How do I know what type of toilet I have?
First thing you need to do is figure out what brand of toilet you have. You can find this either inside the lid of the tank, or down right behind the bowl like below: After you have the brand, then you’ll also want to know the serial number. For example, I found the serial number for my toilet on the inside of the toilet tank here:
How do you measure the height of a toilet tank?
Measure the toilet tank height to be sure the new toilet will fit underneath shelves or anything else that’s currently above the old toilet. A toilet tank’s height is measured from the floor to the top of the toilet tank. Place the end of the tape measure on the floor, and take the measurement at the very top edge of the tank lid.
How do I know if my toilet tank needs to be replaced?
If you tell them the brand name and the serial number, they’ll likely be able to help you find the right replacement tank. If you’re not confident that you’ll be able to easily find a perfectly fitting replacement tank for your toilet, then you may want to take a few measurements.
How to measure for a new toilet bolt?
First, measure the distance between the rear bolts of the toilet and the wall. In addition to that, measure the distance from side walls to the bolts as well. Make sure that you check the bolt configuration too.
How to measure the height of a toilet tank?
Where is the rough in on a toilet?
What is the phone number for a plumber to install a toilet?
What happens when a toilet ages?
See 1 more
About this website
How do I know if my toilet is 10 or 12?
If your toilet has four bolts rather than the standard two, you'll measure to the center of the rear bolts. The standard rough-in measurements are 10, 12 and 14 inches. If your measurement is in between these intervals, round your number down to the nearest standard measurement.
Can you replace a toilet with any size toilet?
You can measure the existing toilet to get a good idea of the current size that is installed, but you don't need to choose a toilet that is the exact same size as long as it fits comfortably in the space.
What measurement do you need to replace a toilet?
The most important measurement you can take for a replacement toilet is the rough-in dimension. This is the distance between the bolts that hold the toilet to the floor and the wall. Make sure you measure from the centre of the bolts, up to the drywall (as opposed to the baseboard).
How do I know the rough-in size of my toilet?
Here's how:Identify where the toilet is bolted to the floor. Look for small bolts or caps at the base of your toilet. ... Measure from the wall to the center of the toilet's base bolts. Doing so will provide you the toilet's rough-in distance.Avoid measuring from baseboards or other moldings. ... Check your work.
Can you replace a toilet without replacing the floor?
They often ask if they should remove the toilet before installing a new bathroom floor. While it is possible to install a new linoleum or ceramic tile floor without removing the toilet, it is not recommended and actually can increase the labor involved in the project.
Can I replace an elongated toilet with a round toilet?
Round toilets have an average length of 16.5 inches. You cannot replace an elongated toilet seat with a round toilet seat. You can, however, replace an elongated toilet with a round toilet. You just need to make sure that the rough-in measurement is the same.
Can you replace a 10 inch rough-in toilet with a 12-inch?
Ideally, the toilet's rough-in should match the rough-in for your bathroom plumbing. However, even if a toilet is designed for a 10-inch rough-in, you can still install it into a space that has a 12-inch rough-in.
Are toilets a standard size?
The simple answer to the question “Are toilet seats a standard size?” is no. Unfortunately, toilet seats aren't produced in a standard size, however, that doesn't mean you can't easily find a replacement for your own toilet.
What does 12-inch rough-in mean for toilets?
“What does 12-inch rough-in mean for a toilet?” That means there is 12-inches between the center of the toilet flange to the finished back wall. This information can be found on the toilet's specification sheet.
What are the four types of toilets?
What are the different types of toilets?Low-level toilet. Low-level toilet - the cistern is positioned on the wall just above the pan with a short length of plastic pipe connecting the cistern and the toilet. ... Close-coupled toilet. ... Back to wall toilet. ... Wall hung toilet.
How far off the wall should a toilet be?
Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture. (The NKBA actually recommends 32 inches.) There should be at least 24 inches of clear space in front of a toilet or bidet.
How far from the wall should a toilet rough in Be?
In general, the toilet rough-in distance is 12″ from the center of the toilet flange to the back wall for a typical toilet. There should also be a minimum of 15″ from the centerline of the toilet to any wall or object on either side of the toilet.
Can you replace a 10 inch rough-in toilet with a 12-inch?
Ideally, the toilet's rough-in should match the rough-in for your bathroom plumbing. However, even if a toilet is designed for a 10-inch rough-in, you can still install it into a space that has a 12-inch rough-in.
Do all toilets fit the same flange?
Toilet Flange Sizes & Dimensions Sizes of toilet flanges range from the standard four by three inches, four-inch, or three inches flange with the option of an odd fit. To get these dimensions, you measure the widest part of the flange, usually the top and bottom opening.
Are toilets a standard size?
The simple answer to the question “Are toilet seats a standard size?” is no. Unfortunately, toilet seats aren't produced in a standard size, however, that doesn't mean you can't easily find a replacement for your own toilet.
Are all toilet flanges the same size?
What Is The Standard Toilet Flange Size? Flanges come in just two standard sizes: 3 and 4 inches. You're most likely to find 4×3 flanges when you look in a local hardware store. This model has two different diameters.
