Lighting your pilot
- Make sure your main gas supply is ON.
- From OFF position, turn gas control knob (reads OFF, ON & PILOT) counterclockwise to PILOT position.
- Push in knob (this releases the gas to the pilot area only).
- With control knob in, push the piezo ignitor in continuously until pilot ignites (every 3-5 seconds).
- Once pilot flame is lit*, keep knob pushed in for 60 seconds.
- Make sure your main gas supply is ON.
- From OFF position, turn gas control knob (reads OFF, ON & PILOT) counterclockwise to PILOT position.
- Push in knob (this releases the gas to the pilot area only).
- With control knob in, push the piezo ignitor in continuously until pilot ignites (every 3-5 seconds).
How to light the pilot on a gas fireplace?
- Turn the knob from the “Off” to the “Pilot” position.
- Push in the pilot knob, which manually sends gas into the system.
- Push the igniter button once every second until it lights. ...
- After the pilot lights, keep the pilot button held down about 15 to 30 seconds to warm up the thermocouple and ensure that the flame stays lit. ...
- Release the pilot knob. ...
How do you light a gas furnace pilot?
How to Relight the Standing Pilot Light
- Turn off the Gas. Turn your thermostat to 80 degrees or to a setting that will demand heat. ...
- Find the Pilot Tube. ...
- Set Gas Valve to "on" Once the pilot stays lit, slowly release the button or knob and then turn the gas cock or knob from the "pilot" position to the ...
How to light the pilot light on a gas heater?
How to Light a Water Heater Pilot Light. Open the door/cover over the pilot light access. Use a flashlight or a headlamp to find the burner inside. Turn the gas knob to “Pilot,” press and hold it down. While still holding the gas down, light that pilot. When the flame ignites, continue to hold the gas knob or button down for a full minute.
How to clean a pilot light on gas fireplace?
- Turn off the fireplace gas valve and remove the front panel from the fireplace.
- Find the thermocouple, which is located next to the pilot light and looks like a small straight pipe.
- Use a can of compressed air to gently blow away any dust and dirt from the thermocouple.
What to do if remote receiver is flashing red light?
Why is my remote light flashing on my fireplace?
What is the number to call Specialty Gas House?
How long to wait to push piezo ignitor?
How do I light the pilot on my gas log fireplace?
Turn the knob from the “Off” to the “Pilot” position. Push in the pilot knob, which manually sends gas into the system. Push the igniter button once every second until it lights. Depending on how long it's been since the gas fireplace was last used, ignition may take multiple attempts.
How do you manually ignite gas logs?
0:401:40How to Manually Light a Gas Fireplace - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what I'm going to do is. Light this match. And place it as deep into the fireplace. Keep a coupleMoreSo what I'm going to do is. Light this match. And place it as deep into the fireplace. Keep a couple of matches. As. I can where I know the gas is going to move over the lighter alright it's burning.
Why won't my pilot light light on my gas fireplace?
Check Your Igniter and Thermocouple If nothing is blocking the tubing, and gas is flowing out, there might be something wrong with the spark igniter and thermocouple. Make sure there's no debris lodged between the two. If the pilot light ignites but doesn't stay lit, you might need to replace the igniter.
Do gas logs have a pilot light?
It is important to remember that not all gas fireplaces have “standing” pilot light, or, a pilot light that is “always on”. The best way to determine if you have this type of gas fireplace is to look at the control knob of the fireplace. On a fireplace you will normally find the control knob behind the grate or door.
Can a gas fireplace be lit manually?
Some gas fireplaces come with electronic ignition wall switches, which are easy to use. Just turn the On button, and the pilot should startup; if not, you will have to light the pilot manually.
What happens when pilot light goes on gas logs?
The pilot light needs to run continuously because, without it, the gas going into the fireplace would not have an ignition point. This would lead to fireplaces or entire gas fireplace inserts filling up with gas when they are turned on.
