Installing Trex Riser Lights NOTE: Install stair lights after stairs and risers have been installed. Mark locations for each light, generally 4 inches above the stair tread. Drill a 1 inch diameter hole at least 1 inch deep into riser. If riser material is thicker than 1 inch, use a 1/2 inch drill bit to create a passage for wires.
Full Answer
How do you use Trex deck light timer?
Trex.rce HOW TO INSTALL TREX DECKLIGHTING/CONTINUED Timer Operation Instructions 1. Select the mode of operation: » Dusk to Dawn » 2–8 hours » Always “ON” » “OFF” Program repeats daily. When power is flowing to lights, green light above POWER is on. Installing Post Cap Lights NOTE: Install post cap lights after the railing system, post
How do you install riser lights on stairs?
Installing Riser Lights NOTE: Install riser lights after stairs and risers have been installed. 1. Mark locations for each light, generally 4"(102 mm) above tread. Consult local codes for lighting requirements. NOTE: If possible, avoid locations over stringers as holes will be more difficult to create.
What are the best tips for installing Trex lighting?
HELPFUL TIPS » Please note that Trex lighting operates on DC power. NEVER mix AC and DC fixtures on the same circuit. Doing so will result in extremely premature fixture failure and is not covered by the Trex limited warranty. You must use a Trex transformer on all Trex lighting installations. » Never fully drive staples when securing wire.
How do you install recessed lights on a wood deck?
Installing Recessed Deck Lights NOTE: Install recessed deck lights after installing decking. 1. Mark locations for lights in deck boards. NOTE: If possible, avoid locations over joists, as holes will be more difficult to create. 2. Drill a 1" (25 mm) diameter hole 3/4" (19 mm) deep into deck board.
How do you connect Trex riser lights?
5:307:14How to Install Trex LED Deck Lighting | Trex - YouTubeYouTubeStart of suggested clipEnd of suggested clipPress the light into the hole ensuring. The lens is horizontal. Make connections behind the stairsMorePress the light into the hole ensuring. The lens is horizontal. Make connections behind the stairs using the male lead wire from the riser light and the female connection on the splitter.
How do you install Trex stair riser lights?
Installing Trex Riser Lights Thread wires through hole. Press light into hole, ensuring lens is horizontal. Make connections behind stairs from male lead wire from recessed light into female connection on Trex light splitter. Also attach male-to-male connection wires in between each splitter.
How do you install riser lights?
0:072:10How to Install Lights on a Deck Riser - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a pencil or sticker to mark where you're going to drill measure twice and drill once. Now forMoreUse a pencil or sticker to mark where you're going to drill measure twice and drill once. Now for the drilling keep your drill straight and wear the proper ppe. Use our drill bits.
How far apart should Trex riser lights be?
Riser lights installed on the risers and should 36”-72” (0.9-1.8m) apart, depending on the width of the stairs.
Where should decking lights be placed?
If you have drilled correctly, your lights should fit into the holes that you have drilled into the decking. Once you have placed the lights in the holes, you can connect the back of each light to the loom socket behind the decking.
How do you install composite deck lights?
1:272:59How to Install Deck Lighting with Wickes - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce all the lights are in place add the blanking plugs to the final socket then connect the driverMoreOnce all the lights are in place add the blanking plugs to the final socket then connect the driver cable in sasaki closest to the plug.
How do you hang lights on a Trex deck?
0:254:06How To Hang String Lights On A Deck - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo my crazy idea is to use Shepherd's hooks to hang the lights from I'll mount them on the outsideMoreSo my crazy idea is to use Shepherd's hooks to hang the lights from I'll mount them on the outside of the deck it'll sit right here on the deck. And then the lights will hang above.
How do you install LED lights on deck stairs?
Here's how to install them.Gather the stair-lighting hardware. This type of LED light fits flush into the riser. ... Bore holes in risers. Mark the location for each light. ... Drill wire access hole. ... Push in the wires. ... Add caulk. ... Push in the light. ... Let caulk dry. ... Run cable.More items...
Does Trex make stair risers?
Available in 12 foot lengths to accommodate your deck layout, the Trex Transcend Riser Boards can be ordered in the 1 inch x 8 inch dimension to suit your staircase needs.
How many step lights do I need?
We recommend installing 1 light every 3 steps or so, but you can play with this number depending on how bright you want your staircase to be.
