How to install a low profile shower tray
- Check the floor beneath. Before you start, you need to make sure that the floor beneath the tray is capable of supporting it.
- Cut access hatch. You’ll need to cut out an access hatch in the floorboards next to the tray as this will allow you to reach the waste.
- Cut waste hole. ...
- Lay mortar. ...
- Connect to outlet pipe and seal. ...
Full Answer
How do I install a shower tray waste?
Firstly, place the tray loosely where you want to eventually install it to check for any fitment or clearance issues. Screw the legs into position and adjust the height to the level you require at this point. Briefly fit the shower tray waste and check everything lines up correctly.
How do I install the tray?
Firstly, place the tray loosely where you want to eventually install it to check for any fitment or clearance issues. Screw the legs into position and adjust the height to the level you require at this point.
How do height adjustable shower trays work?
Basically, height adjustable shower trays use legs which are situated underneath the tray itself, raising the profile of it. These are really popular as they allow you much easier access to the pipes if anything needs replacing in the future. We’ll cover both options for this guide.
What is the best tool to cut shower tray waste?
A jigsaw is the ideal tool for this as it’ll allow you to be more precise with your cutting. A hole will also need to be cut for your shower tray waste so take some accurate measurements and very carefully start creating the space you need. Once this is done you can go ahead and assemble the waste itself.
Do you have to put cement under a shower tray?
Designed to drain water from the shower, it protects your floor from water intrusion, rot and mold. Installing one requires some skill and there are certain rules and procedures to follow when doing so. In some cases a mortar bed is a necessity; other times it isn't.
What do you put under shower base?
The best type of mortar to use underneath a shower base is a mixture of Portland cement and sand. This mortar will both support the weight of the shower and provide a barrier that helps prevent water damage to the floor underneath.
How should a shower tray be fitted?
Step 1 - Position the shower tray where you want it installed and make sure it fits into the space with no clearance issues. Screw the legs into position and adjust the height until the tray is at the desired level. Attach the tray's waste outlet to make sure that everything lines up properly.
What do you stick a shower tray down with?
Using either tile adhesive, silicone or a weak cement mix (5 parts sand/ 1 part cement) apply sufficient to board to cover entire underside of tray.
How do you secure a shower base to the floor?
1:463:22How to Install a Shower Pan | The Home Depot with @This Old HouseYouTubeStart of suggested clipEnd of suggested clipWe added temporary strapping to the studs to hold the pan in place some manufacturers call for theMoreWe added temporary strapping to the studs to hold the pan in place some manufacturers call for the flange of the shower pan to be screwed directly to the studs.
What is the difference between a shower pan and a shower base?
What Do They Do? While a shower pan and a shower base both channel water into the drain, there's one key difference: “Shower pan” is the actual shower floor that you step on, whereas “shower base” refers to the structure underneath the shower itself.
Can you put a shower tray on floorboards?
When learning how to lay a shower tray on a wooden floor, you will need to mark the area where the tray will stand. Next, replace the floorboards within that area with a minimum of 18mm marine ply. You will need to ensure there is access to the waste pipes in the floor beside the tray.
How do you fix a shower tray to the wall?
1:212:33Installing a shower tray - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe recommend using cement to level the floor and fix it in place. Make sure to place the rubber sealMoreWe recommend using cement to level the floor and fix it in place. Make sure to place the rubber seal before installing the shower tray. Place the shower tray on the floor.
How do you seal a shower tray before tiling?
2:544:49Sealing a shower tray with HydroHALT TileBud ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse the backer rod wheel with a sealant nozzle to roll the backer rod down into the joint. ApplyMoreUse the backer rod wheel with a sealant nozzle to roll the backer rod down into the joint. Apply sealant into the joint formed between the strip and the shower tray sidewall rub up the joint sealant.
Do you have to waterproof under a shower base?
In bathrooms, all timber floors including particleboard and plywood are to be fully waterproofed over their entire surface area, excluding the area under a preformed shower base or built-in bath, whether the shower is enclosed or not.
Can you fit a shower tray after tiling?
Can you put a shower enclosure over tile? It is possible to install wall panels over tiles that are already in place if you want to replace your shower and the glass panel.
What sand do you use to bed a shower tray?
It is recommended that you use a suitable silicone sealant around the waste to create a watertight seal. DO NOT PROCEED IF NOT SATISFIED. Mix 1 part ordinary cement to 5 parts soft sand. Mix the two together on a smooth hard surface.
Do you need to waterproof under shower base?
In bathrooms, all timber floors including particleboard and plywood are to be fully waterproofed over their entire surface area, excluding the area under a preformed shower base or built-in bath, whether the shower is enclosed or not.
Can I use spray foam under a shower base?
Only a minimal-expanding foam should be used under a shower pan. The reason for this is that when foam expands it exerts pressure against opposing forces. And so, you could end up with bowing or even cracking of your shower pan.
What is the best base for a shower?
4 of the Best Shower Base Flooring OptionsTile Shower Bases. You may decide that you want to tile the floor of your shower to match the walls or bathroom floor tile. ... Molded Stone Shower Bases. Molded stone shower pans can offer you another high-end and elegant solution. ... Acrylic Shower Pans. ... Fiberglass Shower Pans.
How do you install a shower base on a concrete floor?
Remove enough concrete to allow space for the waste pipe.Place pipe and drainage tool into the hole.Test the pan to make sure it fits properly.Apply mortar to the concrete base.Place the shower tray over the mortar, pressing firmly.Screw the drain into place.Let the mortar dry for 24 hours.More items...•
What to consider when installing a new shower?
However, it’s not often we consider the tray that rests beneath our feet, catching all the excess water and faithfully carrying it away.
How to install a raised tray?
If you are installing a raised tray, insert the feet into the correct positions, using your screwdriver and the fittings provided. With the help of your spirit level, make sure they are even and adjusted to the height specified in your manual. Attach the clips onto the edge where the front panel will be fitted.
Can you install a shower tray over the floor?
If the waste trap (the fitting that connects the plughole of the shower to the waste pipe) is flush with the floor, you can install the tray directly over the top. If the waste pipe is fitted above the floor, the tray will need to be raised and installed over the top.
Do you need a waste pipe for a shower?
Depending on the size and style of the waste pipe, the type of shower tray you need to fit in your bathroom will vary.
Do you need an access hatch for a shower tray?
It is important to review the steps for attaching the waste beforehand, as if your shower tray is fitted to the floor you may need to create an access hatch so you can attach the appropriate fittings after the tray has been placed.
What type of tray are you shower installing?
Before we go any further, you need to know whether you’ll be fitting a height adjustable tray or a low profile one as their installation methods will differ slightly. Basically, height adjustable shower trays use legs which are situated underneath the tray itself, raising the profile of it. These are really popular as they allow you much easier access to the pipes if anything needs replacing in the future. We’ll cover both options for this guide.
Can you cut a hole in a shower tray?
A hole will also need to be cut for your shower tray waste so take some accurate measurements and very carefully start creating the space you need. Once this is done you can go ahead and assemble the waste itself.
What is a tutorial channel?
A channel showing tutorial videos about all aspects of building and home improvement works including plumbing, electrical, painting and decorating, plastering, joinery, carpentry, tiling. Videos presenting professional and experienced jobs
Can you add videos to your watch history?
Videos you watch may be added to the TV's watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.