How to Light a Rheem Water-Heater Pilot
- Rotate the gas knob on your Rheem water-heater clockwise until it is in the "Off" position.
- Rotate the water-heater temperature dial counterclockwise until it is set to the lowest temperature setting.
- Lift the outer door off of your Rheem water-heater. Rotate the gas knob counterclockwise until it is in the "Pilot" position.
- Push down the red button to the left of the gas knob. ...
- Replace your water-heater's outer door. Rotate the gas knob counterclockwise until it reads "On." Set the hot-water temperature dial to your preferred water temperature.
What are some common problems with a Rheem water heater?
- System Overload – You could be using too much hot water and overloading your hot water heater. ...
- Exhaust Blockage – Your hot water heater needs to vent pressure and air from the combustion chamber. ...
- Check the Error Code Guideline – Rheem water heaters can display a variety of error codes. ...
How to start the pilot light on my water heater?
How to Start the Pilot Light on My Water Heater
- Check the Pilot Light. First, check that the pilot light has indeed gone out by removing the access panel at the bottom of your tank water heater.
- Check for Gas Leaks. Before you attempt to relight the pilot, you should always check for a gas leak. ...
- Find an Ignition Source. ...
- Lighting the Pilot. ...
- Restarting Your Gas Water Heater. ...
How do you light the water heater pilot?
- Set the temperature control. to its lowest setting.
- Set the on-off control. to the pilot setting.
- Press the hot water heater. pilot button down and. hold it.
- While looking through the the sight glass slowly press the spark generator until you here it click. You should see a spark. from the generator and the.
How to light pilot on water heater?
- First, locate the pilot valve on the furnace. There should be posted lighting instructions on your furnace.
- Find the gas valve and turn it to the "off" position. ...
- Turn the valve to the “pilot” position.
- Press and hold the reset button.
- If the reset button fails, ignite the lighter. ...
- Once the pilot light stays lit, turn the valve to the “on” position. ...
Why won't my Rheem water heater light?
Some Rheem water heater pilot problems are easier to diagnose than others. Although a blocked gas line is one reason why the pilot light on a Rheem water heater won't light or stay lit, there are other reasons as well--some easier to correct than others. A faulty thermocouple or malfunction of the gas valve could be the culprit, ...
What is a Rheem water heater?
A common problem with Rheem water heaters is a loose thermocouple that falls slightly out of position.
How to clean a gas valve?
Turn off the gas, disconnect the pilot supply tube with a small wrench and clean it out with compressed air. If this doesn't correct the problem, you may need to clean or replace the gas valve; this is a job best done by a professional.
Can a Rheem water heater be contaminated?
The gas supply could be contaminated by water or oil that is restricting the gas flow. Contact the Rheem company if the water heater is in the first year of its warranty. They will recommend a local service technician. To order parts that are under warranty, call the phone number displayed on the front of your heater.
What to do if your water heater pilot light isn't lit?
February 13, 2020. If your hot water heater’s pilot light isn’t lit, it can be a major problem for you. To help you light your pilot light in your hot water heater quickly and easily, just follow these three easy steps: 1. Determine if Your Hot Water Heater is Automatic or Manual. The first step is to determine what type of water heater you have. ...
How to turn off gas on water heater?
If your hot water heater is a manual, grab a long lighter. After removing the metal plate covering the pilot button, scan the interior and find the pipe or pipes that lead up to the burner. Turn the pilot dial to the off position and wait 5-10 minutes for any gas to dissipate. Then, turn the pilot dial until it says the word pilot.
How to tell if a water heater is manual or automatic?
You need to know if your water heater is automatic or manual. To do this, check out the silver box that is sticking out on the side of your hot water heater. There should be a large dial that says pilot on it.
How long do you hold the pilot button down?
You’re going to hold the pilot button down for at least 30 seconds before you release it. 3. Lighting the Pilot Light on an Automatic Hot Water Heater. For an automatic hot water heater, just repeat all steps above. But this time, do not remove any plates. All you have to do is hold the pilot knob down for 30 seconds and hold ...
How to light a Rheem water heater?
A Rheem water heater pilot light needs to be lit manually using the piezo ignitor striker built into the water heater. Rotate the gas knob on your Rheem water heater c lockwise until it is in position. Rotate the water-heater temperature dial counter-clockwise until it is set to the lowest temperature setting.
Where to place access panel on water heater?
Place the access panel back onto the side of the water heater.
How to check gas line?
1. How to Make Sure Your Gas Supply is On 1 Find the shut-off valve to your gas line. 2 The shut-off valve usually is found close to your gas meter (see illustration below), which is located on the side or front of your home or main building. 3 Make sure the shut-off valve connected to your gas line is in the “ON” position. 4 If it is not in the ON position, then the problem is not with your gas line. 5 If it is in the OFF position, turn the valve to the ON position. Feel free to call your local gas company for advice.
How long to wait to let gas in water heater?
Rotate the water-heater temperature dial counter-clockwise until it is set to the lowest temperature setting. Wait five minutes to let through any gas in the water.
What does it mean when you have a gas water heater?
Either (1) the gas supply has been shut off or (2) your pilot light is out.
How to contact Tom Plumber?
Don’t worry, we can get you back to a warm shower in no time. Don’t hesitate to contact or call us at 1-Tom-Plumber (1-866-758-6237) .
What position is the shut off valve on a gas line?
Make sure the shut-off valve connected to your gas line is in the “ON” position.
How to ignite a pilot light?
With your fingers holding down the pilot button, press the spark generator button (also called the ignition control button) to ignite the pilot light.
What to use to check gas leaks in water heater?
Of course, a more practical solution is soapy water by combining a few drops of water and liquid soap.
How to purge air from gas line?
You might want to press the igniter button once every ten seconds while holding down the pilot light control button. This action should purge the air from the gas line.
How long does it take for a pilot light to turn blue?
Continue pressing the pilot light control button for about 20 to 30 seconds or until you have a steady blue flame through the observation window.
Why is it dangerous to light a water heater?
Unfortunately, high gas flow can make lighting the water heater dangerous because of the increased risk of flare-ups.
Where is the gas control assembly on a water heater?
The gas control assembly should be near the port connecting the gas line to your water heater. You might also see wiring for the electronic pilot system.
Can you light a water heater pilot light?
Lighting a water heater pilot light is not as challenging as it sounds. It also does not require any special tools to get the water heater up and running. However, there are essential requisites to getting this procedure executed splendidly and safely.