Place the shutter over the Shutter-Clips and press the ribs of the shutter on to each Shutter- Clip. Press the shutter firmly against the mounting surface being sure all six clips engage. With it's front facing the mounting surface, align the shutter next to where it will be mounted.
Full Answer
How to install shutters over vinyl siding?
- A tape measure
- Shutters
- A pencil
- A level
- A drill. Your drill bit should be slightly larger than your screws.
- A screw gun
- Screws. The length depends on the thickness of the shutter and siding lap.
- A ladder if installing shutters on the second-story of a home .
How to install louvered or raised panel shutters?
- Use a drill with a multi-purpose 11/64-inch bit to pre-drill holes through the shutter for the screws at each reference mark.
- Reposition the shutter on the wall.
- Use the holes in the shutter as a guide to bore into the wall surface to a depth of 3-1/4-inches.
What is the best installation for your roller shutters?
Roller shutters can be fitted one of two ways: outside the window or inside the window opening. If you fit your roller shutters outside the window, it will appear flush with the wall around the window. Alternatively, you can fit the shutters inside the alcove created for some windows, so that it appears framed by the wall around it.
How do you clean the vinyl shutters?
Shutters in Two-Story Houses
- Fill a hose -end sprayer attachment -- a bottle that attaches to a hose -- with all-purpose outdoor detergent.
- Test the detergent on a small inconspicuous section of shutter first. Attach the bottle to the hose.
- Turn the control to release the detergent into the flow of water. ...
How do you install clip shutters?
Hold the shutter against the mounting surface in the position where it will be attached. Mark the center hole of each shutter clip (4 places). Draw lines vertically between the top and bottom marks. After completing Step 2, remove the Shutter-Clips from the shutter.
How do you install vinyl shutter fasteners?
1:302:36How to Install Vinyl Shutters on Exterior Windows with ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipDrill an 8 inch diameter hole 1 and 3/4 inches deep at each of the points. Although shutter slightsMoreDrill an 8 inch diameter hole 1 and 3/4 inches deep at each of the points. Although shutter slights are preferred screws can be used to install on brick.
Should I use shutter spikes or screws?
Screws are primarily used to attach outdoor shutters to wood and other soft siding. Spikes are designed to secure shutters to masonry, brick, stucco, hardboard or other hard surfaces.
How do you install shutter spikes?
1:502:53How to Install Vinyl Shutters with Spikes to Exterior Brick, Concrete ...YouTubeStart of suggested clipEnd of suggested clipYou after all spikes are started returned to tap each spike until the head connects with a shudder.MoreYou after all spikes are started returned to tap each spike until the head connects with a shudder. Face. Repeat this process for the opposite side shudder and stand back to admire your.
How are vinyl shutters attached?
Newer model shutters are mounted by hanging on a metal clip screwed into the wall. Older model vinyl shutters use a mounting clip called a "shutter lok." Shutter loks mount through existing holes in the shutter that extend to the house facing surface.
How many screws go into a shutter?
For shutters up to 55", use four screws per shutter. For shutters 55" and over, use six screws per shutter. See figures at right. For use on any surface including: wood, aluminum, vinyl, stucco, hardboard, brick, fiber cement, or masonry.
What kind of screws do you use on vinyl shutters?
Exterior vinyl painted screws are the perfect vinyl shutter screw to install your vinyl shutters.
What screws to use for plastic shutters?
Painted metal screws are typically used by home improvement contractors to install exterior vinyl shutters.
What screws to use to attach shutters?
Painted metal screws are commonly used by home improvement contractors to install exterior shutters. They work great when you are mounting exterior shutters on siding or real wood.
How do I remove shutters with hidden clips?
0:469:30Removing Shutters with Shur-Lok Fasteners. Window ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipThem off if we have to just want to take your five in one just get them underneath the shutterMoreThem off if we have to just want to take your five in one just get them underneath the shutter button and you're going to tap them lightly till it actually cuts.
How do you remove shutter spikes?
0:081:52Remove Shutter Spikes & Replace Vinyl Shutters - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe used a standard pry bar for this effort newer stronger spikes may pull out intact. While otherMoreWe used a standard pry bar for this effort newer stronger spikes may pull out intact. While other older more frail spikes may break in the process like what happened.
How are shutters attached to siding?
Attach vinyl shutters to siding using plastic exterior shutter fasteners, which are also called locks or plugs. Drill pilot holes, and then fasten the shutters to the home's exterior by driving the plugs in with a hammer.
How do you attach decorative shutters to vinyl siding?
4:465:52Perfect Shutters, inc. Vinyl Shutters Installation Instructions - YouTubeYouTubeStart of suggested clipEnd of suggested clipAfter you have used the shutter to mark the mounting hole locations on the building drill a 1/8 inchMoreAfter you have used the shutter to mark the mounting hole locations on the building drill a 1/8 inch diameter hole through the siding. And into the wall at least 1 and 3/4 inches deep at the marks.
