How to Install Interlocking Brick Edges for Garden
- 1. Dig a 4-inch-wide, 8-inch-deep trench along the outside edge of your landscaping area, using a hoe or narrow shovel. ...
- 2. Fill the bottom of the trench with 3 inches of gravel and pack it down with your foot. ...
- 3. Add 2 inches of sand on top of the gravel and pack down.
Full Answer
How to install interlocking brick edges for garden?
How to Install Interlocking Brick Edges for Garden 1 Dig a 4-inch-wide, 8-inch-deep trench along the outside edge of your landscaping area, using a hoe or narrow shovel. 2 Fill the bottom of the trench with 3 inches of gravel and pack it down with your foot. ... 3 Add 2 inches of sand on top of the gravel and pack down. More items...
How do you interlock edging on pavers?
Some types of edging interlock, as shown here; others (such as galvanized metal edging) should be overlapped by a few inches where the pieces meet. Secure the overlapped ends and all single ends with a long edging spike or staple, as applicable. Continue installing edging along the full length of the paver line, as desired.
How do you measure for interlocking pavers?
You need to determine the square footage of the area that interlocking pavers will cover. To get information, measure the width and length of the area and multiply it to get the result. There is no perfect measurement, thanks to all the specific angles and curves in your design.
How deep do you dig to install brick pavers?
Installing the bricks is straightforward, but requires some border preparation before setting the bricks. Dig a 4-inch-wide, 8-inch-deep trench along the outside edge of your landscaping area, using a hoe or narrow shovel.
What is interlocking brick?
Where do you fill in the trench?
About this website
What is an edge restraint?
Edge restraint is going to prevent lateral movement of our project. Depending on the base material that is used, you will opt for a matching edge restraint. When we are talking about an open graded base, we are going to use a concrete edge restraint. When installing this, we will scrape away that one inch bedding layer and then install a tapered concrete edge with a trowel up to an inch up the paver so that it is covering that one inch bedding layer plus one inch up our paver.
How much overlap is needed for geotextile?
When installing the geotextile, we are going to roll it out on our project and ensure that there’s at least a twelve inch overlap from piece to piece while making sure that it is shingling away from the foundation. This makes sure that any water that gets on it is going away from the foundation and not going underneath another piece of fabric. We can then start with our base preparation.
What to do with slope of patio?
This may include having to build a retaining wall to allow you to get a flat surface for your walkway. Same thing goes for a backyard patio, if your slope of your backyard is extremely steep, you may need to build a retaining wall to be able to level out that area to give you a usable patio. For the purpose of this article, we are going to be only talking about patios that are built on grade or walkways, driveways, being able to lay them exactly as-is with the slope of the yard. Learn more about raised patios.
How to secure galvanized metal edging?
Some types of edging interlock, as shown here; others (such as galvanized metal edging) should be overlapped by a few inches where the pieces meet. Secure the overlapped ends and all single ends with a long edging spike or staple, as applicable. Continue installing edging along the full length of the paver line, as desired.
What is the best tool for digging a trench?
A mattock is the perfect tool for digging a flat, narrow trench. It comes in both small short-handled and large long-handled versions. The smaller tool is easier to swing, while the larger version packs more punch.
How to measure for pavers?
To calculate the trench depth, start with the paver height, subtract the height above ground that the pavers will sit, then add 1 to 2 inches for the sand layer . For example, if the paver is 3 1/2 inches tall and will sit 1/2 inch above the ground, the trench should be: 3 1/2 – 1/2 + 2 = 5 inches (with a 2-inch sand layer).
What type of pavers are best for mowing strips?
Precast concrete pavers with an interlocking-end connection system are an excellent choice for a mowing strip. The pavers shown in this project are 3 1/2 x 12-inch units from Edgestone. These have rounded ends so the pavers fit together for extra stability. The design also allows the pavers to form curves without having large triangular gaps on one side of the edging, like you would get with standard rectangular paving bricks. These pavers are also much heavier and taller than most paving bricks, so they're more likely to stay in place.
What is interlocking brick?
Interlocking brick edging creates a decorative border that prevents weeds and grass from entering plant areas, while at the same time defining the landscaping with a continuous row of brick work. The interlocking pavers, placed upright around the plant beds, intertwine together and support each other to prevent any one paver from falling down or shifting out of place. Installing the bricks is straightforward, but requires some border preparation before setting the bricks.
Where do you fill in the trench?
Fill in the trench at the ends of the brick border.
