- Locate a flat, level area to setup the pool. Make sure the ground is free from sharp objects that may puncture the pool.
- Carefully unfold the pool and inspect seams for manufacturing defects. Lay the pool flat on the ground. ...
- Locate the pool so that the pump is 10 to 21 feet away from the electrical outlet.
Are summer waves pumps any good?
Polygroup’s brand Summer Waves has produced high-quality and efficient pool pumps that circulate the water in the pool. The company emphasizes the importance of sports and health and creates a variety of products that are essential for both health and pleasure. Pool pumps are great and vital for the health of the pool.
How do you set up a pool with a filter pump?
SETUP INSTRUCTIONS 1.Set up the pool by following all the instructions that came with the pool. Do not fill with water until the Filter Pump is properly installed. Locate the Skimmer and Inlet openings on the pool wall. 3.Remove the Seal Ring by turning it counterclockwise.
Is it time to replace your pool pump?
Some unwanted issues may always happen with your pool pump, this is usual. At that moment a pump needs to be replaced or it needs some extra troubleshooting. Summer waves swimming pools and pumps are some of the most well known pool pumps that you can use for having a joyful summer inside your swimming pool.
How do I set up my pool for the first time?
1.Set up the pool by following all the instructions that came with the pool. Do not fill with water until the Filter Pump is properly installed. Locate the Skimmer and Inlet openings on the pool wall. 3.Remove the Seal Ring by turning it counterclockwise.
How do you hook up a pump to a summer wave pool?
1:593:10Summer Waves® RX Filter Setup - YouTubeYouTubeStart of suggested clipEnd of suggested clipPlace one hose clamp onto the hoses. Slide the hose onto the suction fitting and to the pump. InletsMorePlace one hose clamp onto the hoses. Slide the hose onto the suction fitting and to the pump. Inlets then tighten the hose clamp until secure.
How do I hook up my Intex sand pump to Summer Waves pool?
0:395:40Intex Krystal Clear Sand Filter Pump hooked up to a Summer Waves ...YouTubeStart of suggested clipEnd of suggested clipThe the most difficult part honestly of this whole operation hooking it up to the the filter wasMoreThe the most difficult part honestly of this whole operation hooking it up to the the filter was getting an adapter that goes from a one and a half inch to one and a quarter inch.
How do you install a pool water pump?
0:043:19How to Set Up a Swimming Pool & Filter Pump - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake the inner seam. And tuck it under the rim. So that it flattens the bottom of the pool. FillMoreTake the inner seam. And tuck it under the rim. So that it flattens the bottom of the pool. Fill your pool up with water. And smooth out the bottom as it fills.
How do you install an above ground pool pump?
1:068:17Start Up Instructions for your New Above Ground Pool - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe first thing we're going to do is this is your skimmer. You have a basket inside that skimmer onMoreThe first thing we're going to do is this is your skimmer. You have a basket inside that skimmer on a week-to-week basis you're going to go in there you're going to pull your basket.
Can you use a sand pump on a Summer Waves pool?
Your SFX Summer Waves pool can now operate with a sand filter pump by Polygroup! This adapter will also allow you to use a traditional RX ground pump with your pool.
How do I connect my summer waves sand filter?
0:396:06Sand Filter Instructional - YouTubeYouTubeStart of suggested clipEnd of suggested clipPart start by applying the gasket to the fitting. Then insert the pool fittings with the gasket intoMorePart start by applying the gasket to the fitting. Then insert the pool fittings with the gasket into the liner wall. On the outside of the liner apply the thrust washer to the fitting followed.
Can I install a pool pump myself?
A professional electrician will be needed to disconnect the wiring before a pump can be removed. Once a new pump is installed, an electrician will again be necessary to reconnect the wires to the new pump. A do-it-yourself homeowner with basic mechanical aptitude can replace the pool pump in a relatively short time.
Should pool pump be bolted down?
Pool pumps are meant to be bolted down to the concrete pad. This protects the pump from movement and theft (yes, some areas have problems with pool equipment theft), but stops vibration noise or chattering on the concrete.
How long does it take to install a pool pump?
Filling your pool with water (two to three days) Installing the pool pump (one to three hours) Installing the pool filter (less than 48 hours) Installing the pool heater (one to seven days, depending on the heater type)
How far should pump be from above ground pool?
