- 1. Drill a Pocket-Hole with a Kreg Pocket-Hole Jig and a Stepped Drill Bit with Stop Collar
- The Angle Creates the Oval. As you drill, the stepped drill bit enters the wood at a 15° angle. That’s what creates the distinctive oval shape.
- Parts of the Pocket. A cutaway view of the pocket hole shows all the elements, in another way. ...
- 2. Drive a Kreg Pocket-Hole Screw to secure the joint. It’s that easy. ...
- Kreg Pocket-Hole Screws Pull It All Together. As you tighten the Kreg Pocket-Hole Screw, it pulls the joint tightly together. ...
How to choose the correct KREG screw?
You can never choose any random size of the screw for your Kreg Joinery. It is important to select the appropriate size to avoid any malfunctioning. Screws used for Kreg Joinery comes in three types: zinc screws, blue coat weather resistant screw, and stainless steel screw. These types of screws vary from one another regarding the conditions they are used in.
Which KREG jig do I Need?
The Kreg 520 Pocket Hole Jig
- I recommend the Kreg 520 Pocket Hole Jig for:
- Kreg 520 Jig Pros:
- Kreg 520 Jig Cons:
- Additional Kreg 520 Features to Take Note Of: If you wanted to pick up a Kreg 520 pocket hole jig, but wanted to add a few extra bells and whistles, ...
Can you make pocket holes without a jig?
You basically drill a smaller hole before going with the big bit, and it’s an ideal technique for drilling pocket holes without a Kreg Jig. Putting those holes in the wood is simple as you need to keep your drill vertical and produce a small hole. We can’t tell you how deep, that depends on the stock and what you’re trying to do.
How to use a KREG jig on a 2x4?
You might require the following instructions:
- The first step is always to measure the thickness of your material.
- Then mark with a pencil on that piece of wood, where you want to make the pocket holes.
- After you have done this, set the drill guide in your Kreg jig. ...
- Align the thickness mark according to your measurement and lock it down.
- Then you have to set the stop collar on the bet.
What depth should I set my Kreg jig?
Adjust the depth collar to 3-5/16" (84mm) from the step of the bit for 1/2" (13mm) material and 4-1/4" (108mm) from the step of the bit for 1-1/2" (38mm) material. To set the depth, simply slide the Depth Collar onto the loose drill bit shank (the bit should not be chucked into the drill).
How do you layout pocket holes?
Place a pocket hole close to each end, and then space them out every 6″ to 8″ in between. Hopefully, these tip make pocket-hole spacing easier to understand, and will help you make strong joints that last, and make them fast on your next project.
How do you make a perfect pocket hole?
0:181:09TREND POCKET HOLE JIG - How to Make Perfect Right Angle JointsYouTubeStart of suggested clipEnd of suggested clipClamp two pieces together always remember to use a clutch setting at a single speed otherwise theMoreClamp two pieces together always remember to use a clutch setting at a single speed otherwise the screw will try and pull too far then that makes absolutely perfectly flat surface you.
Can you drill a pocket hole without a jig?
6:158:52Can you make pocket holes without a jig? - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou just need to drill an angled hole then drill a wider hole start by totaling the small hole justMoreYou just need to drill an angled hole then drill a wider hole start by totaling the small hole just like I showed before drill.
Should you glue pocket hole joints?
Pocket hole joints don't require wood glue, but that doesn't mean you shouldn't use glue when assembling your furniture projects. When a pocket screw is driven through an angled pocket hole it draws the two pieces of wood together tightly.
When should you not use pocket holes?
This one may be obvious, but you should avoid using pocket holes in locations where they will be visible. The only exceptions to this would be 1) if you don't care about the aesthetics of the piece, or 2) you are using plugs and will be painting the piece.
What is a Knapp joint?
Knapp Joints: Also known as Pin & Cove, a Pin & Scallop or Half Moon, this is a visually unique style of antique joinery, its typically very strong and can be mass-produced in a factory using a special type of machinery.
How long should a pocket screw be for a 2x4?
You should use 1.5″ pocket hole screws when joining a 2×4.
Are pocket hole joints strong?
Pocket holes are a form of wood joinery that secures screws through the edge or face grain of wood as opposed to the end grain, resulting in a much stronger joint.
What can I use instead of a pocket hole jig?
4:545:58CHEAP pocket-hole ideas for those who can't afford the expensive Kreg ...YouTubeStart of suggested clipEnd of suggested clipYou can use a sheet metal screw with the panhead.MoreYou can use a sheet metal screw with the panhead.
What can I use instead of a Kreg screw?
Alternatives to Kreg jig Pocket Hole ScrewsCSH Pan-head screws.Massca pocket hole screws.SNUG pocket hole screws.Quick Screw pocket hole screws.
Can I use regular screws for pocket holes?
