7 Steps to Installing Under Cabinet Kitchen Lighting with LED Light Strips
- Prepare Your Area and Understand Your Layout. I knew going into this project that I would have two “sections” of LED lighting. ...
- Understand How All of the LED Components Connect Together. ...
- Drill Necessary Holes. ...
- Cut Mounting Channels to Length. ...
- Cut and Connect LED Light Strips to Install Under Cabinet Lighting. ...
How do you install LED strip lights?
How to Install LED Strip Lights?
- Dry and clean the surface Before adhering any strip lights, clean the surface of the area you will be placing the lights on. ...
- Unroll the light strip, stick to the surface The LED strip lights come rolled on a spool. ...
- Connect LED light strip and turn on the light
How to install undercabinet LED lighting?
Step-by-Step Guide for Installing LED Lights Under The Cabinet
- Flip off the circuit breaker that powers the outlets in your kitchen. ...
- Remove the outlet where you plan to hardwire your under-cabinet lights. ...
- Drill a hole above the box through the cabinet’s bottom lip. ...
- Slide the cable lock connector upward several inches on the cable and snap it into place in the knockout at the top of your junction box.
What is the best wireless under cabinet lighting?
- BEST OVERALL: Litever Under Cabinet LED Lighting Kit
- RUNNER-UP: Lightkiwi E7574 Dimmable Under Cabinet Lighting Kit
- BEST BANG FOR THE BUCK: Lighting EVER LE LED Under Cabinet Puck Lights Kit
- HARDWIRED PICK: HARRRRD Hardwired LED Under Cabinet Task Lighting
- WIRELESS PICK: BLS T01L LED Closet Light
- LED PICK: Wobane Under Cabinet Flexible LED Strip Lights
How to install under cabinet lighting in your kitchen (DIY)?
Wire the Lights
- Splice wires with the leads inside the light, black to black and white to white.
- Position the wires flat in the base so they will not get in the way when you add the fixture body.
- Gently push the bottom portion of the light into position. If it does not go in easily, take it down and realign the wires for an easier fit.
- Attach the fixture base.
Where should light strips be placed under cabinets?
If you want to install under cabinet lighting as task lighting, you should place the strip lights closer to the middle front edge of the cabinets, so the countertop will be exposed to as much light as possible. For ambient or accent lighting, you may want to place them closer to the back edge.
How do you stick lights under cabinets?
1:472:54How to Install Under Cabinet Lighting - YouTubeYouTubeStart of suggested clipEnd of suggested clipSimply fasten with the included clips and plug in tape lights work the same way except all you needMoreSimply fasten with the included clips and plug in tape lights work the same way except all you need to do is remove the adhesive backing. And press onto the cabinet. Some even come with a remote.
Can you use LED strip lights under cabinets?
Under the Cabinets. If your kitchen has a row of wall cabinets, stick the LED lights along their bottom, or along the kitchen console table. Then adjust the color to whatever you like depending on kitchen decoration style and your preferences, and make the kitchen exude a different aura.
How do you hide the power cord for LED strip lights?
0:025:14Concealing and Managing your LED lighting wires - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou use three-quarter inch or larger double-sided foam tape you're going to need to trim it off ifMoreYou use three-quarter inch or larger double-sided foam tape you're going to need to trim it off if you use a half-inch. It should fit right on there. And you won't need to do any trimming.
How do you install LED strip lights over cabinets?
0:316:18How to Install Above-Cabinet and Under-Cabinet LED Lighting Using ...YouTubeStart of suggested clipEnd of suggested clipFor the under cabinet install begin by measuring the space under your cabinets to determine how muchMoreFor the under cabinet install begin by measuring the space under your cabinets to determine how much strip lighting you'll need don't include cabinet lips in these measurements.
How do you install strip lights?
0:203:10How to Install, Cut & Connect LED Strip Lights - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can use fixing clips to strengthen the strip light's installation and ensure that they stay inMoreYou can use fixing clips to strengthen the strip light's installation and ensure that they stay in place peel off the adhesive tape and apply it to the surface with a non-sticky. Area over the strip.
How do you hide under cabinet lighting wires?
Cable Protectors One way to do this is by bundling the wiring carefully and compactly into a bundle and then using tie wraps to hold it in place. You can then stick it the underside of the cabinet using staples (being careful of course not to pierce the wiring and ruining all your hard work).
