6-step process to install your standing seam metal roof
- 1. Tear off your old roof ...
- 2. Install lock strips at the rakes and eaves ...
- 3. Put down high heat ice and water shield ...
- 4. Install your standing seam metal panels ...
- 5. Fill in the gap between the standing seam metal panels and the top of your roof ...
- 6. Lock the ridge capping into the Z bar ...
How do you install a standing seam metal roof?
Standing Seam Metal Roof Installation Process 1 Step 1 – Installing the drip edge. ... 2 Step 2 – Gable / Rake trim: With standing seam metal, there are at least two ways to trim the gables of your roof with many variations; using a special ... 3 Step 3 – Installing your first panel. ... 4 Step 3.1 – flashing a vent (stink) pipe. ...
How do you fasten a standing seam to the wall?
Fasten with appropriate substrate fastener at minimum 4 fasteners per zee or 12 inches on center. Standing Seam - Architectural Install Guide Page 18 of 38 ○ Install sidewall flashing by pop riveting sidewall flashing to top flange of zee closure at 18 inches on center and positioning vertical face against wall.
How do you install metal siding on a vertical wall?
To install vertical metal siding, start by applying horizontal furring strips and sheathing to the surface you're working on if it's uneven. Then, install the corner posts that came with your siding and nail j-channel along the top and bottom of the wall.
How do you install roof panels on a house?
Installation of Panels. Roof Panels. We require at least a 3 / 12 pitch for standing seam panels, to ensure proper water drainage. This means that the minimum roof slope required for panels is 3 inches of rise per foot.
What is a standing seam roof?
What are the different types of standing seam panels?
Why is standing seam roofing more expensive?
What does it mean when someone thinks of standing seams?
How much does it cost to install siding?
Is Western States Metal Roofing a manufacturer?
Do you need to install standing seam panels vertically?
See 2 more
Can you use standing seam metal for siding?
Standing seam is a popular metal roofing product suitable for both residential and commercial applications. It also serves as an attractive and versatile siding solution. Standing seam offers superior performance, a clean appearance, and can be installed on most building types.
How is standing seam installed?
6-step process to install your standing seam metal roofTear off your old roof. ... Install lock strips at the rakes and eaves. ... Put down high heat ice and water shield. ... Install your standing seam metal panels. ... Fill in the gap between the standing seam metal panels and the top of your roof. ... Lock the ridge capping into the Z bar.
What's the proper way to install rib steel siding?
3:256:05Max-Rib Installation | McElroy Metal - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure that you place the fastener either through the tape sealant and inside closure or as closeMoreMake sure that you place the fastener either through the tape sealant and inside closure or as close to the uphill edge as you can do not place fasteners below the line of tape. Enclosures.
Do you need underlayment for metal siding?
Metal siding requires an underlayment to protect against weather conditions and form a tight seal. Breathable, synthetic material is preferable. This can allow moisture to escape without allowing it in, which will help preserve the undersurface. This can be attached using a staple gun.
Can standing seam be put over shingles?
Clip alignment is key to a proper installation of a standing seam recover over shingles. The clips have eight holes so the installer can align the fasteners through the ends of the shingle tabs. The clip also will work on dimensional or architectural shingled roofs as well.
How do you attach a metal roof to the side of a house?
3:134:52Endwall Flashing Installation On A Metal Roof. EASY ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe top section should slide inwards onto the lower section of notched end wall fastening and wallMoreThe top section should slide inwards onto the lower section of notched end wall fastening and wall pancake screws should be used to fasten the top section of the end wall one inch from the edge.
How far apart do you screw metal siding?
⅞” Corrugated Screw Location For Wall Panels Or Metal Siding Lap screws are spaced 12” to 18” on center. The panel screws are spaced out so that every third corrugation has a screw including both sides of the panel sidelap.
Where do screws go in metal siding?
0:062:50Screw Location Recommendations - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe screws go in the flat of the panel. And not on top of the rib. Some of our competitors. TheirMoreThe screws go in the flat of the panel. And not on top of the rib. Some of our competitors. Their recommendations are to go on top of the rib.
Do you have to put plywood under metal roof?
Although it may seem counterintuitive, metal roofing can be attached directly to your building's roofing structure without the need and expense of plywood sheeting.
Do you need Tyvek under metal siding?
Tyvek or other similar modern building is needed for insulated walls with poor circulation, metal or no metal. Metal also traps moisture and stops airflow in both directions so keeping the condensed moisture off the sheathing is important to prevent it from rotting.
Can you put metal siding over plywood?
Metal roofing should not be installed directly over the top of bare plywood. You do not have to install roofing shingles or other roofing material, but a felt sheet over the plywood is the bare minimum.
How do you install metal siding on a house?