How do you space a stair light?
It's recommended that each step light has a minimum distance of 18 inches between it and any other right beside or below it to ensure that the light is dispersed evenly across each step. Generally you should be aiming for 3-4ft apart for ideal results most of the time.
How far apart should deck step lights be?
A general rule of thumb is to place lights every 3-4 feet on each step on wider steps, but the answer to this question depends on how wide your steps are and how many steps you have in each location.
Does Trex make stair risers?
Available in 12 foot lengths to accommodate your deck layout, the Trex Transcend Riser Boards can be ordered in the 1 inch x 8 inch dimension to suit your staircase needs.
Why are my decking lights not working?
Some of my lights won't light up: -Check the polarity and security of your wire connections. -Check to see if they work individually by checking each one alone with the transformer. -If some lights just stop working suddenly, look at the wire/cable connecting to them.
Is Trex transformer waterproof?
The 100W Trex Transformer is designed specifically for outdoor use, withstanding years of tough weather including rain, wind and hail.
Are Trex deck lights dimmable?
Trex® Remote Dimmer Trex deck lighting dimmer is the ideal way to turn simple illumination into a perfect mood setter. And you can expand your landscape lighting options by adding a dimmer. For extra control, use multiple dimmers and multiple circuits to control each type of light separately.
How to make a riser light?
Drill a 1 inch diameter hole at least 1 inch deep into riser. If riser material is thicker than 1 inch, use a 1/2 inch drill bit to create a passage for wires. Thread wires through hole. Press light into hole, ensuring lens is horizontal.
Where to install Trex splitter?
Install a Trex lighting splitter at every post base where lighting will be added and depending on spacing in between each riser and recessed light.
What is Trex deck lighting?
Rich color-coordinating finishes, durable composite and aluminum materials, and modern designs; Trex Deck Lighting offers an amazing option to provide safety for nighttime enjoyment as well as a chance to add a touch of magic to your deck design.
How to get LED light into hole?
Do not pull the LED light into hole by pulling on the wires. This may damage wires or the LED fixture itself. Press light into hole until flush with surface.
Where to place post sleeve?
Place post sleeve over pressure-treated post and mark desired height, centered on post sleeve for deck rail light location.
How to install motion controller?
If you plan to use the motion sensor capabilities of this unit, place it in a location that allows the center of the unit to face the location of the motion. For example, the door leading onto the deck, or at the bottom or top of stairs are common locations. However, the most important consideration of Motion Controller location is how you will install it into your lighting circuit. See illustrations on next page for some basic examples.
How to adjust sensitivity on a motion sensor?
Use the +/- buttons to adjust the sensitivity of the motion sensor. There are 9 steps between maximum range and minimum range. The indicator light will blink twice when either limit is reached. The lowest limit will deactivate the motion sensor.
How far away from ground should a dimmer remote be installed?
2. Dimmer should be installed in a dry location. 3. Timer must be installed vertically with receptacle facing downwards. Timer must be at least 1' (.305 m) from ground level when installed as per federal safety code height regulations. Timer must be in view of the sun to use the dusk/dawn feature. Installing Wiring
Why install a GFCI outlet on deck?
These should be accessible for service. Installing a GFCI outlet is REQUIRED to help prevent damage to lighting from electrical surges.
Where are the splitters mounted?
NOTE: All wiring and splitters are mounted to the inside of framing. Picture above is a general representation of where to place them. WARNING: » DO NOT INSTALL DECKLIGHTING IN CLOSE PROXIMITY TO POOLS OR HOT TUBS, AS CHEMICALS FROM THE WATER CAN DAMAGE LIGHTING FIXTURES. » DO NOT INSTALL WIRING UNDER HEAVY WEIGHT OR LOAD AS THIS CAN DAMAGE WIRING.
Do you need to install wiring before railing?
NOTE: It is recommended to install wiring and splitters before decking and railing have been installed.
Can you run wires between joists and deck boards?
NOTE: Install wiring and splitters before decking and rail- ing have been installed. DO NOT run wires between joists and deck boards.
What to do if deck boards are not installed yet?
NOTE: If deck boards are not installed yet, place a deck board on framing to ensure post sleeve is at correct height.
Do you attach wires to splitters?
Continue until all wiring from lights is attached to splitters and connector wires are attached in between splitters.
