Steps:
- Remove door.
- Pull old rollers and pivots out of door with pliers.
- Remove old door track with drill.
- Cut new door track to length, if necessary.
- Install new door track, centered on the doorjamb, by screwing into the doorjamb with screws provided in the kit.
- Snap the new rollers and pivots into the door.
Full Answer
How do you install carpet under a sliding closet door?
A few carpet fibers will stick to the drill bit; pull them off after drilling each hole. Secure the bracket track to the subfloor by screwing loosely into place, using screws that are 1/2 inch longer than those that came with the sliding doors. Tighten down the screws uniformly.
How do you install tackless carpet around a door?
Using a stair tool, tuck the carpet down into the gap between the tackless strips and the wall. At the doorway, trim the carpet so the edge is centered under the closed door and install a door edge strip. Finally, cut any vent openings and reinstall the molding on the baseboards.
How do you install a door guide under carpet?
If the floor under the carpet is concrete, use a drill to make an installation hole (skip if you have a wooden floor). Test the door guide by opening and closing the door. Make sure that the guide has a strong position on the floor.
How to install a sliding closet door with rail?
Measure the opening width of the door (for a sliding closet door with rail), leaving 1 inch (about 2.5cm) of overlap to accommodate the door guide. Mark the spot where the two-door panels overlap. Use wood screws to install the guide in place. Pick the screws that are slightly longer than 1 inch to accommodate the carpet’s thickness.
What is a closet door guide?
What is a guide on a carpet?
How to test a door guide?
Does a closet door guide need a railing?
Bypass closet door track on carpet? | DIY Home Improvement Forum
Not sure but maybe I should have posted this in the flooring forum... I think maybe I could cut a long slit in the carpet where the track will go and remove a section of the padding, than put the carpet back and lay the track on top of the carpet and nail or tapcon in place..
Attach bypass closet door guide through carpet to concrete
I have a set of bypass closet doors and need to attach the little guide in the center to the floor. The floor is carpet and pad over concrete. My basic idea is to attach a piece of 1/2" oak to the floor on top of the carpet by drilling holes through the carpet into the concrete with a hammer drill, drop in sleeves, then screw the oak and the guide to the concrete over the carpet all in one shot.
Carpet and Closet Door Guide - Fine Homebuilding
I have come to you guys for help before, and you have always been very helpful. I have a new problem: replacing a broken sliding door guide–the kind that fits on the floor in the small space where the hanging doors overlap and help guide each door.
Sliding Closet Doors Over Carpet - DoItYourself.com
Doors, Skylights and Windows - Sliding Closet Doors Over Carpet - Our master bedroom previously had a bare wood floor but we decided on carpeting. The closet doors are sliding doors, the kind where there's a metal track along the top of the opening and two doors are hung by rollers on that track. I believe they're
How to cut a track with a hacksaw?
Insert a 2-by4-inch wooden board into both the track's front and back grooves, so that you don't bend them during the cutting process. Cut through each marker line using a hacksaw and a metal cutting blade. Discard the unneeded track portions.
What is sliding closet door?
Sliding closet doors cover openings that are wider than a standard single door, and they come in a variety of colors and materials. They all function using a series of upper and lower tracks allowing the two panels to slide back and forth over each other. Installing sliding closet doors requires attaching the tracks and slide ...
What is a carpet stretcher?
This will stretch the carpet over the tackless strip where the tacks will grab it and hold it firmly in place. A carpet stretcher will finish attaching the carpet. A carpet stretcher is similar to knee kicker, but much longer.
How to put underlay down?
Butt the strips against each other—don't overlap them—then staple the underlay down along the inside edge of the tackless strip. Trim the excess underlay along the inside of the tackless strip and use duct tape to seal the seams.
How does carpet shrink?
A wall-to-wall carpet will shrink and expand with changes in temperature and air pressure. If you bring a carpet in from outside and install it right away, as the carpet adjusts to the conditions inside your home it may stretch and shrink away from the tackless strips, or may expand toward the walls and wrinkle and buckle in the middle. To prevent this, allow the new carpet to rest, uninstalled, in the room for at least 24 hours. It will adjust to your conditions and remain true to the dimensions you cut it to.
Is it rocket science to install wall to wall carpet?
Installing wall-to-wall carpet isn't rocket science. By using some specialized tools (available at most tool rental outlets) and being prepared to take your time, it can even be a DIY job.
How high should a closet door be from the ground?
According to experts, the standard height of a closet door from the ground should be about 80 inches – this is about the same height as that of a standard entry door.
Do you install closet doors before or after carpet?
Flooring installation is, no doubt, an essential part of your interior design project. If done well, it can easily make your space and improve your home decor. When it comes to flooring your bedroom, there are several different flooring ideas that you can opt for. Some of the best and main types of flooring include laminate, hardwood, porcelain, natural stone, vinyl, and carpet.
Step 1
Align the bracket track on the floor as per sliding door installation instructions; typically, the top door rail is installed and the doors hung to find the exact positioning of the floor bracket.
Step 2
Mark the screw-hole locations through the track, using a black fine-point marker to mark the spots on the carpet.
Step 3
Drill starter holes through the carpeting, pad and subfloor, using a drill bit size recommended by the door installation instructions or one size smaller than the screws. A few carpet fibers will stick to the drill bit; pull them off after drilling each hole.
Step 4
Secure the bracket track to the subfloor by screwing loosely into place, using screws that are 1/2 inch longer than those that came with the sliding doors.
Step 5
Tighten down the screws uniformly. The bracket track will now be installed solidly to the carpeted floor and will not shift.
What is a closet door guide?
A door guide is small but important, keeping your sliding door firmly in its place. Knowing how to install closet door guide on a carpet will free you from straying door panels. A properly installed guide also keeps your closet door in top shape. Make sure you know what to expect when deciding to install a guide yourself.
What is a guide on a carpet?
The guide has a shape like a half-circle, giving it a more elegant look. The shape also reduces the risk of fiber snagging on a floor with long carpet fiber. The sides “press” the fiber as you slide the door panel, preventing a snag from occurring.
How to test a door guide?
Test the door guide by opening and closing the door.
Does a closet door guide need a railing?
The guide moves seamlessly with the door, keeping it from swinging freely. This simple door guide doesn’t require a railing so that you can use it for a simple closet on a carpeted floor.
