly can compromise the fitting.
3. Measure & mark the insertion depth
Use your SharkBite Deburr & Gauge Tool to measure and mark the insertion depth on your pipe.
4. Make the connection
Push the fitting to the insertion mark you just made on the pipe. Now, turn on the water and check the connection.
What is sharkbite fitting?
First, SharkBite fittings are the push-to-connect type of water pipe fittings. Before the introduction of the push-to-connect fittings in the US, this type of plumbing system was not popular as they are today. However, since Reliance Worldwide Corporation (RWC) introduced them in the US market nearly 20 years ago, some brands have become more successful than others. Some customers even refer to other brands as SharkBite.
What makes Sharkbite fittings superior?
What makes SharkBite fittings superior comes down to its design and components. The unique connection system allows the reuse of the fittings and saves time by reducing the installation time. So, what makes it so secure? A push to connect fitting is only as good as its body material and parts. Here are some of its internal elements to help you understand how SharkBite works.
How to make a click sound on a sharkbite?
This is the easy part. Hold the SharkBite fitting and gently push the pipe through it with a slight twist. Once it touches the pipe stop , you will hear a click sound from the fitting.
How long do sharkbite fittings last?
With regular use, SharkBite fittings can last up to 25 years. Besides, it is an easy process to replace the parts when the time comes.
How to cut a pipe with a hacksaw?
First, inspect the pipe for any deformations and remove all adhesive labels that may cause leakage issues later. Proceed to use a pipe cutter to cut the line and then deburr to remove any sharp edges and burrs. It is advisable to never use a hacksaw during the cutting process. Deburring prevents damage to the O-ring when pushing in the pipe. For polybutylene or PEX, use pipe cutters to cut the line, then insert the manufacturer’s tube liner. Again, check for any cracks and remove any obstructions from the end of the pipe.
How to cut polybutylene pipe?
Next, use a disconnecting clip or tape measure and mark one inch up from the cut end.
How big is a push to connect fitting?
These push-to-connect fittings come in different sizes ranging from ¼ inch to 2 inches in diameter. This makes them ideal for both commercial and personal projects.
Is sharkbite a personal choice?
Sharkbite is a personal choice and I like the idea where it is now located. If it would have been in another location I might have a different opinion
Do you use a ball valve on a hose bib?
I use ball valves to isolate my hose bibs. I gave up on the frost free valves years ago. The most important thing is to remember to open the hose bib after you isolate it with the ball valve.
Does Sharkbite stop water from going to the outside hose bib?
Yes the picture is correct, the water flow is as indicated but the Sharkbite valve I just installed downstream will stop any water from going to the outside hose bib.
How to make a sharkbite pipe?
Hold the SharkBite fitting and push the pipe into the fitting with a twisting motion. Push the pipe into the fitting until you hear a "click" sound coming from the fitting. Look for the pencil mark that you made on the pipe. Make sure the mark is flush, or nearly flush, with the edge of the release ring on the SharkBite fitting. Push the pipe farther into the fitting if the mark is more than .05 inches from the release ring.
How to remove a leaking Sharkbite pipe?
Slide the SharkBite release tool up the pipe to the release ring on the leaking fitting. Push the tool toward the SharkBite fitting to depress the release ring. Pull the pipe out of the fitting with a twisting motion. Inspect and clean the end of the pipe and the fitting. Install the pipe again, making sure to fully seat the pipe into the SharkBite fitting.
How to remove sharkbite support collar?
Remove the PEX support collar from the SharkBite fitting if you are using copper or CPVC water lines and local codes prohibit the use of the support collar. Depress the SharkBite release ring with the release tool and pull the collar out of the fi tting with needle-nose pliers.
What is sharkbite fitting?
SharkBite fittings eliminate the need for solvents, crimpers and torches.
Why keep sharkbite fittings in tool box?
Consider keeping SharkBite fittings in your tool box for emergency repairs. A SharkBite fitting will be quicker and easier to install if you ever have a water line break in the middle of the night.
Do you need to check your plumbing codes before installing sharkbite?
Check your local plumbing codes before you install SharkBite fittings in your home. Wear eye protection when cutting and deburring pipes.
What is sharkbite fitting?
First, SharkBite fittings are the push-to-connect type of water pipe fittings. Before the introduction of the push-to-connect fittings in the US, this type of plumbing system was not popular as they are today. However, since Reliance Worldwide Corporation (RWC) introduced them in the US market nearly 20 years ago, some brands have become more successful than others. Some customers even refer to other brands as SharkBite.
What makes Sharkbite fittings superior?
What makes SharkBite fittings superior comes down to its design and components. The unique connection system allows the reuse of the fittings and saves time by reducing the installation time. So, what makes it so secure? A push to connect fitting is only as good as its body material and parts. Here are some of its internal elements to help you understand how SharkBite works.
How to make a click sound on a sharkbite?
This is the easy part. Hold the SharkBite fitting and gently push the pipe through it with a slight twist. Once it touches the pipe stop , you will hear a click sound from the fitting.
How long do sharkbite fittings last?
With regular use, SharkBite fittings can last up to 25 years. Besides, it is an easy process to replace the parts when the time comes.
How to cut a pipe with a hacksaw?
First, inspect the pipe for any deformations and remove all adhesive labels that may cause leakage issues later. Proceed to use a pipe cutter to cut the line and then deburr to remove any sharp edges and burrs. It is advisable to never use a hacksaw during the cutting process. Deburring prevents damage to the O-ring when pushing in the pipe. For polybutylene or PEX, use pipe cutters to cut the line, then insert the manufacturer’s tube liner. Again, check for any cracks and remove any obstructions from the end of the pipe.
How to cut polybutylene pipe?
Next, use a disconnecting clip or tape measure and mark one inch up from the cut end.
How big is a push to connect fitting?
These push-to-connect fittings come in different sizes ranging from ¼ inch to 2 inches in diameter. This makes them ideal for both commercial and personal projects.