Do I need a specific toilet seat for my toilet?
But there are many different options available that can provide different levels of comfort and support. If you have any questions about which toilet seat would be best for your needs, you should consult with a plumber or another professional who can help you select the right product.
Are toilet seat fixing holes Standard?
The vast majority of toilet seats will have standard holes for fixing, however it is always worth checking before purchasing a new seat.
How do you replace a toilet enclosed toilet seat?
To replace an enclosed toilet seat, remove the bolts that hold the seat in place, then install the new seat in the same location.
What are the different types of toilet seats?
The three most common types of toilet seats are round, elongated, and bidet. Round seats are typically found in smaller bathrooms, and elongated seats are often found in larger bathrooms. Bidet seats are becoming more popular in North America, and are often found in luxury bathrooms.
Are toilet seats all the same size?
Toilet seats vary in size, with the most common seats measuring between 14 and 15 inches in length.
Are all toilets universal?
No, all toilets are not universal. Some toilets are designed for specific applications such as RV toilets, marine toilets, and composting toilets.
What is the point of slow close toilet seat?
One reason is that it can help to prevent the seat from slamming down, which can be noisy and jarring. Additionally, a slow close toilet seat can help to prevent the seat from being accidentally left up, which can save water and help to prevent accidents.
Is a one piece toilet more expensive than a two piece toilet?from plumbingsupply.com
Note that the previous example is regarding one-piece (typically more expensive) toilets as compared to two-piece toilets that are usually less expensive. Most two-piece toilets use parts that are generally replaceable without the need to buy OEM parts. OEM parts can be more expensive than "will fit" parts and since the tank can be removed from ...
Can you use OEM parts on faucets?from plumbingsupply.com
It's not as critical to use OEM parts for external trim plates or handles for faucets since these parts can normally be replaced without the need to turn off the water to your entire house. In many cases, if the faucet is too old you will only be able to find "will fit" trim or handles anyway.
Do toilets have OEM parts?from plumbingsupply.com
And, in some cases you will definitely want to use an OEM part. Most toilet manufacturers buy most of their internal fill valves, flush valves, and flappers from other companies that specialize in making fill valves, flush valves or flappers. But sometimes they manufacture their own fill valves or flush valves.
What to consider when buying a toilet?
Measurements. Taking measurements is the first and most important step before buying a toilet. First, measure the distance between the rear bolts of the toilet and the wall.
How tall is a toilet bowl?
Most toilets usually have a standard height of 14 to 16 inches.
How much water does a dual flush toilet use?
These toilets feature two levels of flushing, which include a full flush and a partial flush. A full flush consumes about 1.6 gallons of water, whereas a partial flush only consumes about 0.8 gallons of water. You can choose between these levels depending on your preference and business.
Why are rear outlet toilets different from floor?
Furthermore, rear-outlet toilets are configured a bit differently because the waste in these toilets exits through the bathroom wall instead of the floor. The measurements for these toilets are the distance from the finished floor to the center of the waste outlet.
What is a one piece toilet?
One-piece toilets, as the name indicates, are in one piece, which means that you cannot separate the toilet bowl and the tank. These toilets provide a seamless look which adds to their style. One-piece toilets are easier to clean because they don’t have as many gaps and crevices as two-piece toilets.
Why are elongated toilet bowls longer than round toilet bowls?
Elongated bowls are two inches longer than round-front toilet bowls because they provide added comfort. Therefore, if you want to go for an elongated bowl, make sure that your bathroom has enough space. And make sure the elongated bowl won’t interfere with the door, drawers, or any other items in the bathroom. 3.
What is a siphon toilet?
Siphonic toilets consist of an S-shaped drain trap. When you activate the flush, the waterway fills up with water, and the tank quickly releases a large quantity of water into the bowl, generating a siphon action to increase the performance of the flush. This way, the flush empties rapidly.
What is the most important thing to know when looking for a new toilet?from wayfair.com
One of the most important aspects in searching for a new toilet is its size and dimensions. Read our guide to learn more about the features that impact standard toilet dimensions, how to measure a toilet, and how to use this information to ensure a smooth installation and bathroom layout.
What are the Dimensions of a Standard Toilet?from homenish.com
Standard toilet sizes are usually between 27 to 30 inches deep ; that is 69 to 76 cm, about 20 inche s in width, i.e., 51 cm, between 27 to 32 inches in height (68.5 cm to 81 cm), and features a rough-in of anywhere from 10-12”. You won’t want to have a large toilet in a tiny bathroom, so the dimensions of your toilet are important.
How does a toilet handle work?from homestratosphere.com
Your toilet’s handle fully controls when the water flushes out from the bottom bowl and new water from the tank flows in. When you press down on the lever, it lifts off the flush valve chain, which lifts the flapper, allowing all of the water in the tank to flood into the toilet bowl and thereby push out the excess waste. The other components of the water tank are designed to ensure your tank fills up to the level necessary to complete that whole flushing process again.
