How do you install Gator dust?
- Install the wetcast or natural stones on a maximum 1” (2.5cm) bedding sand.
- Hit the westcast or natural stones with a rubber mallet; this will make the Gator Dust settle firmly into the joints by removing any air pockets.
- Shower a specific 50 sq.
How do you use Gator dust on stone?
If you’re using natural stone, sweep the Gator Dust in between the full depth of the joints using a hard-bristle broom. If you’re using wetcast stone, carefully pour the Gator Dust in between the full depth of the joints.
What temperature can Gator dust be used at?
Installing in Inadequate Temperatures Gator Dust is engineered to be installed at temperatures above 59 degrees Fahrenheit. If installed at lower temperatures, it may never set up and function as it is intended to. 6. Improper Use Gator Dust should only be used for pedestrian applications.
Should I use Gator dust on my joints?
Should this happen, you will need to be patient and give the joints time to dry before evaluating. In most cases, if the Gator Dust has not washed out of the joints and appears to be hardening, you’ll probably be ok. If the joints are not hardening, it’s back to square one. 3. Overfilling the Joints
What happens if it rains after installing Gator dust?
Attempting a Gator Dust install in unpredictable weather is a bad idea. If it rains within 24 hours after your installation, you run the risk of the material not setting up properly or even washing out of the joints. Should this happen, you will need to be patient and give the joints time to dry before evaluating.
How long does it take Gator dust to set?
24 hoursGator Dust requires 24 hours on a conventional drainage base, it is not for use on overlays.
Does Gator dust get hard?
When installed properly, this product will become incredibly firm, locking the stone joints while still retaining flexibility and durability.
How many bags of Gator dust do I need?
One bag of 50 lbs (22.7 kg) of this product will cover between 20 to 30 square feet (1.86 to 2.79 sqare meter) if the joints are about 1” to 2” (2.54 to 5.08 cm) wide and the stones are about 2” to 2-1/2” (5.08 cm to 6.35 cm) thick.
How much does a bag of gator dust cover?
between 20 to 30 square feetOne bag of 50 lb of this product will cover between 20 to 30 square feet if the joints are about 1" to 2" wide and the wetcast or natural stones are about 2" to 2-1/2" in height. GATOR DUST is recommended for a variety of uses, including patios, walkways and pool decks.
Should you seal pavers before polymeric sand?
Traditionally, concrete paver manufacturers have recommended waiting at least 90 days after polymeric sand installation to apply a protective sealant to a paver surface.
When should you not use polymeric sand?
#6 - Too Narrow or Too Wide Joints The sand is simply pushed out of the joints. This is why we don't recommend using polymeric sand on extremely narrow joints. Similarly, too-wide joints can lead to washout, because they allow too much water flow during the activation process.
How do you remove Gator dust residue?
Using a leaf blower, blow off all Gator Dust residues lying on the stone surface. Depending on the physical layout present, it may be more appropriate to remove residue by using a vacuum unit.
How do you sweep polymeric sand?
2:025:20How to use Polymeric Sand - YouTubeYouTubeStart of suggested clipEnd of suggested clipHold the bag close to the surface to minimize airborne dust. Step 3 with a broom sweep the sand intoMoreHold the bag close to the surface to minimize airborne dust. Step 3 with a broom sweep the sand into the joints until they are completely filled.
When can you walk on polymeric sand?
A minimum of 24 hours drying time is required prior to allowing significant foot traffic and 48 hours for vehicular traffic on the paver surface. Polymeric sands are designed to soften and re-heal.
How long does Gator seal last?
2 to 5 yearsNormally a sealer is reapplied in 2 to 5 years, depending if it has visibly worn. When reapplying a Sealer, it is recommended to use Gator Resealer, particularly for an existing solvent-based sealer.
How do I install Gator Maxx polymeric sand?
2:164:36How to install Gator Maxx Polymeric Sand - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst with a hard bristle broom then a soft bristled broom take care to leave the height of theMoreFirst with a hard bristle broom then a soft bristled broom take care to leave the height of the polymeric sand at least one eighth of an inch below the edge or chamfer of the pavers.
How many square feet does a 50 lb bag of polymeric sand cover?
When filling small gaps, a 50lb bag of polymeric sand will usually cover 75-100 ft2. When filling wide gaps of 1/4″ to 3/8″ a 50lb bag will usually cover 30-60 ft2. Wider gaps, for example with a flagstone patio, will require even more sand to fill.
How to fix gator dust?
1. Under-watering. Under-watering results in the Gator Dust not setting up properly. Depending on how much time passed since the dust was first activated, you may be able to resolve the issue by letting your sprinkler run on it for about an hour.
How long does gator dust last?
Found this. “ Gator Dust is rainproof in 24 hours in temperatures above 59 degrees Fahrenheit … and that’s a minimum temperature for 24 hours; not the high of the day!”. No, Gator Dust is a jointing material only and meant for natural stone joints from 1/2” - 6” wide.
What is gator dust bond?
Gator Dust Bond is a unique mixture of polymer binders and calibrated stone specially formulated to strengthen the joints of any pedestrian natural stone application. When installed properly, this product will become incredibly firm, locking the stone joints while still retaining flexibility and durability.
Can gator dust be hardened?
In most cases, if the Gator Dust has not washed out of the joints and appears to be hardening, you’ll probably be ok. If the joints are not hardening, it’s back to square one. 3. Overfilling the Joints. Overfilling the joints on a natural stone project can lead to damage down the road.
Is it bad to install gator dust?
Attempting a Gator Dust install in unpredictable weather is a bad idea. If it rains within 24 hours after your installation, you run the risk of the material not setting up properly or even washing out of the joints. Should this happen, you will need to be patient and give the joints time to dry before evaluating.
Can gator dust be used on pavers?
Gator Dust should only be used for pedestrian applications . It does not have the compressive strength to resist the tremendous loads placed on the joint, by a vehicle. And Gator Dust should never be used with dry-cast pavers. (It can be used with some wet-cast products.)
Can you mix sand with gator dust?
Mixing in Regular Sand. We do not recommend using regular sand to halfway fill the joints of a Gator Dust project. Without a firm, densely-packed base, water and ice can work their way into the joints and cause the Gator Dust to fail.
IMPORTANT INSTALLATION NOTES
Always refer to the latest GATOR DUST BOND Technical Data Sheet (TDS) at AllianceGator.com before installing GATOR DUST BOND.
REQUIRED SUB-SURFACE PREPARATION
GATOR DUST BOND is recommended for a variety of uses, including patios, walkways and pool decks. The wet cast or natural stones must be installed on a traditional base system: maximum of 1″ (25 mm) of bedding sand, plus a minimum of 6″ (15 cm) of crushed stone compacted at 98% Proctor density. (See diagram 1 below).
GATOR DUST BOND INSTALLATION STEPS FOR A NEW WET CAST OR NATURAL STONE SURFACE
Install the wet cast or natural stones on a maximum 1″ (25 mm) bed of sand. Make sure that there is at least 6″ (15 cm) of compacted crushed stone under the bedding sand. See diagram 1.
IMPORTANT
The water used in step 6 will activate a bonding action as well as condensing GATOR DUST BOND in the joints. Too much water will undo the dense compaction obtained during step 3 and reduce the final performance of GATOR DUST BOND.
Hello!
We use cookies to help improve your experience. By continuing to use this website, you agree to our Privacy Policy.