InstructionsPrepare the Site. In most cases, any existing siding will need to be removed prior to new siding installation. ... Install Drip Cap at Doors and Windows. ... Install House Wrap. ... Seal House Wrap. ... Install Bottom Trim. ... Install J-channel Around Doors and Windows. ... Install Siding. ... Install Corners.More items...•
How much does it cost to install a standing seam metal roof?
between $24,000 to $42,000The average cost to install a standing seam metal roof is anywhere between $24,000 to $42,000 depending on the slope, pitch, and size of your roof. You can expect to pay $8 to $14 per square foot, or $800 to $1,400 per square, installed on a standard sized single story home.
Can you walk on standing seam metal roof?
Standing Seam Metal Roofs – can be easily walked on without damage, but they are steep and slippery. Safety equipment use is a necessity. Corrugated Steel Roofs – are also easily walked on without damage as their installation is done directly to the roof decking.
Is a standing seam roof worth it?
Thanks to hidden fasteners and durable metal material, standing seam metal roofs are one of the best roofing options when it comes to durability and longevity.
How do you seam a standing seam metal roof?
2:514:24How To Install Standing Seam Metal Roofing - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe flat stock is fastened using pancake screws two inches apart around the perimeter. Next weMoreThe flat stock is fastened using pancake screws two inches apart around the perimeter. Next we sealed the flat stock with a four foot by four foot piece of shark skin self-adhesive underlayment prior
What is a standing seam roof?
Standing seam roofs are known in the steel roofing industry as being the premium metal roof. This is another way of saying “more expensive”. The same is true when it comes to siding.
What are the different types of standing seam panels?
There are three types of standing seam panel systems: mechanically seamed, snap lock, and nail strip. However, not all of these are right for siding applications.
Why is standing seam roofing more expensive?
A standing seam roofing system costs more because it's an overall higher quality roof.
What does it mean when someone thinks of standing seams?
When someone thinks of standing seam, a picture of the bold, clean lines that makes standing seam so attractive most likely comes to mind. However, that mental picture is most likely up on a roof.
How much does it cost to install siding?
The cost of standing seam siding for materials is $2 to $4 per square foot. The cost to install the siding generally runs between $6 to $8 per square foot.
Is Western States Metal Roofing a manufacturer?
This is a question we’ve been hearing more often at Western States Metal Roofing lately. As a manufacturer of metal roofing and siding panels, we work with customers that are interested in using metal panels for both applications.
Do you need to install standing seam panels vertically?
Standing seam panels need to be installed vertically when used as siding. The laps on the panels are not set up for horizontal installation.
What is the most important thing about standing seam roofing?
The most important thing about installing standing seam, is to measure the roof correctly and precisely. Here is why; Each standing seam panel is cut to the exact size, and if your panels are too short, you will run the following costly issues: A) If a panel is only 2″ short, you may not be able to use your ridge cap as it will not cover ...
What size nails should I use for a roof deck?
Nails: We use 1 1/2″ plastic cap nails to attach the underlayment to the roof deck. They are rust-proof, lightweight and will not damage the underlayment, unlike regular roofing nails. You can buy a large bucket of these nails at Home Depot or Lowe’s, but I recommend not to get 1-inch nails, which the above-mentioned stores usually stock. Get the longer ones, and it will be much easier for you to work with them.
Why do you need a drip edge after a roof?
Advantages of installing drip edge after the roofing underlayment has been installed, are as follows: You do not waste any precious time during the installation of the drip edge; when and if your roof is open and it rains, you may not have enough time to cover it, that’s where having water and vapor barrier in place really comes handy. Second reason is the safety.
What can you make with a hand seamer?
With the hand seamer / folder, you can make such complex flashing pieces as chimney collar, sidewall, etc. You will find it very useful and essential to the installation of a metal roof. The above-mentioned tools are the bare essentials you’ll need to install any metal roof, whether metal shingles or standing seam.
How long can you leave a roof underlayment on?
You can easily walk on the underlayment, after securely attaching it to the roof deck, and you can leave it exposed up-to 6 months and not worry about leaks. Nails: We use 1 1/2″ plastic cap nails to attach the underlayment to the roof deck.
What is the best caulking for a roof?
Sealant / Caulking: Each roofer has his/her own preference when it comes to sealants, and my love goes to Solar Seal 900. I found it to be the best caulking that is water-tight, cures fast, has very strong adhesion, is rather inexpensive and comes in a variety of colors.
What tools do I need to pull nails out of a roof?
Necessary Tools, Materials, and Supplies. A roofing hatchet or a carpenter’s hammer. I prefer a hatchet, but in some cases you do need a claw-hammer of some type to pull out nails. You can also use a flat bar, but it’s not always convenient to have too many bulky things on the roof.
What does metal siding look like?
Metal siding looks best when it's installed on a flat, level surface. If the surface you're working on is uneven, the metal siding will look wavy and distorted. Check the wall beforehand so you know whether or not you'll need to level it out before you get started.
How to install furring strips?