How far should a toilet seat be from the floor?from homenish.com
To be ADA compliant, the distance from the floor to the peak of the toilet seat should be between 17”-19”. This is about 43.1-48.3 cm. Note that this distance is measured to the top of the toilet seat and not to the rim of the toilet bowl. Until recent times, standard toilets were about 15 inches long, that’s about 38.1 cm. This was a few inches shorter than ADA accessibility requirements.
What are the two shapes of toilet bowls?from homenish.com
The toilet has two bowl shapes, namely, round and elongated bowls.
How much water does a low flow toilet use?from familyhandyman.com
Since 1994, low-flow toilets that use 1.6 gallons per flush (gpf) or less have been the federal standard. The first generation of low-flow toilets sucked—or rather, they didn’t. That’s mostly because manufacturers tweaked a few things to reduce the amount of water used but didn’t change the basic design.
Why is a toilet important?from familyhandyman.com
While the color and cost matter, how much water it uses and how well it flushes matter more. A good one conserves water and generates enough power to clean the bowl in a single flush. (A bad one can be a 20-year pain in the butt.)
What is the most important thing to look at when buying a toilet?
While extra features and components are fun and important, the most important thing to look at is toilet dimensions . After all, you don’t want to get a toilet with an elongated seat if your bathroom is narrow.
What to consider when buying a new toilet?
When shopping for (or simply researching) a new toilet, it is important to consider the different product features that matter to you. You’ll have to consider important factors outside of your personal taste.
What is the difference between a back to wall toilet and a wall hung toilet?
The main difference between a back-to-wall toilet and a wall-hung toilet is that a wall-hung toilet appears to be suspended above the floor, without touching the floor.
Why are wall hung toilets so attractive?
Wall Hung toilets are attractive as there’s no gunk or build-up that commonly occurs at the base of the toilet because there is no base. Instead, the toilet is hung on the wall and the outgoing sewer pipe cuts through the wall and drains down and out. Where there should be a base, there is empty space, which creates another benefit of making it much easier to clean floors.
How long is a 2 piece toilet?
The toilet seat itself spans 18.5 inches long and is just under 14 inches at its widest. In addition to being long, the Back-to-Wall Elongated 2-Piece Toilet also has some notable height advantages. The seat itself is 16.5 inches above the finished floor.
What is the outgoing hole in a toilet?
This outgoing hole is where you are going to be the central point of your toilet installation process as the holes absolutely must align and everything else can be more readily adjusted, such as adding extra length to your incoming water pipe.
Why do you want a skirted toilet?
For example, if you’re going for a modern bathroom remodel then you may prefer a modern-looking skirted toilet for its aesthetic appeal , rather than a simple wall-mounted toilet that doesn’t look as good.
How to measure the height of a toilet tank?
A toilet tank’s height is measured from the floor to the top of the toilet tank. Place the end of the tape measure on the floor, and take the measurement at the very top edge of the tank lid. Toilet bowls and seats are either round or oval.
Where is the rough in on a toilet?
The rough-in measurement of a toilet refers to the span between the wall behind the toilet and the center of the waste pipe. To measure the rough-in for your toilet, measure from the wall behind the toilet to the middle of the bolt caps (the caps holding your toilet to the floor).
What is the phone number for a plumber to install a toilet?
Get started today by requesting an estimate from your local Mr. Rooter or by calling (855) 982-2028.
What happens when a toilet ages?
As your toilet ages, it will develop leaks. Component s will fail. More efficient models will become available. When you’re tired of dealing with all the hassles of an old toilet and the time comes to replace it, getting the measurements right is key. Measuring for a new toilet is the only way to be sure you’re purchasing a suitable replacement ...
1 – Measurements
2 – Bowl Shape
- The next step is choosing the toilet shape that fits your needs. They are usually the standard shape because they take less space. If you have limited space in your bathroom, then a round-front bowl is the right option for you. They are two inches longer than round-front toilet bowls because they provide added comfort. Therefore, if you want to go for an elongated bowl, make s…
3 – Bowl Height
- The bowl height is the distance from the finished floor to the top of the toilet bowl, without including the toilet seat. Most toilets usually have a standard height of 14 to 16 inches. Taller toilets are also available in the market, and they are ideal for people with disabilities, and these toilets also comply with the Americans with Disabilities Act (ADA) requirements. ADA compliant …
4 – One-Piece Or Two-Piece
- One-piece toilets, as the name indicates, are in one piece, which means that you cannot separate the toilet bowl and the tank. These toilets provide a seamless look which adds to their style. One-piece toilets are easier to clean because they don’t have as many gaps and crevices as two-piece toilets. However, one-piece toilets are heavier than two-piece toilets, which means that you will n…
5 – Flushing Systems
- Another critical factor that you need to consider is the flushing system of a toilet. Older toilet models easily consume about four gallons of water per flush, which is a lot. It is imperative these days to buy a toilet that has a water-efficient flushing system. Standard flushing toilets have a single-lever flushing system, which only uses gravity to create the flushing pressure that boosts …