If your furnace has a pilot light, it will be controlled by a knob on the bottom of your unit. You can easily relight the pilot light by turning the knob to ‘off,’ waiting a minute, then setting it back to ‘on.’ This will stop and restart the gas flow of your furnace.
Why does my Trane furnace have a pilot light on?
Furnace manufacturers have all but phased out standing pilot ignition systems for gas furnaces, so if you have to light the pilot light on your Trane furnace, it's because the furnace is more than 20 years old.
How do you turn off the pilot on a gas furnace?
If the furnace has a power switch, you can just turn that off as an alternative. Take off the furnace cover and locate the gas valve and the gas control, which is a plastic or metal knob with three settings: "on," "off" and "pilot." You'll see three tubes coming from the bottom of the gas valve.
How do you light the pilot on a Kenmore gas range?
Hold a lit long-reach lighter over the pilot orifice until the pilot starts to burn. Continue holding in the gas control to give the thermocouple time to heat up. This usually takes 10 to 20 seconds. Release the gas control knob and verify that the pilot flame continues to burn.
Can you replace the igniter on a Trane XE60?
These ignitors can wear out quickly, but they're usually inexpensive and easy to replace. Older furnaces, such as the Trane XE60, don't have these LEDs, and if the furnace isn't producing heat, you have to visually inspect the burner to see if the pilot is on.
How do I light the pilot on my Trane furnace?
If your furnace has a pilot light, it will be controlled by a knob on the bottom of your unit. You can easily relight the pilot light by turning the knob to 'off,' waiting a minute, then setting it back to 'on. ' This will stop and restart the gas flow of your furnace.
Do Trane furnaces have pilot lights?
Furnace manufacturers have all but phased out standing pilot ignition systems for gas furnaces, so if you have to light the pilot light on your Trane furnace, it's because the furnace is more than 20 years old.
Where is the reset button on my Trane furnace?
Turn off the power and open up the control panel to access the reset buttons on these models. Next, lift the cover to the blower compartment, and you should see the reset button sitting next to the blower motor and blower wheel.
Is a Trane XR95 gas or electric?
The Trane XR95 is a single-stage gas furnace offering up to 95 percent AFUE. Available in upflow/horizontal and downflow/horizontal configurations, the 11 models in this series output from 38,000 to 104,000 BTUH.
How do I reset my Trane xr95 furnace?
All models are equipped with a manual resetting roll- out switch located near the burners. In case of flame roll-out, the switch trips automatically shutting off all flow of gas. The switch must be manually reset by pressing the red reset button on the top of the switch.
Where do I find the pilot light on my furnace?
Near the bottom of your furnace is a switch that normally says "Pilot," "On" and "Off." Find this switch and turn it to the "Off" position. Wait at least five minutes. This is important because it gives the gas time to dissipate, which is necessary to avoid possibly starting a fire.
How do you reset a Trane?
All Thermostat ModelsMAKE SURE THAT THE HVAC SYSTEM IS IDLE BEFORE PROCEEDING!Locate the switch for your thermostat in the breaker box.Flip the switch to the OFF position for 20-30 seconds.Return the switch to the ON position.The reboot process will take several minutes to complete.
Why is my Trane AC unit not turning on?
A Trane air conditioner may not turn on if there was a blown fuse or a tripped breaker. To fix this, change the burned-out fuse and reset the circuit breaker. You'll also need to inspect return grills for any stoppage that could restrict the airflow in the system.
What does a blinking red light mean on a Trane furnace?
You should never be concerned when there is a continuously blinking light. This means that your furnace is working normally. The red blinking light for your Trane XR90 furnace indicates that your unit was shut off due to a problem. Your system is currently locked out of its normal operation or ability to function.
How many BTU is a Trane xr95?
65000 BTU 95% AFUE 3.5 Ton Single-Stage Downflow and Horizontal Right 1/2 hp Natural or Propane Furnace.
Why is my Trane furnace light blinking 4 times?
Three flashes indicates a draft pressure error. Four flashes and your furnace is experiencing an open temperature limit circuit issue. If you see five flashes, a flame was sensed within your furnace that should not be present.
Why is my furnace blinking red 4 times?
This could be an indicator your flame sensor is dirty, and cleaning it should fix it. However, this could also mean there is a problem with the gas valve or ignitors. Gas can be intimidating to mess with, so it's best to call Doc Dancer.
Is vent length in the manual?
It is in the manual. Venting lengths are always put in the manual. I'm not sure what your post has to do with a 3 year old thread....
Do Trane control boards show error codes?
no, they show error codes as they should or there is a problem with the control board. I'm a trane dealer. Let it run through it's cycles and it will produce a fault code.
Trane XV95 burners not lighting
Two weeks ago, after what I thought was much research, I had a Trane XV95 furnace installed. It worked perfectly for the first week - held the temp within +/- 1/2 degree F. Then I noticed it would occasionally blow cool air for an extended period of time while the house temp dropped to 2 or 3 degrees F below the set point.
Update....
Two weeks ago, after what I thought was much research, I had a Trane XV95 furnace installed. It worked perfectly for the first week - held the temp within +/- 1/2 degree F. Then I noticed it would occasionally blow cool air for an extended period of time while the house temp dropped to 2 or 3 degrees F below the set point.
Problem resolved!
The Trane Canada rep dropped by, and quickly determined that the ventor blower was making WAY too much noise - basically running full-out whenever the furnace was running. Putting a manometer on the pressure switch showed that the open/close set points were way too close.