1:275:42Will any screw work in a pocket hole? | MORE MINUTES - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is important because an advantage to using a pocket hole jig is that you only have to drill oneMoreThis is important because an advantage to using a pocket hole jig is that you only have to drill one hole in one board not in the receiving. Board that helps join the pieces together.
How far apart should pocket holes be?
There are no hard and fast rules for spacing pocket holes on edge joints but typically you should place pocket holes 2″ from the end of a board and then typically space pocket holes 6″ apart along the edge of the board. Use wood glue and clamps to create a quality joint.
Where do you place a Kreg jig?
0:353:00How to Use a Kreg Jig Mini - YouTubeYouTubeStart of suggested clipEnd of suggested clipPosition you must clamp the jig to the workpiece. Do not attempt to hold the jig in place while you'MorePosition you must clamp the jig to the workpiece. Do not attempt to hold the jig in place while you're drilling the pocket hole holding.
How to use pocket holes?
But the most common way to use pocket holes is a simple 90 degree angle joint. When combined with wood glue, this joint will be strong and secure for the life of your furniture.
What are Kreg pocket holes made of?
Kreg pocket hole screws come in two thread varieties: coarse and fine. Coarse screws are made for soft woods like pine and cedar, as well as plywood. This is the type of screw I stock up on. Fine screws are for hardwoods, which I haven't used yet (but plan to soon!)
How to join two boards together?
The most common way to join two boards together with pocket holes is at a 90 degree corner. While you could try to use the brute force of your hand to keep the boards lined up exactly, it's soooo much easier when you have a few clamps to act as extra, stronger hands!
How many faces are there in a pocket hole?
Pocket Hole Placement. First, a bit of board anatomy . . . There are three faces: the end grain, the edge grain and the face grain. When planning the placement of your pocket holes, keep in mind that the screws can go into the edge grain and the face grain, but not into the end grain. Imagine the board like a bundle of chopsticks.
Does a pocket hole jig hurt?
I have a pocket hole jig and use it often and with great success. It never hurts to get more advice.
Can you use pocket holes to make a board longer?
So you can't use pocket holes to make a board longer by joining two together at the end grain. But you can make boards wider! Planking multiple boards together along the edge grain is a great way to create solid surfaces without resorting to plywood. I've used this method to make wooden signs, bench lids and a desk top.
Do you need to cut and drill pocket holes?
The diagrams show you exactly where to place the pocket holes, so you just need to cut and drill!
Step 1: Determine pocket hole placement
I find it is easiest to mark all of your pieces first, so you can drill all of your pocket holes at one time. This is especially useful when you have a lot of pocket holes to drill, as it cuts down on time.
Step 2: Determine screw size
See my tips below for which screw you need to use. The Kreg screws are self-tapping so they won’t split the wood and eliminates the need to pre-drill holes.
Step 3: Set Drill Guide Height
This setting is on your actual jig. You will set this setting to the thickness of the thinnest board you are joining. Lock this in place before moving on.
Step 4: Set Drill Bit Depth Collar
This will control the depth of the hole you drill into your piece. Align the step collar on the bit to the guide on your jig that matches your wood thickness. Tighten the collar with the provided allen wrench.
Step 5: Drill your pocket hole
Using one of the three drill bit guides of your choice, plunge your drill until you reach the depth collar. Place the pocket holes 6-8 inches apart if you are joining long pieces together. Two pocket holes are generally needed so your piece doesn’t twist.
Step 6: Attach the pieces with screws in the pocket hole
Use the screws that you chose (tips below), along with the provided drill bit and clamps to secure the screws within the pocket hole. Glue is optional, although it will make your joint much stronger.
What is the back of a pocket hole jig?
The back of the pocket hole jig is designed to hold all the accessories that come with it! There is a place for the drill bit (with the collar attached), the 6″ and 3″ driver bits, and the material thickness gauge.
What size hose to use for Kreg 720?
Also included with the the Kreg 720 jig is a dust adapter to allow you to connect the dust collection to any sized hose from 1 1/4″ and 1 7/8″ to 2 1/2″.
What is the tool called for measuring pocket holes?
With the jig comes a handy little blue tool called the material thickness gauge. On the side it has markings to help you quickly measure the thickness of you material to get the perfect pocket holes everytime.
What clamping technology does the Kreg 720 have?
Instead the 720 pocket hole jig has Automaxx ™ clamping. This is the same clamping technology that Kreg has in their face frame clamp and corner clamp that I love.
How to measure thickness of drill bit?
Snap the drill bit into the onboard storage, then loosen the stop collar with the hex wrench on the side of the material thickness gauge and slide it to correspond to the actual thickness of your material.
What is the back of a jig?
Another new feature is one you didn’t know you needed until you had it. The back of the jig, where the board rests while you drill your pocket holes, is lined with a GripMaxx ™ anti-slip pad.
How to cut plugs out of wood?
Use the plug cutter to cut plugs out of the same wood you are building your project from. Make sure it is cut in the same direction to the grain as your pocket holes are drilled.
