how do you install a washing machine drain pump

How to Replace the Drain Pump of Your Top-Load Washer

Full Answer

How to make a washing machine drain properly?

To operate your machine and achieve the best results, we ask you to follow these simple guidelines:

• Close your water mains and open up the washer door before starting the machine. This will allow the drum to fill with water and drain properly.
• Add detergents or powder into the drum using a scoop or drawer.
• Make sure that your laundry is evenly distributed inside the drum for a more energy-efficient wash.

How to properly install a washing machine?

Washing machines are easy to install if you are replacing an old unit with a new one. As long as you already have the necessary plumbing ready, installing a washing machine only requires you to make the right drain and supply connections, level the washer and plug it in.

What would make a washing machine not spin or drain?

Try These Easy Fixes

• Common Reasons a Washer Won’t Spin. In this post, we’ve outlined the most common reasons a washer won’t spin. ...
• Drive Belt. Your washing machine’s drive belt helps the motor power the spin of the drum by wrapping around the motor and a pulley wheel.
• Drive Motor. ...
• Motor Coupler. ...
• Lid Switch. ...
• Broken Pump. ...
• Repair Costs When a Washer Won’t Spin. ...
• Washer Won’t Spin? ...

How to fix a washing machine to drain completely?

Plug In the Washer and Start a Normal Cycle

• Plug the washing machine back in and start a normal cycle.
• As it fills, watch for any signs of a leak. If you see water leaking from the washing machine, press the cancel button. ...
• If it passes the leak test, start a spin cycle to test the drain.

How to access washer gasket?

How to remove the front control panel on a washer?

How to remove detergent drawer from washer?

How to remove a spring from a gasket?

How long does it take for a washer to drain?

How to remove old pump from a septic system?

Where is the drain hose on a washing machine?

See 2 more

Is it easy to replace a washing machine pump?

Replacing the pump in a washing machine is a surprisingly simple job that most moderately handy people can accomplish within an hour or so and with basic parts and tools. The process and steps used are also the same ones used when simply cleaning out the pump or hose in the event of a clog.

Where is the washing machine drain pump located?

The drain pump is located at the bottom of your washing machine, but can be easily accessed in order to replace it if need be. If your washing machine is failing to drain during a wash cycle, it could be that there is a problem with the drain pump.

How much does it cost to replace a washing machine drain pump?

On average, expect to spend $300 to $400 for a pump replacement job. Washing machine pump repairs are usually required when you note active leaks or a tub that doesn't drain. If the tub does not move, but the agitator does, this indicates the pump is starting to experience issues.

How do I know if my washing machine drain pump is working?

Put your finger into the drain outlet and feel the impellers if the pump freely turns. One or more of them may be broken. If so, you'll be able to feel them while you're turning the pump flywheel with your other hand. You also may see broken pieces of plastic in the bottom of the pump housing.

How long do washer drain pumps last?

How Long Do Washing Machine Pumps Last? Depending on the drain pump quality, you can expect it to last anywhere from 3 to 5 years. However, it's not uncommon for drain pumps and other washer components to last upwards of 10 years.

Why do washing machine drain pumps fail?

A pump can fail in two ways: mechanically and electrically. A mechanical failure can be caused by a foreign object caught in the pump, or direct damage to a pump component, such as the impeller. Inspecting the pump can often reveal a mechanical failure. An electrical failure can be diagnosed by using a multimeter.

Is it worth repairing a 7 year old washing machine?

As a general rule, if it costs less than 50% of the price of a new washing machine to repair your old one, you should choose the repair option. But, you should also consider whether or not there is a warranty coverage on your washer and think about economic realities.

Why is my washing machine making a really loud noise when spinning?

Rumbling, very noisy spin Most often, this is caused by drum bearing failure. One way of testing is by spinning the drum by hand. If it's noisy, the bearings will need replacement. The second, and easier way of testing is by trying to lift the drum from just behind the top of the door.

Why is my washing still wet after spinning?

A full or partial blockage in the filter or pump will affect your washing machines ability to drain water from the drum. This will lead to poor rinsing results and soaking wet clothes at the end of the cycle.

How do you clear a clogged washing machine pump?

0:111:57How do I unblock my washing machine pump? - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou may find obstructions in the filter such as coins or a buildup of lint. These should be removedMoreYou may find obstructions in the filter such as coins or a buildup of lint. These should be removed before thoroughly cleaning the filter carefully check if the impeller moves freely.

How do you test a washing machine drain?

To test this, remove the drain hose attached to the washer and make sure it is clear. An easy way to check that the drain hose is clear is to blow air through it. If nothing is obstructing the drain tube, the problem is most likely at the washing machine pump.

Should a washing machine drain pump spin freely?

It should move freely. However, some impellers may feel like there's a small resistance which when overcome allows the impeller to jump 180 degrees round.

How do you unclog a drain pump?

2:113:17Washer Repair: How to Unclog the Drain Pump - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's very easy to remove it you simply pop these two spring clips. Off. Choose a flat bladeMoreIt's very easy to remove it you simply pop these two spring clips. Off. Choose a flat blade screwdriver release the spring clips you can slide the pump.

