- Determine How Much Soffit You Will Need. Measure and calculate the total square footage needed for the areas requiring soffit. ...
- Prep the Area. Check surfaces to make sure they are uniform and straight. Reattach any loose boards or shingles that might affect your installation procedure.
- Install Soffit. Insert the soffit panel into the channel. Make sure the panel forms a 90-degree angle with the wall.
- Finish the Installation. Once all panels have been installed, apply utility trim and fasten using trim nails. ...
How do you install soffits on fascia board?
Determine the preferred method of installing soffit at the fascia board. When installing J-channel at either wall of fascia board, nail every 8” to 12” (203mm to 305mm). If the soffit is to turn a corner, cut and install J-channel to allow 1/4” (6.4mm) for expansion at each of the adjoining walls and fascia boards.
How do you install an open eave vinyl soffit?
Open eave installation of a vinyl soffit begins by first installing the proper receiving channels. Either F-channel or J-channel can be used. J-channel can be modified to create F-channel. Simply cut slots in the nail flange area where it would be nailed to the wall.
How do you nail a soffit panel?
The panel is held in place with small-headed nails driven into the fascia board or nailing strip. If nailing into the fascia board, drive the nail through the nail flange and the “V” groove. This is one of the few times when face nailing of the soffit material is permissible.
How do you expand a soffit?
If the soffit is to turn a corner, cut and install J-channel to allow 1/4” (6.4mm) for expansion at each of the adjoining walls and fascia boards. When installing vented soffit panels, if the existing soffit doesn’t have openings for ventilation, cut an adequate number of openings.
What is the procedure used to install soffit?
How much expansion is needed for a corner soffit?
What is soffit used for?
What is a vinyl soffit?
When transitioning soffit at the peak of a gable (Fig. 63), what is?
Where do you drive nails in a soffit?
Can a soffit panel be fastened to a nailing strip?
See 2 more
How do you install soffit and fascia trim?
24:5029:57How To Install Soffit And Fascia - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're going to take a trim nail. And instead of nailing the face of it this time we're going to nailMoreWe're going to take a trim nail. And instead of nailing the face of it this time we're going to nail. It. Up under into the groove of the soffit. So we'll go ahead and get a nail started here.
How do you install soffit starter trim?
1:596:55How To Install Soffit and Fascia Trim - YouTubeYouTubeStart of suggested clipEnd of suggested clipPiece size we're putting up I'm taking this piece here I've taken the piece that locks in just likeMorePiece size we're putting up I'm taking this piece here I've taken the piece that locks in just like the siding. I'm walking it in pushing. All the way over bringing. It back just a little bit.
How do you secure soffit?
Install SoffitInsert the soffit panel into the channel.Make sure the panel forms a 90-degree angle with the wall.Nail up the panel.Repeat these steps for each panel.Be sure the tongues and grooves of each panel line up with the panels alongside them.
Do you use nails or screws for soffit?
What nails to use for wood soffit? Galvanized, aluminum or stainless-steel nails are the best nails you can use for outdoor constructions like the wood soffit. Also, those nails can use for any kind of outdoor construction, installation, and repairing stuff as well.
What goes on first soffit or fascia?
Since the soffits are installed under the fascia boards, they should come first. It makes work more manageable for the constructor because they can see where to nail or adjust. Once the roofer has installed the soffits, they can install the fascia.
How are soffits attached?
On narrow eaves the rafter ends serve to fasten the soffit and fascia. A ledger plate is fastened to the wall to attach the soffit at that location. Wide eaves require additional nailing supports running from the rafter-ends/fascia board and back to the house wall. These are called lookouts.
How do you start a soffit?
1:211:49Soffit Installation - Renovation Tips - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd zinc alloy called prima loam steel insert a soffit piece inside the J shaped molding nail it toMoreAnd zinc alloy called prima loam steel insert a soffit piece inside the J shaped molding nail it to the inferior. Part of the fascia. Board. Always start at the extremity of the house.
Does soffit need to be vented?
Soffit can be non-vented or vented to allow for maximum roof ventilation. Non-vented or continuous soffit works best when your roof has narrow eaves or if you need to ventilate a large amount of attic space.
How do you attach wood soffit to fascia?
1:105:03Replacing Rotten Fascia & Soffits in Williston, Vermont - YouTubeYouTubeStart of suggested clipEnd of suggested clipBoard into the butt end of the trusses. I'm just moving it back maybe where you need it. I take aMoreBoard into the butt end of the trusses. I'm just moving it back maybe where you need it. I take a core right there Dustin go ahead and put a screw in. It. Those are two and a half.
