Fit the Oz-post onto the driving mandril and locate the tip of the Oz-post over the insertion point. Raise the entire assembly to vertical using the Oz-post as a pivot. Drive the Oz-post into the ground a short distance until it supports the Jackhammer (usually 100mm or so is sufficient).
How do you use an Oz post support?
Lie the jackhammer on the ground with the driving mandril pointing towards the installation point and approximately the length of your Oz-post support distant from it. Fit the Oz-post onto the driving mandril and locate the tip of the Oz-post over the insertion point. Raise the entire assembly to vertical using the Oz-post as a pivot.
What is an Oz-post?
The Oz-Post™ is a post anchor for use when erecting all types of fences, sign posts or decks. The Oz-post™ is suitable for steel, wood and plastic posts. Many round, square, and rectangular cross sections can be accommodated.
How do you use an Oz post for a jackhammer?
Fit the Oz-post onto the driving mandril and locate the tip of the Oz-post over the insertion point. Raise the entire assembly to vertical using the Oz-post as a pivot. Drive the Oz-post into the ground a short distance until it supports the Jackhammer (usually 100mm or so is sufficient).
How long does it take to install an Oz-post™?
An Oz-Post™ can be easily installed in less than four minutes by only one person. The dramatic time savings compared to traditional methods will provide for a cost reduction and significant improvements in labor efficiency.
How do I anchor a post to the ground?
0:091:07How to Anchor Wood Posts : Woodworking Tips - YouTubeYouTubeStart of suggested clipEnd of suggested clipYour post on top of that for drainage. Mix a bag of ready mix concrete. Into a wheelbarrow withMoreYour post on top of that for drainage. Mix a bag of ready mix concrete. Into a wheelbarrow with water pour. Another six inches of concrete into the whole. Level the post plumb.
How do you install galvanized posts?
1:213:00Lifetime Steel Post™ Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipCut a wood or composite board to your chosen top rail measurement. And attach that board through theMoreCut a wood or composite board to your chosen top rail measurement. And attach that board through the pre-drilled holes in the lifetime steel post remember to use steel to wood screws.
How do I install bolt down post support?
0:311:21How To Install a Fence Post Onto a Concrete Base - YouTubeYouTubeStart of suggested clipEnd of suggested clipRemove the base and then drill into the concrete using a hammer drill. And masonry drill bits. MoveMoreRemove the base and then drill into the concrete using a hammer drill. And masonry drill bits. Move the post support back over the holes.
What is the best way to install a fence post?
4:186:00How to Install Fence Posts | The Home Depot - YouTubeYouTubeStart of suggested clipEnd of suggested clipPosts can be set using concrete. Or compacted soil if setting metal vinyl or composite posts all theMorePosts can be set using concrete. Or compacted soil if setting metal vinyl or composite posts all the posts should be set in concrete. This will result in a sturdier fence.
Should metal fence posts be set in concrete?
You can install a chain link fence without using concrete, but it is not recommended. Anchoring each fence post in concrete is the best way to ensure your fence will stand straight and tall for many years.
How do you put a metal post in the ground without concrete?
Procedure:Find a concrete surface and lightly tamp your digging iron against it. ... Remove the turf and topsoil from the site of the post. ... Dig the hole putting the displaced earth onto the tarp. ... Pour 4 inches of gravel into the hole.Place the post in the hole. ... Add another 2 inches of gravel around the base of the post.More items...•
How do you secure fence posts?
1:493:42How to Install Fence Posts Step-by-step - YouTubeYouTubeStart of suggested clipEnd of suggested clipAttach a length of wood to the post and stakes to form a basic support brace holding the postMoreAttach a length of wood to the post and stakes to form a basic support brace holding the post upright while you position it straight use a level to ensure the fence post is perfectly vertical.
Are fence post anchors vs concrete?
Fences with posts set in anchor spikes are just as stable as fences with posts set in concrete. However, with concrete, your posts can and will rot over time as water seeps into the tiny gap caused by the wooden post expanding and contracting with the changes in temperature through the year.
How do you use post anchors?
2:393:47OZ-POST® WOOD POST ANCHORS - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust take your hammer and tap it closed. Finally you'll want to use a caulking gun to close up anyMoreJust take your hammer and tap it closed. Finally you'll want to use a caulking gun to close up any holes or open spaces to help prevent rot it really is the easiest way to anchor a post.
Should wood fence posts be set in concrete?
Concrete provides a strong foundation for wooden fence posts, but can rot them more quickly. Setting them in dirt, with or without gravel or crushed rock depending on your soil type, can help the posts last longer before going rotten. You can also use metal fence post anchors to prolong their life.
Is 2 feet deep enough for fence posts?
The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet).
How do you dig holes for fence posts?
In general, the post hole should be one third as deep as the fence is tall. So, if you're installing a 6-foot tall fence, your post hole should be at least two feet deep. You'll also want to be sure the bottom of the post sits below the frost line.
How do you make a wood fence with galvanized metal posts?
0:026:51Build A Fence That Will Last! (Wooden Fence With Metal Posts)YouTubeStart of suggested clipEnd of suggested clipAnd we dug the holes. And cemented them in so we used a post hole digger. And we dug these about twoMoreAnd we dug the holes. And cemented them in so we used a post hole digger. And we dug these about two feet deep so these are about two feet deep and then we filled them with cement.
How do you install green metal fence posts?
0:242:07How to Install T Posts - YouTubeYouTubeStart of suggested clipEnd of suggested clipPosition your T post with the anchor plate at the bottom and perpendicular to the fence line be sureMorePosition your T post with the anchor plate at the bottom and perpendicular to the fence line be sure to orient the post with the wire locating studs all facing the same direction.