Stay close to the pool Shorter pipe runs = less work for the pump which extends the life of the pump and uses less electricity. Our projects typically average a distance of 20–40 feet from the pool to the equipment, but as stated earlier, much longer runs are sometimes required.
How long do I run my summer waves pool pump?
On average, you should run your pool pump around 6-8 hours per day during winter and 10-12 hours per day during summer. Note that you need to run your pool pump longer during summer because algae grow more in warm temperatures.
Where does the pump go above ground pool?
1:143:12Where Should I Locate My Pool Filter System? - YouTubeYouTubeStart of suggested clipEnd of suggested clipNo more than two to three feet below the height of the pump. Having the pool level with the pump.MoreNo more than two to three feet below the height of the pump. Having the pool level with the pump. Makes.
How do you convert Summer Waves pool pump to sand filter?
2:074:09CONVERT SUMMER WAVES FILTER TO INTEX SAND FILTER - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo with the motor what I did was I took it apart I unscrewed the top and I took out the impeller.MoreSo with the motor what I did was I took it apart I unscrewed the top and I took out the impeller. Once I took out the impeller and the cover for the impeller I just left it like that.
Can you use Intex filter in Summer Waves?
Product Description. This two Pack of filters will work with Intex, summer escapes & summer waves pool pumps that use an a or C filter.
Are Intex and summer waves the same?
Is Summer Waves and Intex the same? No, they are both different brands and each is owned by a different company. Both pool brands offer easy to set up inflatable above ground pools. Intex calls it their Easy Set pools set while Summer Waves market their inflatable pools as Quick Set Pools.
How do you hook up a sand filter to an Intex pool?
3:265:10EASY UPGRADE- SAND FILTER - SALTWATER SYSTEM - YouTubeYouTubeStart of suggested clipEnd of suggested clipThey connect right into the valve here and you could turn the water on and off with these valves.MoreThey connect right into the valve here and you could turn the water on and off with these valves.
Where is the water level on a skimmer?
The water level should be between the min and max markers located inside the skimmer canister ring.
How to prevent drowning in pool?
Drowning occurs silently and quickly and can occur in as little as 2 in. (5 cm) of water. 2.Keep children in your direct sight, stay close, and actively supervise them when they are in or near this pool and when you are filling and emptying this pool. 3.When searching for a missing child, check the pool first, even if the child is thought to be in the house. 4.Locate pumps and filters in such a way that children cannot climb on them and gain access to the pool. 5.WARNING: To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times.
What is the installation procedure for a circulation system?
1.Installers shall follow written instructions regarding positioning of all equipment connected to the circulation systems. 2.The installer shall follow written instruction provided for operation of the circulation system components. 3.All circulation system components and pumps that require replacement or servicing shall be installed according to the pump’s instruction manual. 4.Circulation equipment shall be installed per manufacturer’s instructions to provide proper mounting and support, to prevent damage from misalignment, settlement, and vibration, and to minimize the potential for the accumulation of debris and moisture. Please refer to pump’s instruction manual.
Why are all components of a pool positioned?
All of these components shall be positioned so as to prevent their being used as a means of access to the pool by young children. (See Barrier Code for Residential Swimming Pools, Spas, and Hot Tubs.)
How to keep unsupervised children from accessing pool?
Keep unsupervised children from accessing the pool by installing fencing or other approved barrier around all sides of pool. State or local laws or codes may requirefencing or other approved barriers. Check state or local laws and codes before setting up pool.
How to prevent children from climbing in pool?
1.Keep unsupervised children from accessing the pool by installing fencing or other approved barrier around all sides of pool. State or local laws or codes may require fencing or other approved barriers. Check state or local laws and codes before setting up pool. 2. Toys, chairs, tables or similar objects that a young child could climb shall be at least four feet (4’) [121.92 cm] from the pool. The pump filter system shall be positioned so as to prevent it being used as a means of access to the pool by young children. Do not leave toys inside pool when finished using, since toys and similar items might attract a child to the pool. 3.Position furniture (for example, tables, chairs) away from pool and so that children cannot climb on it to gain access to the pool.
Can you sit on a pool wall?
DO NOT SIT ON OR LAY OVER POOL WALL
