Lighting a Gas Water Heater
- 1 Open the access panel covering the pilot light. ...
- 2 Switch the gas valve off. ...
- 3 Set the temperature control valve to the lowest setting. ...
- 4 Turn the gas valve to the “Pilot” position. ...
- 5 Use a long lighter to light the pilot light. ...
- 6 Reset the temperature setting and turn the gas back on. ...
- 7 Close the access panel. ...
Which boiler is right for your home?
What are the different types of boilers?
- Conventional boilers. A conventional boiler is able to heat water up and store it in a hot water tank, keeping it warm for hours until it is needed.
- Combi-boilers. Combination boilers, commonly known as combi boilers, are the most popular boiler choice in the UK. ...
- System boilers. ...
How do you turn on a boiler?
- Check all valves and place in their startup position.
- Open the sight gauge and water column high- and low-water shut-off valves.
- Close the bottom blowdown valves, then open the upper drum vent valves.
- Start filling with soft water.
What boiler should I buy?
You should buy one that is sealed combustion because it brings outside air into the burner and directs exhaust gases outside. Non-sealed combustion boilers draw heated air in and then send it up the chimney, wasting the energy used to heat the air.
How do I switch on my boiler?
- For example, if you want your boiler to turn on from 7-8 AM, then set the 4 pins between 7 and 8 to the “On” position.
- Some programmers may have you move the pin away from the center of the dial while others will make you push the pin toward the center. ...
- You can choose to set your boiler to turn on and off multiple times throughout the day.
How to know if boiler is automatic?
How to remove boiler access panel?
What to do if you still smell gas after venting?
How to get gas smell out of a room?
How to light a blue flame in a fireplace?
Where is the pilot light located on a gas engine?
How to tell if a gas ignition is automatic?
See 4 more
About this website
How do I light the pilot on my boiler?
1:523:32Furnace - How to Relight a Pilot Light | Repair and Replace - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst set the gas valve to the pilot. Position hold down the bypass button to let gas into the pilotMoreFirst set the gas valve to the pilot. Position hold down the bypass button to let gas into the pilot. Keep holding the button and use a barbecue lighter to insert a flame over the pilot.
How do I start my boiler?
The following list suggests a typical starting sequence:operating controls closed.interlocks (safety controls) closed.start fans and purge the boiler.purge requirements met.energize igniter.prove ignition flame within 10 seconds.energize main fuel valve(s)establish and monitor main flame.More items...
Can you light a boiler manually?
There are two types of boiler pilot lights. One is a manual type that you must light, and the other is an automatic pilot ignition type that lights itself. Before lighting any boiler, you must know which type you have; there are two ways to determine this.
Is it safe to relight a boiler?
For systems with an ignition switch, simply press it and wait for the boiler to start. For other systems you need to follow a few more steps. As long as there is no gas leak or damaged parts on the boiler, there is no need to call a professional.
Why is my boiler not igniting?
If the boiler is not igniting, there is a possibility the valve is blocked, seized or there is damage in the wired connections. No Pilot Light: When the boiler is not igniting and the pilot light has gone out, this usually means debris has blocked the jet.
Why won't my boiler fire up?
If your boiler does not have enough pressure, it will be unable to fire up. Check the water pressure gauge on your boiler; this should be set around 1-2. All boilers lose pressure over time, but a sudden drop indicates that the system has a leak or that the radiators need bleeding.
How do I know if my boiler pilot light is out?
The most obvious sign of the failure of a pilot light will be a lack of hot water or warm air since the burner assembly can't light and do its job of heating these substances. In many systems, a broken pilot light will prevent the appliance from working at all.
Does a boiler have a pilot light?
The pilot light is an essential part of the boiler system flame that is responsible for igniting the gas that is provided to the boiler, allowing it to heat up your home and deliver warm water to your taps.
What happens if pilot light goes out?
Can a Pilot Light Outage Be Dangerous? The worry here is that when a pilot goes out, the gas valve that supplies the fuel for the pilot flame could still be pumping gas. This can mean a buildup of gas, and when the pilot is relit or relights itself it could result in a very serious explosion.
Can I relight the pilot light by myself?
Relight the pilot light. Turn the knob to “Pilot,” and let gas to flow to the pilot. Light a lighter or match, then push in the reset button. Hold your flame to the pilot light's opening. Keep the reset switch depressed until the pilot light is burning steadily.
How do you start a gas boiler?
Check the thermostat(s) and valves, then set the thermostat(s) to low. Turn the control switch on the boiler to the "On" position. This will activate the control valves for the steam or boiler water and the thermostat(s). Verify that these are working properly.
How do you reset the pilot light?
Hold down the reset button and relight the pilot at the same time. To safely do this, you'll need to use a long-stemmed lighter and hold the end of it very close to the pilot. Once the flame catches, release the reset button. Watch the pilot light on your furnace for a few minutes to ensure it stays lit.
What to do before turning on a boiler?
Start-Up Checklist for BoilersThe boiler will be drained and flushed. ... The fuel burning equipment will be cleaned and adjusted.All controls and fuel safety shutoff valves will be looked at to ensure they're working safely and properly.The mechanical components will be lubricated.More items...
How do I know if my boiler is working?
