Installed on the existing fence:
- Such as welded wire mesh fence, chain link fence, expanded mesh fence, etc.
- Put a roll of razor wire at the top of the fence and fix its top and bottom at the beginning of the fence post.
- Stretch the razor wire roll to the other end of the fence post and fix the top and bottom on the fence post again.
How to install razor wire fence?
Razor wire fence can be mounted directly on the razor wire surface all the preparation and assembly quality and prompt implementation. Razor wire fence installation examples are here, three razor concertina coils as a fence, razor concertina wire installed on the wall or on the welded razor fence.
How do you measure the length of a razor wire?
To get the total length of the wire you need the following measurements: An example of razor wire showing three parallel (straight) wires. 1. Parallel wire length (PWL) which is the total length of wire placed horizontally above your fence.
What is an example of razor wire?
An example of razor wire showing three parallel (straight) wires. 1. Parallel wire length (PWL) which is the total length of wire placed horizontally above your fence. These are usually composed of three wires placed on parallel lines with at least a 1 foot distance from each other.
Can you use razor wire for Concertina wire?
Concertina wire can be installed on the ground or over an existing welded wire and razor wire fence. you can use razor wire barbed tape to create effective barriers for civil, military and special purpose. Razor wire concertina barrier installation steps in here.
What is razor wire?
What to use if fence is not barbwired?
How to stretch a coil?
How to break a snag in a fence?
Why use rebar ties?
How to avoid injury in a coil?
Where are materials installed in a fence?
See 2 more
How do you attach razor wire to a fence?
How we do the Concertina Razor Wire InstallationPlacement of the material. ... Spacing of the coil. ... Attachments. ... Along the fence line arrange the coils. ... Place the coil on its side and then remove the wire ties and discard them.Hold the coil steadily and place it along the length of the fencing line.More items...
Does razor wire go on the inside or outside of fence?
As a result the total wire length needed in your installation will be equal to the combined length of the PWL and CWL. Don't forget to use feet in all wire measurements. Razor wire braces are usually placed on top of each fence pole tilted 45 degrees toward the outside of your property.
Can you put razor wire on your fence?
The use of razor wire is not prohibited. There is no legal obligation in most countries regarding this issue. Therefore, it is legal to use razor wire and can be used in any area that requires security.
How much does it cost to install razor wire?
You can expect to pay between $1 and $3 per linear foot to install a razor wire fence. Fencing created using razor wire typically involves placing strands of razor wire across wooden or metal posts. Razor wire can also be affixed to the top of fences to provide added security.
Can you put razor wire around your property?
Barbed wire, razor wire and other such materials are not permitted in any residential zone except for security facilities around utility or communications facilities, or government facilities.
How effective is razor wire?
Razor wire is used in many security applications because, although it can be circumvented relatively quickly by humans with tools, penetrating a razor-wire barrier without tools is very slow and typically injurious, often thwarting such attempts or giving security forces more time to respond.
Can my Neighbour put up a fence without my permission?
If it's within their property boundary, your neighbour has every right to do whatever they want, including installing a fence.
What can I put on my fence to stop burglars?
High side and rear boundaries with trellis and spiky defensive planting; keep hedges, walls and fences around your back garden high (over 1.8 metres). Add lightweight trellis to gates and fences and plant some prickly plants to make it harder for burglars to climb over.
Should a fence be flush to the ground?
In most applications, a wood fence should be installed at least two inches off the ground. Your posts and rot boards (if you choose to install them) should be the only fence components that contact the ground. Wood pickets should never touch it.
What is the cheapest fence to install?
PVC fencing. The cheapest way to create a fence for your home is by getting one made from PVC. Such fences substitute wooden pickets and stakes to offer your protection from the outside world. PVC sleeves improve the stability of wooden posts used as a fence, reducing the cost of material and the labor used.
Is razor wire hard to cut?
The wire is exceedingly hard to cut utilizing hand devices. While the barbs have a penetrating and grasping activity, reinforced steel makes it difficult to twist.
How do you get around razor wire?
You can go over it. Some climb up, near a pole, or some put something over it, like a blanket, to help them cross over it without getting snagged. Another option is under. Hold the bottom wire, or two, up and slither under.
Which side does the wire go on a fence?
insideIf you have a bit of experience building fence, you know the proper answer to this question is the wire always goes on the inside of the fence so the livestock pressure has to push against both the post and wire if they want to stick their heads through the fence.
Which side of the fence should be facing in?
Face the finished side of the fence toward your neighbor The finished side should face toward your neighbor. Not only is this more polite, but it's the standard. Your property will look a lot nicer with the “good” side facing the outside world. Otherwise, your fence will look like it was installed backward.
Which side of a fence or outside?
This is a very common question. Many (but not all!) fences have two distinct sides: a finished side and a side where the structural components are more apparent. The finished side should face out, and the structural side should face into your yard.
Can you put razor wire on the ground?
Anchor the beginning coil of razor wire to an end fence post by using aluminum tie wraps to strap the wire to the fence post and stake the wire into the ground securely with a forked stake. If you do not have access to a fence post, place an aluminum post in the ground to make an anchor post for the wire.
How many people should be on a razor wire installation?
A team of three to five would be advisable to handle this job. While installing your razor wire, don’t forget to ensure your safety and the safety of those people working with you. Proper tools, protective gear and secured ladders should be used.
How to install 3 parallel wires?
You will need to install the parallel wires first. To do this, take one end of your razor wire and attach it securely to a corner post brace. Stretch your wire on a straight line and tie it to each brace until the entire perimeter is covered. Do this two more times in order to complete the three-parallel-wire installation.
What is coiling wire length?