What causes a pilot light to not light?
4 Common Reasons Your Furnace Pilot Won't Light There are several reasons why your gas furnace pilot won't light: an ongoing draft, a faulty thermocouple, an accumulation of dirt, or an inefficient supply.
Do you need electricity to light the pilot light on a gas fireplace?
If the gas fireplace has a blower or fan, it will need electricity, but you should still be able to generate heat without it. If your gas fireplace has an energy-saving, alternating pilot ignition system, it will need electricity to trigger the pilot flame every time the fireplace is used.
How do you light a pilot light that won't light?
You need to turn the valve to the off position for at least three minutes. Once you have had the valve at off for a few minutes, switch it over to pilot setting. You will need a match that is lit. Hold it to the pilot opening and push the reset button on your pilot control.
What does a pilot light look like?
Inspecting a Gas Furnace Pilot Light Flame A natural gas flame should be a bright blue color with a small amount of yellow at the very tip. A propane flame will have more of a bluish-green flame with a tinge of yellow at the tip. The flame should strong enough to cover about 1/2 inch at the end of the thermocouple tip.
Do I need to turn gas off if pilot light goes out?
If the pilot light of an appliance goes out, turn off the gas at the appliance for several minutes before attempting to re-light it. Instructions should be attached to the appliance.
Is there always a flame in a gas fireplace?
Do Gas Fireplaces Always Have A Flame? Gas fireplaces that use a standing pilot ignition system will have a pilot flame that's always on. Gas fireplaces that use an intermittent pilot ignition system won't have and/or require a flame that's always on as the pilot can be switched on and off as required.
How do you light a gas fireplace by hand?
How to Operate a Gas FireplaceLook over the user manual included with your fireplace. ... Remove your fireplace's outer cover. ... Put a fireplace key into the device's gas valve knob. ... Hold a long lighter up to the burner and ignite it. ... Turn the gas key. ... Replace the fireplace's outer cover immediately.
How do you start a propane fireplace manually?
0:452:39How To Light Pilot Light On Gas or Propane Fireplace.m4v - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou may have to depress the button slightly to turn it. Then we push the same button in and hold itMoreYou may have to depress the button slightly to turn it. Then we push the same button in and hold it in while holding it we press the igniter button several times look inside the fireplace.
How do you turn a gas fireplace on without a remote?
Today's modern gas fireplaces are typically controlled with a remote control meaning starting your gas fireplace is as easy as pressing the 'on' button on your remote. Without a remote there will typically be an ignition button on the control panel of the fireplace.
Why won't my gas logs turn on?
If gas is coming out of the pilot but it still won't light, the spark igniter could be the problem. You should clear out any debris between the igniter and thermocouple. Blowing compressed air into the pilot area, waiting a couple minutes, then trying again could help to fix the problem.
What to do if remote receiver is flashing red light?
If red light on remote receiver is flashing then you need to replace batteries.
Why is my remote light flashing on my fireplace?
Make sure remote receiver (black box in fireplace) is in the REMOTE position. If red light on remote receiver is flashing then you need to replace batteries.
What is the number to call Specialty Gas House?
dander and the unit is not getting enough clean air to work properly. It shuts off as a safety. precaution. a) You can call Specialty Gas House at 614-261-0824 to schedule a service call. To get.
How long to wait to push piezo ignitor?
If this is the case you may need to hold. control knob in for a longer period until the air is pushed out. If you smell gas, wait 5 minutes until gas. dissipates before pushing in piezo ignitor.
Video Guide: Starting A Gas Fireplace
The pleasure of having a gas fireplace is unmeasurable ( read more about them here ). There is no need to look for dry wood, carry it home, and chop it up before placing it in the fireplace.
How to operate an electronic pilot in a gas fireplace
Turn on the gas fireplace’s supply line. Ensure the electric switch is on if you have an electronic setting that controls the unit’s temperature. Look for the control knob labeled “pilot ignite.” If you have a unit that enables you to regulate the temperature, it will have: on, off, and electronic settings. Turn it off for a few minutes.