What is the best type of under cabinet lighting?
LED lighting is also the most energy efficient and long-lasting. Moreover, because it emits very little heat when on, it is perfect for use under kitchen cabinets, where food may be stored. Best of all, LED can produce a range of colors, from warm to cool.
How do you hardwire under cabinet LED strip lights?
0:061:17Hardwired, LED, Under-Cabinet Lighting Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou use a jumper to go from that box into your first led fixture and then jumpers to go between theMoreYou use a jumper to go from that box into your first led fixture and then jumpers to go between the other fixtures it cleans your installation.
How do you fit LED kitchen strip lights?
1:5610:01How To Install LED Strip Lights Under Kitchen Cabinets (Under ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're gonna take our LED strip. Now we're gonna size it. Up. So if we take a close look at our LEDMoreWe're gonna take our LED strip. Now we're gonna size it. Up. So if we take a close look at our LED lights about every two and a half inches we're gonna see this symbol in the middle there's actually a
Can you plug LED strip lights into an extension cord?
The Single-Color LED strips need a 2 pin LED extension cable. The cables themselves finish off at either end with common 2.1mm size barrel plug adapters that are used with all single-color strips and dimming controllers.
How do you make LED strip lights look good?
0:295:11Light Strips in 6 Unexpected Places - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd i had to cut the covers with a small hacksaw to fit the mirror. It was pretty easy though i putMoreAnd i had to cut the covers with a small hacksaw to fit the mirror. It was pretty easy though i put it on the inside of the mirror.
How do you install LED strip lights?
0:101:27How to Install LED Strip Lights - The Easiest Video Guide Everyone Can ...YouTubeStart of suggested clipEnd of suggested clipLink the controller to the light strip and connect the adapter. Finally connect the adapter to theMoreLink the controller to the light strip and connect the adapter. Finally connect the adapter to the mains. And turn the light on. Now. You can feel free to change and choose the light color atmosphere.
What kind of light goes under kitchen cabinets?
Light Source LED lighting is also the most energy efficient and long-lasting. Moreover, because it emits very little heat when on, it is perfect for use under kitchen cabinets, where food may be stored. Best of all, LED can produce a range of colors, from warm to cool.
How do you install toe kick LED lights?
0:288:33How to install Motion activated LED kick toe lighting - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you want to know how to wire it check out my other video how to wire an led strip. It shows youMoreIf you want to know how to wire it check out my other video how to wire an led strip. It shows you the basics of how to do this i just wanted to save some time right now so i've already done it.
Pre Installation: Selecting The Lights and Power Supply
LED strip Lights: You first must choose which color and brightness is needed for the under counter LED strip light installation. While for task lig...
Step 1: Double Check Your Lights Before Cutting Or Installing
When installing LED strip lighting under your counters, cabinets, or inside coves, it is very important that you test the LED lights before any ins...
Step 2: Take Measurements and Make Cuts
Flexfire LEDs CEO Brent Mauriello is pictured here measuring the length of the counters where the LED strips are to be installed. Before starting a...
Step 3: Preparing The Strip-To-Power Connection
To attach the first section of lights into the dimmer and power supply, we need to add some length of low voltage extension wire to the end of the...
Step 4: Connecting Two Lengths of LED Strips With Strip-to-Strip Connector
In the final photo of the completed installation, you will notice a 90 degree angle at the corner of the bar. To go around this corner, we had to c...
Step 5: Combining Strips With Strip-to-Strip "No Wire" Connectors
For runs longer than 16 feet, we need to connect two separate runs of LED strips. There is no for wire in the middle of the connectors, as we wante...
Step 6: Test The Strip (Important)!
Use a 2-way terminal block or wire nuts to temporarily connect the full length of LED strip lights with the power supply. If everything is wired co...
Step 7: Install The LED Strips Under The Counter
Wipe down the under surface of the counter and make sure it is clean. The 3M take will stick to most non-porous and flat surfaces. For applications...
Step 8: Installing The Dimmer
To mount the dimmer to the wall, we suggest using 3M Command Hanging Strips. Next, wire the unplugged power supply into the dimmer by running the w...
Step 9: Turn on The Lights!
The last step is the easiest, but also the most fulfilling step in the whole process. Now all you have to do is plug in the power supply, turn up t...
How to install LED strip lights?
