DECKORATORS FASCIA INSTALLATION INSTRUCTIONS Attach fascia to the rim joist using 3 screws spaced no further apart than 16” on-center. Fasten the fascia from one end to the other, or from the center out to each end. Never fasten the fascia from both ends to the center. Leave a 1/8” space between the fascia ends where two pieces meet or
How to install joists for a deck?
Method 2: Installing hangers
- Pull and mark layout across the face of the rim joist using a square to extend the lines from top to bottom.
- Align a joist hanger with a scrap of lumber to the layout lines and flush with the joist top.
- Depress the hanger tab to hold the joist in the right position.
- Drive 11⁄4-in. Teco nails through the hanger holes to secure it to the rim joist.
How to install Trex decking from the underside?
- Make all joists straight and square.
- Add outlets to the gutter every 12′ – 14′.
- Cover all joists and blocking with trough material, then tape.
- Finally, cover the Trex RainEscape system with deck boards.
- Ensure the troughs and downspouts are dry and clear of debris before applying tape.
How to install composite deck railings?
Installing the Railings
- Slide on the Post Sleeves. Slide on the post sleeves. ...
- Secure the Post Sleeve Collars
- Measure and Mark the Bottom Rail
- Measure and Mark the Top Rail
- Cut the Rails
- Secure a Crush Block
- Trace the Bracket Position on the Posts
- Drill the Pilot Holes
- Attach the Brackets
- Attach the End Balusters
How to install railing on deck?
Part 4 Part 4 of 4: Installing the Rail
- Secure the bottom rail to the posts. Use a couple of scraps of wood to hold the bottom rail up at the height you want it to be.
- Set the balusters assembly on the bottom rail. Position the thin strip holding the balusters together on the center of the bottom rail.
- Lay the top rail down. ...
- Repeat for other sections of railing. ...
How do I install Deckorators post?
4:215:13Installing the Deckorators Grab & Go Classic Composite Railing - YouTubeYouTubeStart of suggested clipEnd of suggested clipCheck the rail for level using the bracket as a guide mark the screw positions on the post sleeveMoreCheck the rail for level using the bracket as a guide mark the screw positions on the post sleeve and rail on both ends pre-drill 1/8 inch pilot holes through the post sleeve and rail attach.
How do you install Deckorators on a stair rail?
4:255:20Installing the Deckorators Grab & Go Classic Composite Stair RailingYouTubeStart of suggested clipEnd of suggested clipPlace the brackets. And covers on the top rail then carefully position it between the posts. WorkingMorePlace the brackets. And covers on the top rail then carefully position it between the posts. Working the balusters. Into the routed holes from one end to the other.
How do you install Deckorators on an aluminum railing?
2:135:37Installing the Deckorators Contemporary Aluminum RailingYouTubeStart of suggested clipEnd of suggested clipPre-drill holes on the bottom of the lower rail for the support blocks. Use a 1 8 inch. Bit attachMorePre-drill holes on the bottom of the lower rail for the support blocks. Use a 1 8 inch. Bit attach the brackets. And then the blocks. Themselves.
How do you install Deckorators stair balusters?
1:182:58How to Install Deckorators Balusters - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe can screw the ballast or connector into place then screw your rail connectors into your railsMoreWe can screw the ballast or connector into place then screw your rail connectors into your rails ensuring that they're tightly secured.
Can you cut Deckorators railing?
Railing posts cannot be more than 6 feet apart (on-center). Once you've determined that the posts are good to go, you'll need to trim the post sleeves to length with a chop saw or circular saw. A carbide-tipped blade works best.
How high should a post be above the railing?
Measure from the deck floor to the top of the rail between posts. This must be at least 36" high to meet IRC requirements. Make sure your sweep space and all infill openings will not allow a 4" sphere to pass through.
Are Deckorators railings good?
All Products. Deckorators® products are as strong and highly functional as they are attractive. Each is smartly engineered, made of top-quality materials and durably coated for greater protection against the elements, assuring year after year of lasting beauty with minimal care.
How do you cut Deckorators for decking?
For Wood Plastic Composite Decking: • Use fine tooth carbide trim blade to cut. Use a sharp utility knife or jigsaw to finish cuts where a circular saw cannot fully complete cut. (Marking on the back side when needed.)