Where do you screw soffits?
0:3414:25How To Install Soffit And Fascia - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo soffit is the panel that goes underneath your Eve of your house and the fascia is the l-shapedMoreSo soffit is the panel that goes underneath your Eve of your house and the fascia is the l-shaped panel that goes you know along where your Eve trough is on the on the vertical edge.
What kind of screws do you use for soffit?
Each soffit vent should have between 8 and 10 holes drilled along the outer edges for screws to go. We recommend ½ inch stainless steel sheet metal screws for each vent.
What nails should I use for soffit?
least 2” roofing nails (or 16d exterior trim nails.) Use 1 ½” roofing nails to install soffit. Use white panel nails to install aluminum fascia. Use tin snips to cut F-channel, vinyl soffit, and aluminum fascia.
How do you start a soffit?
1:211:49Soffit Installation - Renovation Tips - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd zinc alloy called prima loam steel insert a soffit piece inside the J shaped molding nail it toMoreAnd zinc alloy called prima loam steel insert a soffit piece inside the J shaped molding nail it to the inferior. Part of the fascia. Board. Always start at the extremity of the house.
Do you use J channel for soffit?
J-channel has traditionally been used as trim around windows and doors during vinyl and aluminum siding installations, along with being used quite frequently for soffit.
How do you install plastic soffit?
2:103:09How to Install Vinyl Soffits - YouTubeYouTubeStart of suggested clipEnd of suggested clipDirection or a vinyl siding blade to cut soffit panels insert the panel into the receiving. ChannelMoreDirection or a vinyl siding blade to cut soffit panels insert the panel into the receiving. Channel while checking that the panel is square then nail the other end into the fascia.
How do you install trim coil fascia?
0:132:06How to Install Aluminum Fascia Covers Including Bird BoxesYouTubeStart of suggested clipEnd of suggested clipYou can snap lock lugs onto the fascia panels to install aluminum fascia pre-drill nail holes aMoreYou can snap lock lugs onto the fascia panels to install aluminum fascia pre-drill nail holes a maximum of every 24 inches aligned with the v-shaped groove in the soffit.
What is the procedure used to install soffit?
The procedure used to install soffit depends on the construction of the eave. There are two different types of eaves: Open eaves—eaves with exposed rafters or trusses—are typical of new construction. Open eave installation procedures are also used when removing damaged soffit during a re-siding project. Enclosed eaves—eaves with soffit in place are ...
How much expansion is needed for a corner soffit?
If the soffit will turn a corner, cut and install the channel so there is 1/4” (6.4mm) for expansion at each of the adjoining walls.
What is soffit used for?
Soffit is used to enclose the underside of an eave. The installation of soffit will determine the positioning of the inside and outside corner posts. It also is necessary to complete the soffit before the final course of siding is installed on the wall. Vinyl soffit is designed to be easily installed lengthwise from wall to fascia.
What is a vinyl soffit?
Vinyl soffit is designed to be easily installed lengthwise from wall to fascia. Soffit panels are similar to vertical siding. Manufacturers produce both solid and vented panels, as well as combinations of the two. NOTE: Ventilation Requirements: Proper attic ventilation is important for any home.
When transitioning soffit at the peak of a gable (Fig. 63), what is?
When transitioning soffit at the peak of a gable (Fig. 63), secure two J-channels back to back to receive an individual piece of soffit on each accessory. Alternatively, bend a section of soffit, using a field brake, to match the angle of the peak of the gable.
Where do you drive nails in a soffit?
Drive these nails through the fascia and only into the “V” groove of the soffit.
Can a soffit panel be fastened to a nailing strip?
NOTE: According to the 2012 and later International Residential Codes, “Soffit panels shall be individually fastened to a supporting component such as a nailing strip, fascia, or subfascia component or as specified by the manufacturer’s instructions.”
How wide of a gap should a soffit be?
When the soffit turns a corner, the channel then needs to be installed with a 1/4-inch gap that can allow for expansion at the walls. Do not overdrive fasteners.
What is soffit siding?
Juan Rodriguez. Updated November 20, 2019. Soffit is comparable to vertical siding, and its installation entails more than the actual panels. It protects the underside of eaves and porch ceilings and can provide a hidden vent system.
How many square feet are there in a 12 foot soffit?
Measure and calculate the total square footage needed for the areas requiring soffit. Panels come in 12-foot lengths that are either 12 or 16 inches wide. Therefore, a panel that is 12 inches wide equates to 12 square feet, and a panel that is 16 inches wide equates to 16 square feet. Plan on purchasing enough soffit to cover about 5 percent more space than necessary to account for waste and overlaps.