How do I know if my washing machine drain hose is clogged?

Drain Hose Problems To test this, remove the drain hose attached to the washer and make sure it is clear. An easy way to check that the drain hose is clear is to blow air through it. If nothing is obstructing the drain tube, the problem is most likely at the washing machine pump.

How do you unblock a washing machine waste pipe?

Use a funnel to pour about a quarter of a cup of baking soda into the pipe. Next, empty a baster full of vinegar into the drain hose. Top tip: If the blockage is not completely gone, you can repeat the above process. Once you have cleared any debris from the hose, pour hot water in to flush everything out.

How do I clean the pump filter on my washing machine?

0:361:51How to Remove and Clean the Pump Filter in your Washing MachineYouTubeStart of suggested clipEnd of suggested clipUnscrew this lid here move it slightly from side to side and pull the filter out water normally goesMoreUnscrew this lid here move it slightly from side to side and pull the filter out water normally goes through these little holes here. And into the back of the drain pump. And then down to the drain.

How to access washer gasket?

You can access the gasket by opening the washing machine door. The rubber seal around the opening of the washer is the gasket, and it is held in place by a metal clamp — a round metal wire secured by a spring.

How to remove the front control panel on a washer?

Remove the front control panel. Start by removing the detergent drawer completely if your washer has one. There should be a button or tab in the back of the drawer that you can press to release the drawer and pull it all the way out. Set this aside and remove the mounting screws securing the panel.

How to remove detergent drawer from washer?

There should be a button or tab in the back of the drawer that you can press to release the drawer and pull it all the way out. Set this aside and remove the mounting screws securing the panel. On the model featured in our repair video, these screws are found in the same compartment as the detergent drawer.

How to remove a spring from a gasket?

Locate the spring — it should be on the bottom of the gasket — and use a flat head screwdriver to gently pull it away from the gasket. Slide the screwdriver in from the top of the spring to avoid damaging the gasket and carefully work the spring and the attached clamp out of the groove it’s snapped into to remove it.

How long does it take for a washer to drain?

Drain the washer tub. Some washers will automatically drain after being unplugged for around five to ten minutes, so it’s not a bad idea to let the appliance sit for a bit before moving on if it’s still full of water. Otherwise, you’ll need to either bail out the tub or manually drain it with the emergency drain hose.

How to remove old pump from a septic system?

The old pump will be attached to the assembly by a few mounting screws and should be easy to remove once those are unscrewed. Once it’s off, grip the pump to pull it out of the plastic cover. You can slide the new pump back into the cover and attach it to the assembly.

Where is the drain hose on a washing machine?

The drain hose is accessed from a panel on the front of the washing machine, usually toward the bottom.

Why install a drain pan on a washing machine?

Installing a washing machine drain pan is a great way to prevent your washer from leaking water onto your laundry room floor. Also, lest you shy away from this job because of its perceived difficulty, you'll be pleased to learn that installing a washing machine drain pan can be a piece of cake, especially if you tackle the job with ...

What is the purpose of articles being reviewed?

To ensure our content is always up-to-date with current information, best practices, and professional advice, articles are routinely reviewed by industry experts with years of hands-on experience.

Can you move a washing machine on a dolly?

For this task, you may want to incorporate the aid of a second person to help you lift your washing machine onto a dolly so that it can be easily moved. After you've successfully moved your washer and uncovered your floor drain, you'll be free to move on to the next step.

How to access washer gasket?

You can access the gasket by opening the washing machine door. The rubber seal around the opening of the washer is the gasket, and it is held in place by a metal clamp — a round metal wire secured by a spring.

How to remove the front control panel on a washer?

Remove the front control panel. Start by removing the detergent drawer completely if your washer has one. There should be a button or tab in the back of the drawer that you can press to release the drawer and pull it all the way out. Set this aside and remove the mounting screws securing the panel.

How to remove detergent drawer from washer?

There should be a button or tab in the back of the drawer that you can press to release the drawer and pull it all the way out. Set this aside and remove the mounting screws securing the panel. On the model featured in our repair video, these screws are found in the same compartment as the detergent drawer.

How to remove a spring from a gasket?

Locate the spring — it should be on the bottom of the gasket — and use a flat head screwdriver to gently pull it away from the gasket. Slide the screwdriver in from the top of the spring to avoid damaging the gasket and carefully work the spring and the attached clamp out of the groove it’s snapped into to remove it.

How long does it take for a washer to drain?

Drain the washer tub. Some washers will automatically drain after being unplugged for around five to ten minutes, so it’s not a bad idea to let the appliance sit for a bit before moving on if it’s still full of water. Otherwise, you’ll need to either bail out the tub or manually drain it with the emergency drain hose.

How to remove old pump from a septic system?

The old pump will be attached to the assembly by a few mounting screws and should be easy to remove once those are unscrewed. Once it’s off, grip the pump to pull it out of the plastic cover. You can slide the new pump back into the cover and attach it to the assembly.

Where is the drain hose on a washing machine?

The drain hose is accessed from a panel on the front of the washing machine, usually toward the bottom.