How do you install deck railing with metal balusters?
2:006:09How-to Install: Round Balusters for Deck Railings | Nuvo Iron - YouTubeYouTubeStart of suggested clipEnd of suggested clipTogether measure the section and divide it in half to find the center point of the railing. And markMoreTogether measure the section and divide it in half to find the center point of the railing. And mark this spot next we'll install the smdra baluster connectors for most sections.
How do you attach stair balusters?
5:577:15How To Install Iron Balusters - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo that any epoxy that comes out of the hole will stick to the tape instead of the baluster. RepeatMoreSo that any epoxy that comes out of the hole will stick to the tape instead of the baluster. Repeat this step for each of your balusters. In this run. Allow the balusters to sit for up to 24.
How do you connect balusters?
0:291:51Square Top Balusters on Open Tread Stair Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipPlace a small amount of wood glue into the holes. Place the balusters pin in the hole. And swing theMorePlace a small amount of wood glue into the holes. Place the balusters pin in the hole. And swing the balusters top into position in the hand rail plow.
How do you screw a baluster?
1:044:30Cooper Stairworks Tips & Techniques - Installing Balusters ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipCut that pin right off mock your Center and drill a three sixteenths pilot hole in for the bolt.MoreCut that pin right off mock your Center and drill a three sixteenths pilot hole in for the bolt. There's a special driver that holes the threaded end of the lag kite up against in the truck.
How do you cut Trex Enhance railing?
What do you use to cut Trex railing? Trex recommends using a miter saw with the Trex Blade or a carbide-tipped blade with 60 teeth or more.
How do you cut Deckorators for decking?
For Wood Plastic Composite Decking: • Use fine tooth carbide trim blade to cut. Use a sharp utility knife or jigsaw to finish cuts where a circular saw cannot fully complete cut. (Marking on the back side when needed.)
Welcome Kit Sign-up
Once you've completed your Deckorators deck project, sign up to receive your free welcome gift.
Warranties
We stand firmly behind our products with some of the best, first-of-their-kind product warranties in the industry.
Literature
Find all Deckorators product literature including style guides and technical information.
Installation Instructions
How do I put this together? How does this connect to... that? Here's how!
Baluster Calculator
Use our baluster calculator to quickly determine how many balusters or spindles you need for your project.
News & Events
Learn more about Deckorators by taking a look at our News & Events section.
Who makes Deckorators decking?
Deckorators wood-plastic composite (WPC) decking, manufactured by UFP Ventures II, In c have been evaluated by an independent 3rd party evaluation report writer known as PFS-TECO to be code compliant under PFS-TECO’s RR-0100 Evaluation Report. See report for complete details. For projects in Canada, please refer to NRC-CNRC Evaluation Report CCMC 13378-R .
What is deckorators made of?
Deckorators Trailhead , Heritage, Vista and Classic Composite Decking lines are made of wood and plastic, and is co-extruded with a durable polyethylene top layer for ultra low-maintenance performance.
How far should decking be on joists?
In residential applications, Deckorators decking should be installed on joists spaced 16 " on-center when the boards are running perpendicular to the support joists. Decking boards running on a diagonal pattern should be installed on joists spaced 12" on-center. Contact Deckorators Customer Service team at 800-556-8449 for commercial applications. For more details, refer to the installation instructions.
Why do decks mushroom?
Because wood decking is not as dense as Deckorators, screws driven into wood decking crush the wood fiber and self countersink. Screws driven into Deckorators displace the material, causing it to mushroom around the screw head. Most consumers do not like the resulting appearance using this installation method.
How much gap between deck boards?
Allow a 1/4" gap between the deck boards and between all decking and any permanent structure or post for water runoff. For more information, refer to the installation instructions.
What is the traction of a voyage deck?
Voyage Decking provides 34% or greater surface traction than other leading brands of composite decking. This capped deck board has been tested by an independent third-party lab between 9/24/18-9/25/18 in wet conditions under the Australian – New Zeeland AS/NZS 4586-2013 standard.
How long is Deckorators' warranty?
Deckorators Voyage, Vault and Frontier Decking have a stain- and fade-resistant cap stock and are backed the industry's best warranty: 50-year Structural, 25-year Stain & Fade and 25-year Removal & Replacement.
