How to Install Traverse Curtain Rods
- Step 1. Measure the window to determine bracket placement. Brackets should be installed approximately 2 inches outside...
- Step 2. Attach the brackets to their predetermined position by installing the hardware that was included in the bracket...
- Step 3. Install the curtain rod by pushing it into the brackets until it clicks. After the...
How do you replace a traverse curtain rod?
Remove the traverse curtain rod from the mounting bracket. Place the rod on a flat surface. If working with a large rod, it may be necessary to lay the rod on the floor, where it can lay flat. Flip the rod over to expose the back of the rod, the carriers and the end brackets. Slide the carriers to one end of the rod.
How do you use a traverse rod hardware?
Some traverse rod hardware operates via a side draw, while others use a center draw. The plastic ring hangers fit into a slot opening at the back of the rod. An S-shaped pin attaches to the pleats in your drapes with its hook end through the small hole in the hanger.
Can you replace the hangers on traverse rods?
The hangers are inexpensive to purchase and easy to install. In just a few minutes' time, you can replace the hangers and get your traverse rods and draperies functional again. Detach the drape panels from the corner bracket to expose the traverse hardware on the side with the broken hangers.
How do you attach a fishing rod to a window frame?
Hang the rod back on the mounting brackets in the window. You might need to pivot, push, or rotate the rod until it clicks into place in the brackets. Replace the screws or bolts if your rod uses them to hold it into the brackets.
How do you hang a traverse curtain rod bracket?
8:4613:21Traverse rod installation quick tips! - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you're going to go out 50 inches put a market 25 inches here and 25 inches and that's where you'MoreIf you're going to go out 50 inches put a market 25 inches here and 25 inches and that's where you're going to hang your ride.
How do you install curtain rod brackets?
0:081:21How to Hang Curtain Rods | The Home Depot - YouTubeYouTubeStart of suggested clipEnd of suggested clipDrill guide holes and use wall anchors for extra. Support fasten the brackets to the wall using aMoreDrill guide holes and use wall anchors for extra. Support fasten the brackets to the wall using a drill or screwdriver. Put the curtain rod in place and make sure it's functioning before finishing.
How do you replace a traverse rod hanger?
1:297:04How to Replace Slides for Traverse Rods for Curtains and Drapes + ...YouTubeStart of suggested clipEnd of suggested clipDown or if you've got this other style which this particular one has all we have to do is pop outMoreDown or if you've got this other style which this particular one has all we have to do is pop out the in bracket where this line pulley is run the carrier. Over drop out the the little hangers.
Where does the bracket go on a curtain rod?
Each bracket should be placed at the height you previously determined and about four to six inches from the side of the window frame. (This will allow you to open the curtains completely.)
How do you install double curtain rod brackets?
0:422:29Lumino 42-120" Double Rod Set Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipEnsure that the brackets are oriented properly place in the desired. Positions and mark the tops ofMoreEnsure that the brackets are oriented properly place in the desired. Positions and mark the tops of both screw hole locations repeat this step for each bracket ensuring they are evenly spaced.
Do you need a stud to hang a curtain rod?
Well, you do NOT need a stud to hang a curtain rod, but you will need a special type of wall anchor to hold the weight. There are two different types I like to use: a drywall anchor or toggle bolts. Because my exterior walls are plaster (similar to drywall) with brick behind, I am going to use the drywall anchor screw.
How do you use a traverse curtain rod?
2:384:24How to Install Pinch Pleat Draperies with Traverse Rod - Outside MountYouTubeStart of suggested clipEnd of suggested clipIt insert the first drapery pin into the first hole of the master carrier followed by the second pinMoreIt insert the first drapery pin into the first hole of the master carrier followed by the second pin into the second hole and so on insert the last pleat into the last ring or glide on the rod.
How do you convert Tab back curtains to traverse rods?
If you want to use a traverse rod, that opens and closes with the pull of a cord, you need to alter your tab-back panels to accept a drapery pin. Just by making a small single-finger pleat, the curtains can accept a pin and hold the folds in place as the curtains are opened and closed on a traverse rod.
How do you remove a hook from a traverse rod?
Press down on the tab on the pulley housing located on either side of the traverse rod if it is a center draw, or one side if it is a single draw. This unlocks the rod so you can easily slide the ring hangers off the rod. Slide the hanger over the housing and lift it out through the hole provided.
Do you need middle bracket on curtain rod?
Center Support Brackets If your curtains cover a lengthy window span, you'll need a functional support bracket in the center to prevent the rod from bowing. Most rods require support brackets every 30 to 36 inches. So if your window is longer than 60 inches across, you'll need two center support brackets.
How far should curtain rod go past window?
