Connect the red-colored positive battery cable and tighten the clamp. Connect the black-colored negative battery cable and tighten that clamp. Apply the battery grease to the cable connectors also. Verify all the connections are secure. Once done, you have done with the project of replacing your side post battery.
Full Answer
How do I replace the battery on my Side post battery?
In order to replace the battery, place the side post battery securely into the battery box and reinstall the hold down assembly. Apply the battery grease to the side post terminals to prevent corrosion build-up. Connect the red-colored positive battery cable and tighten the clamp.
How do you hook up two batteries in a parallel circuit?
To hook up the parallel circuit, route the “hot” starter lead to one battery, then run a line from the (+) post on one battery to the (+) post on the second battery. The second battery should then have its negative post (-) grounded with a cable joining both (-) terminals on the battery.
Where do you mount a battery?
Some chassis builders prefer to mount the batteries in a position that's parallel to the sides of the vehicle (which is the same as many Detroit installations). If you're mounting a battery or two in the trunk, you'll need a rear battery switch.
What is a side post battery?
A side post battery has the positive and negative terminals located on the side of the battery rather than on the top of the battery. Generally, car batteries need to be replaced every three to five years.
How do you hook up a side terminal battery?
3:587:07How to add wires to side post Chevy batteries when you need ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou'll just take your terminals. Say there's a wire on this terminal. And you're to slide them rightMoreYou'll just take your terminals. Say there's a wire on this terminal. And you're to slide them right over here.
How do you remove a battery from side post?
0:334:08How to replace battery side post terminal bolts on GM VehiclesYouTubeStart of suggested clipEnd of suggested clipSo i'll just tilt it to one side. And it kind of pops out there in place comes out of the uh ringMoreSo i'll just tilt it to one side. And it kind of pops out there in place comes out of the uh ring there.
Which side battery do you connect first?
Positive“Positive first, then negative. When disconnecting the cables from the old battery, disconnect the negative first, then the positive. Connect the new battery in the reverse order, positive then negative.”
Can you install a car battery on its side?
Our batteries can be operated in virtually any orientation without loss of capacity or electrolyte leakage. However, upside down operation is not recommended.
How do you change a side post battery to a top post battery?
Upgrading Your Car Battery: Converting a Side-Post to a Top-Post StyleFind a Safe Location. ... Gather Your Tools. ... Start With Cable Removal. ... Alter the Cable Ends. ... Replace the Battery's Terminals. ... Reattach the Positive Side. ... Connect the Negative Side. ... Apply a Corrosion-Resistant Spra.
What size bolt fits a side terminal battery?
What Is The Standard Battery Terminal Nut And Bolt Size? The standard battery terminal nut and bolt size is 1/4-20. This is the same size as the battery terminal studs on most cars and trucks. The 1/4-20 size is also the same as the thread size on most household light bulbs.
How do you know which way batteries go in?
Look for a plus symbol on your battery. The plus sign, or +, indicates the positive terminal. On AA, AAA, C, and D batteries, the positive end should be slightly raised. The negative end of the battery should be flat, and it may or may not be marked with a minus, or -, symbol.
Do you hook up red or black first?
Attach the red jumper cables first. Start by clamping one red cable to the positive side of the battery that won't start. Then attach the other red clamp to the positive side of the working battery. Next, clamp one black cable to the negative side of the working battery.
What happens if you connect negative first?
This is because the negative terminal is connected to the chassis of the car, which is grounded. If you were to connect the negative terminal first, you would create a circuit between the negative terminal and the chassis. This could cause sparks and potentially damage your battery or electrical system.
Can I mount a sealed battery on its side?
The sealed battery has a one-way valve designed to release any excess pressure if the battery is overcharged. Unlike flooded batteries, a sealed battery will not spill acid when tipped on its side, allowing it to be mounted in different positions.
Can gel batteries be installed on their side?
The AGM and Gel batteries can be mounted on their sides with no problems, but should not be mounted upside down.
Can AGM battery be laid on its side?
Battery Orientation Print Rolls VRLA AGM batteries should be installed upright for best performance and may not be mounted upside down or horizontally on the end (shortest side) of the case.
How do I remove a stripped battery terminal bolt?
Answer provided byUse pliers to wiggle the nut back and forth and loosen it. It should help it come off easier.Cut off the nut with a hacksaw. ... Buy a bolt removal tool like go2 socket that lets you adjust the size and grip of your socket.Use a bolt or screw extractor to pull it out.
How do you remove terminals?
1:183:11Removing Car Battery Terminals - YouTubeYouTubeStart of suggested clipEnd of suggested clipA ten millimeter wrench to remove the terminals and pliers to gently nudge them. Off. AlwaysMoreA ten millimeter wrench to remove the terminals and pliers to gently nudge them. Off. Always remember that the negative cable is the first cable to be removed.
How do you fix a broken battery post?
0:064:24How to Repair a Battery Post Solved - YouTubeYouTubeStart of suggested clipEnd of suggested clipBit. You want the threads to stick out past the end so just kind of eyeball it and you'll see thatMoreBit. You want the threads to stick out past the end so just kind of eyeball it and you'll see that the threads.
Where to mount AGM batteries?
Some chassis builders prefer to mount the batteries in a position that's parallel to the sides of the vehicle (which is the same as many Detroit installations).
What is Jerry Bickel's battery mount?
Jerry Bickel builds this lightweight, sturdy single battery mount setup. It’s built from chromoly, and it’s designed to solidly mount the battery in the trunk of your car. Bickel also builds these in dual battery configurations. FYI, some sanctioning body regulations mandate a 3/8-inch fastener size, which this system incorporates.
What is AGM battery?
The AGM (absorbed glass mat) design of the battery makes it difficult, if not impossible, for the plates to wander. Keep in mind, though, other batteries might mandate a specific mounting orientation.
Why do you put batteries between the frame rails?
This is one of the primary reasons most chassis builders solidly mount the batteries between the frame rails. You don’t want batteries flying out of the mounts. You can save weight in other areas, but battery mounts are no place to look for easy weight reduction (but you can opt for robust mounts that aren’t portly either — see below).
What happens if you mount batteries too high?
If you mount the batteries too high, then the posts or other electrical connections can touch the deck lid. Pro deck lids are constructed from carbon fiber, and it’s a good electrical conductor. This limits the mounting location for the batteries.”.
How much does a battery weigh in NHRA?
For some NHRA racers, batteries can weigh between 100-150 pounds per pair, including battery boxes. The maximum weight depends on the class requirement as different classes have different regulations. The bottom line is your battery (or batteries) can be used to your advantage as ballast. Given the importance of weight, ...
Why do you need a rear battery switch?
The primary reason for an easily accessible master cut-off switch is to allow someone to turn all electrical power off in the event of an accident.