How do you hang shutters on vinyl siding without drilling?
If mounting the shutters to vinyl siding, use exterior shutter fasteners, which lock the shutter to the house while allowing them to expand and contract without damaging the shutter or the vinyl. Install the locking fasteners using a hammer.
How do you hang batten shutters on a board?
2:453:56DIY Board and Batten Shutters - YouTubeYouTubeStart of suggested clipEnd of suggested clipThen hold the shutters up to the windows. And pre-drill into the house pre drilling will keep theMoreThen hold the shutters up to the windows. And pre-drill into the house pre drilling will keep the wood from splitting then attach the shutters to the house with the lag screws.
How do you attach wood shutters to vinyl siding?
Step-by-Step Guide to Install Shutters on Vinyl SidingStep 1: Measure your windows. ... Step 2: Check for the right screw length. ... Step 3: Drill pilot holes in the shutters. ... Step 4: Drill holes in the siding. ... Step 5: Install spacers. ... Step 6: Attach the shutters.
How to attach a shutter clip to a shutter?from buildersedge.com
Push a shutter clip onto the ribs at each corner of the shutter. The mounting tab should extend beyond the shutter. See Figure 2. Shutter clips will be removed later, so DO NOT fasten shutter clips completely onto the shutter at this time.
How to attach shutters to mounting surface?from buildersedge.com
Hold the shutter where you want it to be attached on the mounting surface. Mark the center hole of each shutter clip in each clip. Draw lines vertically between top and bottom marks. After completing this step, remove shutter clips from shutter. See Figure 3.
How many times to transfer dim C to window header assembly?from buildersedge.com
Transfer Dim. C to the window header assembly twice, once on each side of the centerline. See Figure 2C.
How many shutter loks are needed for a shutter?from buildersedge.com
Note:Up to 43", use four (4) Shutter-Loks or screws. 44" and greater, use six (6) Shutter-Loks/screws per shutter.
How deep should shutters be in brick?from buildersedge.com
With shutter in location against the wall, drill through shutter into the wall to depth of 3-1/4". In brick, the hole diameter should be no greater than 1/4", and drilled into mortar joints. Do not attach shutter at this time. See Figure 1.
How to install a transom clip?from buildersedge.com
A transom clip will also need to be installed in addition to the two (2) clips. Start by pushing one end of the transom clip onto the shutter, clamping the shutter to the top. Work the transom clip down until the entire clip is fastened to the shutter. Be sure the transom clip is pushed on as far as it will go. See Figure 1.
How many holes do shutter bolts need?from buildersedge.com
Holes should be centered within the side rails and in line with the top, bottom and center rails (for six screw application). Shutter-Loks require 1/4" hole, screws require 11/64" hole and 1/4" hole if over 44". See Figures 2A and 2B.
Where to drill holes in shutters?
The best position for drilling the holes is at the four corners of the shutter, the center of both vertical sides, and the top and bottom panels. This will secure the shutter to the siding.
How much space between window shutters?
Hold the shutter against the edge of the window, and leave a ½ inch space between the two. The space is essential to allow the shutter to expand and contract with temperature changes.
How to prevent breakage in shutters?
By pre-drilling holes in the shutters and siding, you will prevent breakage and take the hassle out of driving in the fasteners. With the right tools and a little help, you can have like-new windows or doors in no time.
Why do I need spacers between shutters?
I recommend using spacers between the shutter and siding for extra protection against breakage. This step is not mandatory but if you want to be extra careful with your siding, using spacers is a smart choice.
How to check if shutter is positioned correctly?
Have someone else hold the shutter in position as you drive screws into the holes. Use a spirit level to check the shutter is positioned correctly on either side of the window.
How to measure for shutters between two windows?
Use a tape measure and note the height of your window. If you are installing shutters between two windows, measure the space between them to buy shutters of the right width to avoid overlapping.
Where to drill for siding?
When drilling siding, place the drill bit at the center of the panel’s rib, which is easier to penetrate. Avoid drilling the siding’s profile as it is thicker, harder to penetrate, and can cause breakage. The screws may also wobble and sit loosely, which is no good for the shutter.
How to remove shutter spikes?
Simply use a pair of snips and slide them behind the shutter to cut the shutter spike off at the shank.
How long should a shutter fastner be?
Typically the shutter fastner will be just under 3" long . Grasp the shutter fastener supporting shank and push it through the shutter hold and into the wall surface. Tap the shutter fastener gently with a hammer to snug the shutter against the siding. Do not over tighten, or this will cause the shutter to dimple.