As a general rule, drapes will be open during the day, so make sure the curtain rod extends at least four inches on each side of the window's inside frame. To create the illusion of a wider window, extend the rod up to 10 inches beyond the window's frame.
How far should curtain Pole extend beyond window?
This can be subjective and is influenced by obstructions around the window area. But as a guide the pole should extend about 15-20cm (6-8in) beyond the window recess on each side. And it should be fitted symmetrically relative to the window opening.
What is the easiest way to install a curtain rod?
10:1417:32How To Easily Hang Curtain Rods - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what you do is you take your template flush it against the ceiling. And flush it against the edgeMoreSo what you do is you take your template flush it against the ceiling. And flush it against the edge of the window. And mark exactly where you have the intersection or the screw hole that you created.
How do you hang curtain rods inside a window frame?
0:073:02How to Put Up A Curtain Pole In A Window Recess - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you'll need to measure with a tape measure and then you'll need the screwdriver a good idea isMoreAnd you'll need to measure with a tape measure and then you'll need the screwdriver a good idea is to have a spirit level and then you'll need the drill obviously to drill the holes.
How far should curtain rod extend past bracket?
Curtain rods should extend at least 3 to 6 inches past the window frame. Just as hanging curtains above the window frame makes the window appear taller, Bob Vila writes that extending the curtain rod past the window frame makes the window appear wider.
How do you hang a curtain rod without drilling holes?
How to Hang Curtains Without Drilling: 3 MethodsSecure the hardware with adhesive hooks. Adhesive hooks or adhesive strips are versatile hanging tools you can purchase in various sizes and strengths. ... Use magnetic curtain rods.Use tension rod curtains inside window frames.
What is traverse curtain rod?
Things You'll Need. A traverse curtain rod operates curtains with a pulley system. Once the curtain rods are installed and the curtains are connected to the curtain carriers, the curtains are opened and closed by pulling a cord. Most traverse curtain rod kits come compete with all of the hardware necessary to mount the rods above your windows.
How to install a tension pulley on a wall?
Attach the tension pulley to the wall immediately under the cord opening with the provided hardware. Use the cord to open and close the carriers. Locate the knot on the master cord and pull the cord until the other side of the cord is the desired length. Tie an overhand knot and trim the excess cord at the knot. Thread the cord into the cord guide to finish the installation.
How far should I put brackets on a window?
Brackets should be installed approximately 2 inches outside of the window trim and 4 inches above the top of the window. Mark the placement of the screws for the brackets with a pencil.
Can you install brackets in drywall?
Ideally, the brackets should be installed into studs, but this may not be possible. If studs are not available, use hollow-wall anchors to secure the brackets into the drywall. Drill holes and screw the screws into the mounting hardware and the wall.
Step 1: Remove the Drapes
Remove your drapes or curtains from the carriers leaving the hangers, or pins, on the curtains if possible. There is no need to remove the hangers, as you will soon be placing the curtains back onto the carriers.
Step 2: Remove the Curtain Rod
Remove the traverse curtain rod from the mounting bracket. It might have a bolt or screw holding it in place that requires a screwdriver to remove. Traverse rods also typically have cams, which are small plates on the brackets, to hold the rods in place. You might need to turn the cam, either by hand or with a flat screwdriver, to release the rod.
Step 3: Find a Flat Workspace
Place the rod on a flat surface. If you're working with a large rod, it may be necessary to place the rod on the floor, where it can lay flat.
Step 4: Turn the Rod Over
Flip the rod over to expose the back of the rod, the carriers, and the end brackets.
Step 5: Move the Carriers
Slide the carriers that hold your window treatments to one end of the rod. If you have a single string traverse rod, slide the carriers to the side that has the string. If working with a double string traverse rod, slide the carriers on the left to the end next to the left string.
Step 6: Find the Lever
Locate a lever that can be depressed on the end of the rod where the pulleys are located. It's usually metal and simply depresses to allow the carriers to slide off the end of the rod. If there is no such device on your rod, look for a metal device that can be flipped up or down to allow the carriers to be removed.
Step 7: Replace the Traverse Rod Carriers
Slide the carriers off until the one that needs replacing is completely off the traverse rod. Slide a replacement carrier in its place and return the remaining carriers onto the rod by depressing the release or by flipping the release, allowing access to the carriers.
How do traverse rods get their name?
Traverse rods get their name from the draperies that travel across the rod via a pulley or wand, depending upon the rod's hardware setup . Some traverse rod hardware operates via a side draw, while others use a center draw.
Can you put ring hangers on a rod?
This creates an opening through which you can remove and replace hangers. Add extra plastic ring hangers onto the rod, even if you don't need them.
Do you need to remove a traverse rod?
If the traverse rod bracket uses screws to keep the rod attached to the corner hardware, remove the screws and set them on a small plate so you do not lose them.