Step 1: Double check your lights before cutting or installing 1 Lay out all the products to create a mock installation to make sure you have all the supplies necessary 2 Unroll the LED strip lights from the plastic reel 3 Attach the uncut lights to the power supply and turn on the power supply 4 The strips should light up. If they do not, please check your connections 5 Ask yourself - "Are these bright enough?", "Will I need a dimmer", "Is the color perfect for my application?", "Are all the LEDs lighting up and functioning properly?"
How to connect LED strip lights to power supply?
Use a 2-way terminal block or wire nuts to temporarily connect the full length of LED strip lights with the power supply. If everything is wired correctly, the lights should switch on when the power supply is plugged in. If they don't come on right away at full brightness, check to see that the connectors are solidly attached and that the negative and positive wires are aligned correctly onto the strip.
What color LED strip lights are needed for under counter lighting?
LED strip Lights: You first must choose which color and brightness is needed for the under counter LED strip light installation. While for task lighting and high brightness applications we recommend UltraBright LED strip lights, for accent lighting installations we recommend ColorBright LED strip lights, which feature 600 LEDs per reel and are sufficient for almost all under counter LED lighting situations. It's always recommended to go brighter than anticipated and add a dimmer for greater control. Who knows when you will need that extra task lighting.
How many feet does a ColorBright strip use?
View the chart here. We used under two reels (around 28 feet) for this installation. The ColorBright strips use 2.9W per foot. So around 81W in total. Typically, you need to choose a power supply with an extra 20% capacity than the load you are requiring for various reasons, so we selected a 100W 12V Mean Well Unit.
What to ask yourself when you are lighting up LEDs?
Ask yourself - "Are these bright enough?", "Will I need a dimmer", "Is the color perfect for my application?", "Are all the LEDs lighting up and functioning properly?"
How many diodes are cut on LED strip?
Note: LED strips can only be cut along the clearly marked lines that are evenly spaced. On this LED strip, the cut lines are after every three diodes all the way down the strip.
Can you use LED strip lights on a cafe?
With a little imagination and a clear picture of your project in mind, you can do just about anything with LED strip lights! Flexfire LEDs recently installed dimmable under counter LED lighting at a local cafe. Read on to learn exactly how it was done and gain some knowledge for your next home or commercial business LED strip light installation.
How to install LED lights on cabinets?
This allows the LED tape to travel underneath the cabinets. To install the LEDs against the face frame, slice through cabinet sides with an oscillating tool. Don’t press the tape in place yet.
How to cut LED tape for corner cabinets?
From the middle of the corner cabinet, measure the length of tape needed to cover the cabinets along one wall. Use scissors to cut the LED tape across the center of the copper contacts , as shown. Repeat the process for the other wall of cabinets.
How to connect LED tape to a sink?
Align the polarity of the free end of the tape and an extension, and clamp down the connection. Fish the wires up through the hole and into the corner of the cabinet. Measure, cut, and add extensions to enough LED tape to cover the underside of the cabinet above the sink. Push the wires through the hole in the taller cabinet. Twist together the two stripped positive wires and secure them with low-voltage wir ing nuts. Repeat the process for the negative wires, as shown. Tuck the wires into the corner of the cabinet’s face frame.
How to connect LED lights to a splitter?
Use LED tape-light extension connections to turn the terminal into a splitter, sending power to both walls. These 4-foot extensions have two wires, white for positive and white with a black stripe for negative, with a clamp on one end that grips onto the LED tape. Join the tape to the extension by peeling away the adhesive backing under the copper contacts. Slide the tape into the connector with the logo facing up, as shown. Make sure to align the polarity of the extension to the markings on the tape. Wiggle the tape in so it seats completely. Flip the connector over and snap the lock closed with a slotted screwdriver. Repeat this process for the LED tape running under the other wall of cabinets. Then twist together the positive ends of the extensions and fit them into the terminal across from the red wire. Tighten the setscrew and add both negative wires to the terminal in the same way.
How to get 120 degrees of light on backsplash?
Restore the power at the panel . Hold the tape to the underside of the cabinet and adjust the light’s coverage. Keep the strip 1 to 2 inches back from the face frame to distribute the 120 degrees of light evenly across the backsplash and countertop , as shown. If you have a dark countertop, install the tape against the back of the face frames, with the LEDs pointing toward the backsplash, to eliminate bright spots.