To install the furring strips, start by cutting them to size so they run from one end of the surface to the other. Then, nail them to the surface you're working on, leaving 16 inches (41 cm) between each strip. Make sure you install the furring strips horizontally and not vertically.
How to secure a panel?
Hammer nails into the nail slots every 16 inches (41 cm) down the panel. Once one edge of the panel is locked into place , you'll need to nail the other edge to the sheathing to secure the panel. Make sure you hammer a nail into the top and bottom nail slots on the panel. ...
How to cut a panel around a window?
If you need to panel around any windows or doors, start by holding the panel over the section of the window or door you're working with . Then, measure and mark where you need to cut out space for the frame on the panel.
How thick should sheathing be?
Choose sheathing that's no more than 1 inch (2.5 cm) thick so you're not building too far out from the wall.
Is vertical siding the same as horizontal siding?
Vertical metal siding can give a building a modern, sleek appearance. While installing vertical metal siding is similar to installing horizontal siding, there are a few differences you'll want to keep in mind. Fortunately, with the right tools and preparation, putting vertical metal siding up on a building can be a smooth and simple process.
Can you put metal siding on a wall?
Skip furring strips and sheathing if you're working with an even surface. Sometimes it's not necessary to even out the surface you're working on, especially if you're installing siding over a relatively new building. If that's the case, you can put the metal siding up on the wall as is.
How To Layout Metal Roofing Panels
When laying out your panels, you must plan the number of panels you will need to cover the width of your roof. For example if you are installing an 18” panel and your roof is 182” wide, you will have a small two inch gap.
How To Layout Pipe Penetrations
Pipes and other penetrations will also factor into your layout. You don't want the seam of a panel to land where a penetration is located. If there’s a pipe in the panel seam, you will need to adjust the sizes of the first and last panels to compensate for the adjustment.
How To Prepare Your Roof for Installation
Before you install your panels, always clear your roof of any dust or debris. Check your roof for any protrusions. You can often find raised screws, nails, or leftover scrap in the underlayment. Remove these since they can damage your standing seam panels.
Need More Help With Standing Seam Metal Roofing Installation?
For panels and accessories needed for your standing seam installation, go to the Western States Metal Roofing website to see our catalog, and request a quote or metal color sample as there are hundreds of colors to choose from.
What is the purpose of sealant on metal roofing?
c. Sealants: Sealant is a necessary component to prevent water from infiltrating thru the metal roofing system. It is applied to joints, laps, intersections, and perimeter edges of panels and flashings. It is also applied to laps and joints of gutters and downspouts to control water containment to ground level.
What to wear when cutting and drilling?
Wear heavy gloves for protection. ○ Wear eye protection when cutting and drilling to prevent eye injury from flying metal fragments. ○ Take caution when handling panels and trim in strong winds. Wind pressure can cause loss of balance and endanger workers with being struck by flying objects.
How high is a standing seam?
Standing Seam features approximately one-inch high ribs and a net coverage of 16 inches. The “nail strip” and screws that attach each panel are in turn covered by each subsequent panel as each overlapping panel locks into place over the previous one.
What is sidewall installation?
Sidewall installation is similar to that of gable trim. As with the gable, one option is attaching the sidewall with a Z-flashing installed over the roof panel. We recommend the step sidewall that mounts directly to the roof with trim screws.
What is flashing on a roof?
The most common flashing for standing seam roofing is the ridge cap, which is used at the peak of a roof where two opposing roof slopes join, and attaches to the roof with z-flashing. Other flashings include gable trim, which runs up the sloped ends of the roof, and drip edge or eave trim, which trims out the lower ends of the panels and provides a surface for the attachment of the lower end of the panel. Both gable and drip edge are often applied above the fascia trim, and are attached with surface screws. For details about the application of each type trim see the details on pgs. 10-15.
What is a standing seam roof?
Standing seam roofs are known in the steel roofing industry as being the premium metal roof. This is another way of saying “more expensive”. The same is true when it comes to siding.
What are the different types of standing seam panels?
There are three types of standing seam panel systems: mechanically seamed, snap lock, and nail strip. However, not all of these are right for siding applications.
Why is standing seam roofing more expensive?
A standing seam roofing system costs more because it's an overall higher quality roof.
What does it mean when someone thinks of standing seams?
When someone thinks of standing seam, a picture of the bold, clean lines that makes standing seam so attractive most likely comes to mind. However, that mental picture is most likely up on a roof.
How much does it cost to install siding?
The cost of standing seam siding for materials is $2 to $4 per square foot. The cost to install the siding generally runs between $6 to $8 per square foot.
Is Western States Metal Roofing a manufacturer?
This is a question we’ve been hearing more often at Western States Metal Roofing lately. As a manufacturer of metal roofing and siding panels, we work with customers that are interested in using metal panels for both applications.
Do you need to install standing seam panels vertically?
Standing seam panels need to be installed vertically when used as siding. The laps on the panels are not set up for horizontal installation.