2. Coiling wire length (CWL) which is the total length of the wire placed on the parallel wires. Use this only if you chose to install the said coiling wires for added security. Compute for the wire length as follows:
Why is razor wire used on chain link fences?
Razor wire provides the ultimate in security and safety for your property. When criminals see a fence topped with razor wire, they’ll think twice about trying to get into your property. Razor wire makes chain link fences virtually unclimbable; people will move on to easier targets when they see your razor wire.
What is PWL wire?
1. Parallel wire length (PWL) which is the total length of wire placed horizontally above your fence . These are usually composed of three wires placed on parallel lines with at least a 1 foot distance from each other. To compute the total wire length for this, use the following formula:
Can razor wire be sever?
Our biggest advice: be careful! Razor wire can cause sever injuries if you’re not careful, and needs to be handled accordingly.
How far can razor wire be from a fence?
Determine the number of rolls used in each stage or section of fencing,, this depends on the type of razor wire is elected, as each roll can reach from 8 to 15 feet away, is an item must consider very important.
How often should you distribute razor wire?
Once at this point, distribute the razor wire every 25 cm, , once a roll has come to an end, you must hold the tail end of the first roll with the point of beginning of the second, so that there is no space of perimeter uncovered, this is important, because it can be an easy point of exceeding our fence and our installation will not be helped.
Where are razor wires made?
Our razor wire products are made in the United States – NOT in China — and they exceed Federal and state industrial specifications for quality. The enclosed spring steel core makes them harder to cut or bend, bringing unrivaled security to properties like equipment yards, construction sites, and military installations.
When pulling concertina wire along a fence line, should there be another installer?
When we are pulling the concertina wire along the fence line, there should be another installer to assure the coil spacing consistency by pulling and lifting the materials.
How to measure coil spacing?
Measure the space between one clip and the adjoining one. This determines the spacing between the coils. Usually a spacing of 12” is done with a plus or minus of 2 inches variance. Hence consistency is the key.
What is double concertina wire made of?
Double concertina wires are made with two pieces of stainless steel razor wire or with zinc coated razor wire; which are bound together for more strength.
What type of gloves do you suggest to be worn when working with the concertina wire?
The wire safety gloves consist of several calf leather layers and a brass mesh layer in it.
Can razor wire fence be mounted directly on razor wire?
Razor wire fence can be mounted directly on the razor wire surface all the preparation and assembly quality and prompt implementation.
Can concertina wire be used over razor wire?
The use of concertina wire barriers can enhance security. Concertina wire can be installed on the ground or over an existing welded wire and razor wire fence. Read More.
Can you use razor wire barbed tape?
you can use razor wire barbed tape to create effective barriers for civil, military and special purpose. Razor wire concertina barrier installation steps in here.
What is razor wire?
Razor wire is a generic term for barbed tape. There are several forms of razor wire. The most common is known as concertina wire. Concertina wire uses a stainless steel tape wrapped around a core wire. Each complete coil is clipped to the adjoining coil. When stretched, this creates a spring-like effect.
What to use if fence is not barbwired?
If not fence or barbwire, use ground stakes.
How to stretch a coil?
With the coil on its side, remove the wire ties and discard. Firmly hold the coil and place along the fence line where you are to begin the stretch. If you do not firmly hold the coil, it will spring loose. Allow approximately six coils to naturally spring free from the spool closest to the starting point.
How to break a snag in a fence?
While pulling the materials along the fence line, gently shake it to break free any snags between coils. It is not uncommon that one barb gets entangled with another. These can be separated by firmly grasping the two coils and pulling the barbs apart and away. However, make sure that no one else is moving the materials while you correct this snag.
Why use rebar ties?
The rebar ties are used to reduce vibrations but take considerably longer to install. Once you know the location and attachment of the materials, you may begin to install. Layout your coils along the fence line. You will need to know how much deployment per coil.
How to avoid injury in a coil?
No loose clothing and long sleeves. To prevent injury, use a slow fluid like motion to grab the materials. With your eyes fixed to your hands and arms, carefully navigate your hands to the materials. When reaching inside of the coils, carefully and slowly navigate your arms in and out of the coil.
Where are materials installed in a fence?
Material placement. The materials may be installed on the ground, on top of an adjoining role, a pyramid, against the fence and on top of the fence. Each installation poses it own unique challenges.
Placement of The Material
Spacing of The Coil
- Measure the space between one clip and the adjoining one. This determines the spacing between the coils. Usually a spacing of 12” is done with a plus or minus of 2 inches variance. Hence consistency is the key.
Attachments
- Usually concertina wire is attached every four feet to the adjoining role and on every foot to the fence. It can be attached with stainless steel rebar ties or with hog rings. Rebar ties generally reduce any vibrations but it does take a little longer to install. Now, let’s talk about the installation process-
Step 1
- Along the fence line arrange the coils. The deployment for each coil needs to be decided. This would depend on the spacing of the coil and the number of coils per roll.
Step 3
- Hold the coil steadily and place it along the length of the fencing line. This is where we begin stretching.
Step 4
- Use around six coils and allow them to spring free from the spool which is closest to the starting point. Then these are to be attached to the fence keeping centers of approximately 6 inches.
Step 5
- Once the spool has been anchored, take three coils on the other end of the spool. Grasp all three firmly and spread these about one foot from the spool.
Step 6
- Grasping all the three spools start stretching the wire. We maintain a distance from the fence as well as the concertina wire to avoid any kind of snags.
Step 7
- During the pulling process, shake it gently so as to free any snags between any of the coils. It does happen that barb can get entangled. If it happens, then separate by grasping firmly and spreading them apart. But while we are correcting this, we make sure that there is no one else moving the materials.
Step 8
- When we are pulling the concertina wire along the fence line, there should be another installer to assure the coil spacing consistency by pulling and lifting the materials.