What you should know
If the pilot tube has air in it, it’s difficult to light. However, after numerous tries, the fireplace should ignite. If you notice that the pilot light needs to be lit frequently, check the end of the tube for debris.
Conclusion
The technique for relighting the pilot on your gas-burning fireplace is determined by the type of pilot you have; electronic or flame-lit. It isn’t difficult, but it may be perplexing if you’ve never done it before. The above are steps on how to start a gas fireplace and relight the pilot.
What Is A Gas Fireplace Pilot Light?
A gas fireplace pilot light is a small part that can be found as part of the ignition system for the fireplace and creates a smaller flame that’s used to help light the main flames generated by the larger burner. This pilot flame is required every time when lighting the main burner flames in a gas fireplace.
What Happens If The Pilot Light Goes Out On A Gas Fireplace?
If the pilot light goes out on a gas fireplace the thermocouple and/or thermopile will help to shut off the gas supply. A pilot can be re-lit once it goes out but for gas fireplaces with standing pilot lights this re-lighting process may have to be undertaken after a short period of time.
What Is The Pilot Position On A Gas Fireplace?
The pilot position on a gas fireplace is the position on the fireplace controls that is used to start the pilot flame. The pilot position is typically set on the control dial with either the dial depressed and turned, or used with a separate spark button to light the pilot flame.
Does A Gas Fireplace Pilot Light Use Much Gas?
The pilot light on a gas fireplace will use much less gas compared to the main burner. For electronic ignition gas fireplaces the pilot will turn off when the main burner is turned off. Gas usage for a standing pilot lights are small but can add up over time.
Is There A Pilot Light On A Gas Fireplace?
Pilot lights are typically found inside gas fireplaces. The use of a pilot light helps to make the lighting of the main burner flames more efficient and effective. Pilot lights are a tried and tested component and have been incorporated into gas fireplaces for decades.
What happens if the pilot light doesn't stay on?
If the pilot does not stay on, you may have a defective thermocouple. Some thermocouples can be easily replaced; just make sure to purchase the correct length and fitting of the replacement thermocouple. If the pilot light flickers and then goes out, the gas pressure may be low.
How to clean a pilot tube?
You can also try cleaning the pilot tube using a can of compressed air used for dusting. Note: you MUST make sure the gas is off and there are no flames present prior to using an aerosol duster. Spray air around and into the end of the pilot tube opening and at the small air intake on the side of the pilot tube.
Can you use vent free gas logs in an enclosed room?
There are many in the industry who even resist using the vent free gas logs in any enclosed space. All of the by-products of combustion of the natural or propane gas will be trapped in the room with the vent free gas logs. Some people complain of the odors while others complain of headaches and other health problems.
Can you use a vent free gas log in a fireplace?
If you have a chimney or flue for the fireplace it is more likely you have a vented gas log, although a vent free gas log can be used as long as the damper is fully closed. Due to health concerns, possible carbon monoxide poisoning and fire hazards, do not install a vented gas log in a non-venting fireplace or other enclosure.
What to do if remote receiver is flashing red light?
If red light on remote receiver is flashing then you need to replace batteries.
Why is my remote light flashing on my fireplace?
Make sure remote receiver (black box in fireplace) is in the REMOTE position. If red light on remote receiver is flashing then you need to replace batteries.
What is the number to call Specialty Gas House?
dander and the unit is not getting enough clean air to work properly. It shuts off as a safety. precaution. a) You can call Specialty Gas House at 614-261-0824 to schedule a service call. To get.
How long to wait to push piezo ignitor?
If this is the case you may need to hold. control knob in for a longer period until the air is pushed out. If you smell gas, wait 5 minutes until gas. dissipates before pushing in piezo ignitor.