How to measure fascia?
Measure from the wall to the fascia and subtract half an inch to allow for movement.
How to cut soffit panels?
Cutting dozens of soffit panels with a pair of snips is tiring and crushes the grooves together. A circular saw makes clean, precise cuts easy—when it's coupled with a cutting table. You can make a plywood-cutting table (Fig. B) in about an hour. The 45-degree side of the table is for cutting miters on hip roof soffits (see “How to Handle Soffit Corners on Hip Roofs.”).
What to do if your electrical line is near a soffit?
Call the power company for help with electrical lines that are near or pass through soffits or fascias.
What is a trim nail punch?
Trim nail punch for holding and setting nails into soffit grooves and tight places. Combination square for making clean fascia bends to go around corners.
What is the best material to use for soffits?
Aluminum is a good solution for wood soffits and fascias in awful shape. It’ll take less time to bury them behind aluminum trim than to repair, scrape and repaint the old wood.
How to calculate square footage of soffit?
To calculate quantity, multiply width by length (in feet) of each soffit surface, add them all up to get total square footage and divide by 16 (the square footage of one 16-in. panel). Add 5 percent extra for waste and overlaps.
How wide is a wood fascia?
It comes in two standard widths: 6 and 8 in. Measure the width of your wood fascia to determine which width to buy.
How to cut aluminum with a plywood saw?
Use a plywood crosscutting blade mounted backward —the saw teeth point down in a clockwise direction. Before reversing the blade, make a pass halfway through the top of the plywood saw table to create a saw blade groove. This allows the blade to cut completely and cleanly through the aluminum. For multiple cuts of the same length, clamp a stop block to the table fence. Cut panels 1/4 in. short of the measured width. Caution: Wear hearing and eye protection.
How do I cut aluminum soffit?
Working with factory-finished aluminum soffit and fascia involves cutting operations that use a combination of hand and power tools. Besides a good pair of aviation snips for medium-sized cuts, I use a pair of small, first-aid scissors for completing tiny cuts accurately. And you can’t beat a sliding compound mitre saw for large, repetitive cuts. The blade I prefer is made especially for soffit and fascia work, and slices more cleanly and quietly than a regular crosscut blade. For best results, also give a quick shot of WD-40 to the teeth after every few cuts, to extend blade life.
Where is the soffit on a chopsaw?
Aluminum soffit upside down and in place on the outfeed table of a chopsaw. Note the felt on the table protecting the painted surface.
What is the best nail for soffit?
Soffit and fascia installed and ready to last a long time. Stainless steel nails hold much better than the traditional aluminum nails used for this application.
What is the vertical edge of a roof?
Fascia is the vertical edge of a roof, and factory-finished aluminum fascia is an excellent option for this situation.
Why is fascia secured?
Securing fascia so it withstands every kind of harsh weather that comes along.
What is the procedure used to install soffit?
The procedure used to install soffit depends on the construction of the eave. There are two different types of eaves: Open eaves—eaves with exposed rafters or trusses—are typical of new construction. Open eave installation procedures are also used when removing damaged soffit during a re-siding project. Enclosed eaves—eaves with soffit in place are ...
How much expansion is needed for a corner soffit?
If the soffit will turn a corner, cut and install the channel so there is 1/4” (6.4mm) for expansion at each of the adjoining walls.
What is soffit used for?
Soffit is used to enclose the underside of an eave. The installation of soffit will determine the positioning of the inside and outside corner posts. It also is necessary to complete the soffit before the final course of siding is installed on the wall. Vinyl soffit is designed to be easily installed lengthwise from wall to fascia.
What is a vinyl soffit?
Vinyl soffit is designed to be easily installed lengthwise from wall to fascia. Soffit panels are similar to vertical siding. Manufacturers produce both solid and vented panels, as well as combinations of the two. NOTE: Ventilation Requirements: Proper attic ventilation is important for any home.
When transitioning soffit at the peak of a gable (Fig. 63), what is?
When transitioning soffit at the peak of a gable (Fig. 63), secure two J-channels back to back to receive an individual piece of soffit on each accessory. Alternatively, bend a section of soffit, using a field brake, to match the angle of the peak of the gable.
Where do you drive nails in a soffit?
Drive these nails through the fascia and only into the “V” groove of the soffit.
Can a soffit panel be fastened to a nailing strip?
NOTE: According to the 2012 and later International Residential Codes, “Soffit panels shall be individually fastened to a supporting component such as a nailing strip, fascia, or subfascia component or as specified by the manufacturer’s instructions.”