How long do galvanized fence posts last?
50 -70 yearsIn some cases, galvanized steel fence posts can last 50 -70 years with little to no maintenance. The galvanized coating protects the steel underneath, as the elements must first destroy the zinc coating before compromising the strength of the metal.
How deep should a metal fence post be?
The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet). Add about 6 inches of QUIKRETE All-Purpose Gravel into the bottom of the hole.
What is an oz post?
Oz-Post™ represents both a change and advance in the concept of ground supports of a magnitude not seen for many years. Oz-Posts™ replace the traditional method of installing fence, signs, decks, and any other round or square posts. Oz-Posts™ are driven into the ground in minutes instead of spending hours digging holes and filling with concrete.
What size chisel holder for oz posts?
Driver for installing Oz-Posts fits most common jackhammers available for rent or sale (electric or gas jackhammers with 1-1/8" hex chisel holder w/retaining collar)
Can you use an Oz post as a temporary post?
As a result the Oz-Post™ can be used as both a permanent or temporary post installation system. Both on insertion and removal there is little or no environmental impact and wood posts are protected from rot caused by soil and moisture.
What is an oz post?
Oz-Posts are hot dipped galvanized and under normal conditions will outlast the expected service of the post that they support. Oz-Posts have a much thicker zinc coating than most common steel fence posts available on the market. Oz-Posts are also suitable for use with pressure treated lumber.
How strong are oz posts?
A fence or sign constructed as recommended using Oz-Posts will be equally as strong as traditional concrete installation. A post placed in a standard 6"- 8" post hole with one or two bags ...
What is an oz hammer?
Our exclusive Oz-Hammer is a high grade steel attachment that fits most common jackhammers. The Oz-Hammer transfers vibrating forces of the jackhammer to the Oz-Post. You may need to get a Hammer-Spacer to adapt the Oz-Hammer to the Oz-Post model that you are using. See our web site to determine which Oz-Posts require the Hammer-Spacer.
How long to tighten Oz Post?
It is recommended that the hardware be tightened 2-6 months after installation to assure the tightest possible connection. The use of a small amount of polyurethane glue is a great option to allow for a strong connection without the need to retighten the screws. Please review installation instructions for the model that you are installing for all installation options.
Can you drive a post back in the ground?
If for whatever reason a post installed with Oz-Posts is heaved out of alignment it can easily be driven back in the ground or removed and reinstalled in the correct location. The same operation with a concrete installation would prove to be very costly and time consuming.
Can you remove an Oz post?
Yes, Oz-Posts can be extracted if they are placed in the wrong spot, the fence needs moving, or they are only temporary. In lightly compacted soil conditions you can remove Oz-Post by using a 6' long pry bar. Place the pry bar under the housing, and using a piece of wood or a concrete building block placed at approximately 10" from the Oz-Post you can lever the Oz-Post out of the ground. If this fails your Oz-Post distributor can sell or rent you an Oz-Puller to make this process much easier.
Can oz post be used in cold weather?
Oz-Posts perform excellent in both warm and cold climates. Frost is a force that can easily ruin any kind of post installation that is not done correctly. In areas that experience below freezing conditions evidence of damage caused by frost is easy to spot and very common. The best and easiest solution for this problem is Oz-Post!
How long does it take to install an Oz post?
After the Oz-Post™ has been installed, its large fins "grab" the surrounding terrain, therefore, stabilizing the post. With an installation time of 1 minute, Oz-Post™ has taken the labor and guesswork out of installing posts!
What is an oz post?
The Oz-Post™ is a post anchor for use when erecting all types of fences, sign posts or decks. Application & Uses: The Oz-post™ is suitable for steel, wood and plastic posts. Many round, square, and rectangular cross sections can be accommodated.
What type of soil can you use for Oz Posts?
Oz-Posts™ can be driven into all kinds of soil conditions like rock, stone, asphalt, concrete, clay, compacted sand, and frozen ground. Once installed to a typical depth of 34”, the thick metal fins and heavy duty sleeve provide the same strength as a post installed in a 6”-8” post hole with concrete.
What happens when you remove Oz Post?
Removal of the Oz-Post™ leaves a small ''X'' in the ground which will disappear after the first rainfall. The extracted Oz-Post™ can be re-used repeatedly in many different locations.
Where is Oz Post tested?
These tests and approvals have been carried out independently by Government departments and the Department of Civil Engineering at the University of Queensland, which is a NATA accredited testing facility.
Is Oz Post removable?
While the Oz-Post™ is removable, it will save time and energy if the Oz-Post™ is positioned correctly. Local cities have various regulations regarding the placement of signs on public and private property.
Do you need concrete for oz posts?
No concrete is required and the large surface area of the fins gives maximum contact with the surrounding soil resulting in excellent grip and stability. The Oz-Post™ is suitable for most common post cross sections including round, square and rectangle.
Why are my posts crooked?
Crooked posts are caused by several factors like unstable soil, frost and shallow depth. This is especially noticeable in the south where most people/contractors do not dig deeper than 24”. The main reason that most post holes are dug is to enable you to get the post anchored deep in the ground.
Is there a place like Oz Post?
There is a place products like the oz-post, but I certainly would hate to lead someone into using them improperly or expecting more than they can deliver over a reasonable period of time in the real world.
Do thin posts work?
A thin post may work great when driven through asphalt into a strong compacted soil. This is the reason thin posts do not work in the ordinary world where gates swing, winds blow and the soil gets wet. This is also the reason DIY people still willing to spend some time (almost free) to install something that lasts instead of a paper-engineered product that costs more and does not perform in the typical situations.