Check the Pressure Usually, there is a pressure gauge or dial with 1-4 bars displayed. When it is cold, the pressure should be at 1 bar. If the pressure goes any lower than 1 bar, this may cause your boiler to stop working.
How do you start a cold boiler?
Begin warming the boiler slowly, allowing for gradual expansion. Open the (automatic) non-return and main steam stop valves. Open all drain valves in the system to allow condensate to exit the piping before steam fills the system.
How do I turn on my boiler for the winter?
In order to ensure that your boiler or heat exchanger is ready for the cooler weather, follow these tips to prepare your boiler for winter.Regular Service. ... Turn it on. ... Bleed it out. ... Check for warning signs. ... Open flame. ... Let your boiler breathe. ... Insulate the pipes. ... Watch out for silent killers.
The pilot light won't ignite on my boiler -- what I should check?
I've never had a boiler, so I'm not sure if this will help, but my furnace's pilot light kept shutting off after it tried to start up. I ended up having to clean the flame sensor, which is a metal bar that sticks into the middle of the pilot light.
The pilot light has gone out on my ideal classic boiler and… - JustAnswer
Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts.
Boiler Pilot Light Won't Stay Lit (How To Fix) - iHeat
Boiler Pilot Light Won't Stay Lit. If you own an older boiler, you might be familiar with the pilot light. The pilot light is an essential part of the boiler system flame that is responsible for igniting the gas that is provided to the boiler, allowing it to heat up your home and deliver warm water to your taps.
How to adjust room temperature on a boiler?
Use the screws you removed earlier if applicable. Turn on the current to the boiler at the breaker box and then turn on the boiler power. Adjust your room temperature as desired.
How to turn off the boiler?
Set the temperature in the room to the lowest setting available. Shut off the boiler using its switch. Then turn off the electrical current to the boiler at the breaker box.
How to get gas out of a boiler?
Use only your hand and do not try to force the knob to move. Leave the boiler off for five minutes to give the gas time to clear out. Walk around the area sniffing for the smell of gas. Smell the floor around the boiler. Stop, open the door, walk out of the house and seek immediate assistance if you smell gas.
Why does my pilot light go out?
A pilot light, the flame that burns below a gas boiler, rarely goes out. When it does, the problem is often traced to a malfunctioning sensor, called a thermocouple, or from a strong downdraft from your roof. Once you check and repair these issues, then relight the pilot.
Where is the pilot on a gas stove?
Follow the aluminum tube down to the pilot burner. Locate the pilot on the left side of the burner.
Can you light a boiler if it smells?
Do not light the boiler if any part has been submersed in water. Never light the boiler or touch electrical switches if you detect even the faintest smell of gas. Call the fire department if you smell gas.
What to do if your gas boiler light goes out?
If you can smell any gas in the air and your light has gone out, you might have a leak in the pipes leading to your boiler. If there is even a chance that you have a gas leak, immediately call your gas supplier, open the windows near the boiler, and leave the house.
Can a gas boiler pilot light go out?
It’s extremely rare for a modern gas- boiler pilot light to go out by itself. However, older combination boilers, which can be found in rented apartments or antique homes, can go out. If you have a modern pilot light that’s gone out, you should contact a professional to relight it . But, if you have an older gas-boiler pilot light, you can relight it with these simple steps.
Can you relight a boiler?
Warning: Do not attempt to relight a modern boiler. If you attempt to light the boiler while there is still gas in the pilot-light pocket, you face the risk of an explosion. Call a professional or your gas company to relight this type of boiler. In addition, some gas-boiler regulations prohibit renters from altering their boilers in any way. Check with your gas company before continuing with this project.
How to know if boiler is automatic?
Before lighting any boiler, you must know which type you have; there are two ways to determine this. An automatic ignition type will have a safety label on the front of the boiler that tells you that it is an automatic ignition system. If there is no label, look at the top of the gas control knob. If the control knob has two settings, on ...
How to remove boiler access panel?
Remove the access panel either by turning finger screws or lifting it up and pulling it away, if it is held on by gravity clips.
What to do if you still smell gas after venting?
If you still smell gas after venting the area where the boiler resides, turn off the gas and call in a service technician. Do not attempt to light the pilot light until the problem is resolved.
How to get gas smell out of a room?
Turn the gas control knob to the "on" position once the room has been sufficiently vented and there is no more gas smell. Flip the electrical switch or the breaker to the "on" position.
How to light a blue flame in a fireplace?
Insert a lit fireplace match or a butane candle lighter into the access hole and light the pilot light. Keep holding down the control knob button as you do this. When the flame from the match or candle lighter reaches the pilot light, a blue flame will suddenly appear. When you see the blue flame, remove the match or the candle lighter.
Where is the pilot light located on a gas engine?
Remove the access panel to gain access to the pilot light. In most cases, this panel is located adjacent to the gas control knob box. It may be attached with finger screws that are turned out, or it may be held on with gravity clips so that the panel can be lifted off.
How to tell if a gas ignition is automatic?
If there is no label, look at the top of the gas control knob. If the control knob has two settings, on and off, it is an automatic ignition system. A manual ignition will have three settings -- on, off and pilot. Never attempt to light an automatic ignition system manually.
