Put up one piece of the medallion, using the guide you put on the ceiling with the electrical box centered. Secure it with the screws just below the surface. Apply adhesive to the other side of the medallion (you should have already started three screws) and carefully slide it into place until it matches the piece already installed.
How to install a two piece ceiling medallion?
- Turn off power to the light fixture at the fuse/breaker box.
- Clean the area on the ceiling where the medallion will rest using soap, water and an abrasive sponge.
- Center the light fixture's cover plate on the face of the medallion.
- Drill a hole inside the circle with the portable drill fitted with the 3/8-inch bit.
How to paint and install a ceiling medallion?
- caulk
- finishing nailer (with compressor)
- filler
- sanding block
- paint
- light fixture (linking ours for this project)
- ceiling medallion (linking ours for this project)
- longer screws (you’ll want these to match the thread of whatever screws came with your light fixture… just longer!)
How to hang a ceiling medallion?
What You Need
- Polyurethane ceiling medallion
- Wire nuts
- Drill and large bit
- Drywall saw
- Sandpaper
- Long threaded bolt (optional)
- Paint for touch-up and finish
- Adhesive caulk
- Trim-head screws
How to construct a ceiling medallion with plaster?
Option 1: Cutting The Medallion Pattern Manually
- Print out the image (from above) 4 times. If you are trying to make a larger version of the medallion than your printer can handle, try taking it to ...
- Lay down your mat board with the rough side facing up. Make sure it is on something that you can cut on.
- Spray the mat board with adhesive. ...
How are ceiling medallions attached?
0:451:45How to Install a Ceiling Medallion - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst we'll drill a pilot hole. Then apply the construction adhesive to the back of the medallion.MoreFirst we'll drill a pilot hole. Then apply the construction adhesive to the back of the medallion. Set the medallion in place. Then drive in a few screws. To hold it until the glue dries.
How do you cut a hole in a ceiling medallion?
Using a large bit, drill a hole in the center of the medallion to provide access for the drywall saw. Insert the drywall saw into the drilled hole and cut along the small circle you just drew. Sand the hole edges smooth.
How do you attach a plastic medallion to the ceiling?
1:573:12Easy Medallion Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe plastic anchor locator is specially designed to use as a drive depth gauge inserting each screwMoreThe plastic anchor locator is specially designed to use as a drive depth gauge inserting each screw until the screw head meets the lip of the anchor assures perfect placement.
What glue do you use for ceiling medallions?
For the adhesive, Milkie recommends Loctite Power Grab, a type of polyurethane construction adhesive that gets tacky almost instantly. "If you hold the medallion to it for five seconds, it will stay up there," he said.
What is the inside diameter of a ceiling medallion?
Ceiling medallions are available in a wide range of sizes, from 4 inches in diameter for a closet or dressing room to over 36 inches for large rooms.
How do you measure ceiling medallion opening?
First, measure the length and the width of the room and multiply those numbers. That will give the square footage. Once you have that number, divide it by seven; that number is the diameter of the ceiling medallion that you need.
Are ceiling medallions out of style?
While always a classic, the ceiling medallion is once again fashionable in modern-day home design.” Gigi Lombrano, Gigi Lombrano Interiors. “Ceiling medallions are classic!
Do electricians install ceiling medallions?
Most electricians are very familiar with installing medallions with the light fixture. The medallion should have a pre-cut hole directly in the middle to allow electrical wiring to run through it. Bellow are step-by-step directions on how to properly install a ceiling medallion in your home.
How can I hide the gaps around my ceiling light box?
0:072:29How to Hide Gaps Around a Ceiling Light Box - YouTubeYouTubeStart of suggested clipEnd of suggested clipGo ahead and put it up then I'm just going to bend the wires out to hold it up there. Why I getMoreGo ahead and put it up then I'm just going to bend the wires out to hold it up there. Why I get ready it's amount of light. So we'll take the light.
How do you cut a polyurethane medallion?
The polyurethane material is easily cut so you can use a hole saw or a drill to punch out a hole. The hole doesn't have to be perfect since the fixture canopy will cover the hole. Dry fit your medallion in place on the ceiling to make sure all of the wiring and fixture parts will fit as planned.
Do you paint ceiling medallions?
Ceiling medallions can be painted to match the ceiling color, trim color, a favorite piece of furniture, or the overall theme of a room. Because they are sometimes thought of as old-fashioned or regal, a finish can also give them an antique look.
Can you use a ceiling medallion with a ceiling fan?
Related Articles. Ceiling medallions come in a variety of sizes and finishes and can even be painted to match the existing decor of a room. These ornate circular pieces of molding fit around the top of light fixtures or ceiling fans where they meet the ceiling.
Step 1: Remove and Clean
Shut off the power to the light that you're removing and take down the fixture. Cover all wire ends with wire nuts. Thoroughly level and clean the ceiling where you will hang the medallion.
Step 2: Measure Medallion Hole
If your ceiling medallion doesn't have a hole, you'll need to create one for the light fixture. That hole will allow you to pull the light fixture's electrical wiring through, but it should be small enough to hide the wiring. Measure the light fixture's cover plate, and transfer that measurement to your medallion.
Step 3: Cut Medallion Hole
Using a large bit, drill a hole in the center of the medallion to provide access for the drywall saw. Insert the drywall saw into the drilled hole and cut along the small circle you just drew. Sand the hole edges smooth. Then check that the light fixture's threaded bolt is long enough to reach past the ceiling medallion.
Step 4: Prep Medallion
Paint or finish the medallion as desired. Apply adhesive caulk to the back of the ceiling medallion; center and attach to the ceiling.
Step 5: Glue Medallion
Using trim-head screws, attach the medallion to the ceiling while the adhesive dries. Caulk over the screw heads.
Click to Shop & Buy the Best Architectural Ceiling Medallions from World of Decor
Ceiling medallions from World of Décor provide sought after architectural detail, add interest to a chandelier, and dimension to an otherwise vast, open ceiling.
Surface and Ceiling Medallion Preparation
Where to Mount the Ceiling Medallion - locate the mounting space s placed evenly around the border (shallow indented areas without the decorative cabochon caps) - [A]. Use a 1/4” drill bit to drill though the medallion to create mounting holes in these allotted locations.
Installation of Ceiling Medallion on Dry-Wall Ceilin
Position your ladder (s) carefully to allow you to hold the medallion safely in place with the assistance of a partner.
Ceiling Medallion Warranty from World of Decor
World of Decor warrants all its products to be free from manufacturing defects for a period of three [3] years from date of purchase. This warranty does not include damage or other problems resulting from improper installation, misuse or normal wear and tear. World of Decor's liability is limited to product replacement cost.
