Some of the Ryobi string trimmers allow the user to load without removing the knob. It’s time to insert a new line in the Ryobi string trimmer. Cut a couple of 10 feet pieces of string and double them up. Insert these lines inside one of the reel’s holes. Then, you have to pull it in towards the spool till only a few inches are remaining.
How to load a Ryobi string trimmer?
A Step-by-Step Guide to Load Ryobi String Trimmer. Step 1: Choosing the Appropriate Line. Each Ryobi trimmer has different string requirements. The best way to understand the ideal string attributes is ... Step 2: Disassembling the Trimmer Head. Step 3: Inserting the Line. Step 4: Wrapping the Line ...
How do you put a trimmer on a lawn mower spool?
Locate the hole in the top part of the spool and insert one length of trimmer line into it. Follow the arrows on the spool to wind the length of line around the spool counterclockwise. Feed the trimmer line through the exit slot, leaving approximately 6 inches of string protruding.
How do you install a string trimmer?
Measure a 9-foot length of trimmer line and cut it from the spool. Repeat the process to create a second 9-foot length for installation in the string trimmer. Locate the hole in the top part of the spool and insert one length of trimmer line into it. Follow the arrows on the spool to wind the length of line around the spool counterclockwise.
How to refill a string trimmer spool?
How to Refill a String Trimmer Spool 1 Turn off the string trimmer and then lay the trimmer down with the head facing up. 2 Remove the spool retainer on the bottom of the head by pushing in the tabs and then pulling the retainer off. 3 Lift the spool off the head and remove any remaining string. More items...
How do you rewind a string trimmer spool Ryobi?
1:232:03Ryobi String Trimmer Spool Replacement 530670001 - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow align the crank handle on the bump knob and rotate the handle clockwise while holding theMoreNow align the crank handle on the bump knob and rotate the handle clockwise while holding the trimmer head to wind the line around the spool. Keep winding until the line is within the guard assembly.
How do you insert a Ryobi trimmer line?
0:433:27How to change the trimmer line on a Ryobi 18 volt cordless string trimmerYouTubeStart of suggested clipEnd of suggested clipYou don't have to cut. It just go ahead there's a little hole as you can see here where you wind theMoreYou don't have to cut. It just go ahead there's a little hole as you can see here where you wind the line. In you want to put the line in the hole as you can see there's there's a hole here.
How do you spool a Ryobi gas trimmer?
1:314:58How to Replace Ryobi Weed Eater String | Full Crank 2 Cycle ModelYouTubeStart of suggested clipEnd of suggested clipWe can take this part off and you can see the screw cap here on the other side it has arrows. SoMoreWe can take this part off and you can see the screw cap here on the other side it has arrows. So those have to be lined up when you're loading the spool.
How do you put spool on expanded Ryobi?
1:213:33How to Restring the Ryobi Expand-It Trimmer - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe head. It might take a little bit to push it through but um it goes through so you got toMoreThe head. It might take a little bit to push it through but um it goes through so you got to remember there's a hole that goes all the way through that spool there in the middle.
How do I refill my Ryobi easy edge?
4:206:25RYOBI How to Re-Spool/Re-String 18V WEED WHACKER - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you just disconnect this and then you'll see there's a hole it's so easy just see what there's aMoreSo you just disconnect this and then you'll see there's a hole it's so easy just see what there's a hole right. There do that little hole right there. So you just take the end of the cord.
How do you put trimmer line on?
0:121:28String Trimmer Line Installation Instructions - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd remove the inner reel in spring. Find the two holes on top of the inner reel. And insert bothMoreAnd remove the inner reel in spring. Find the two holes on top of the inner reel. And insert both ends of the line into one of the holes. Pull. The line through. Until two to three inches. Remain.
How do you unlock a Ryobi trimmer head?
Grasp the shaft housing firmly with your left hand. With your right hand, wiggle the cutting head while gently pulling it upward. Continue this motion, until it slips off the large hex nut it nestles on.
How do you restring a Ryobi ss30 trimmer?
0:003:25Lawn Care & Landscaping : How to Restring a Ryobi Weed EaterYouTubeStart of suggested clipEnd of suggested clipWe need the inner. Part I've already pre-measured my line it took about a good arm's length take theMoreWe need the inner. Part I've already pre-measured my line it took about a good arm's length take the string put it to the center push it through grab it and just start pulling.
How do I change the attachment on my Ryobi?
0:030:42How To: RYOBI EXPAND-IT Attachments - YouTubeYouTubeStart of suggested clipEnd of suggested clipTurn the OneTouch coupler 180 degrees to loosen then press and hold down the attachments lock buttonMoreTurn the OneTouch coupler 180 degrees to loosen then press and hold down the attachments lock button while you slide the attachment out insert.
How do you put a Ryobi 10 string trimmer together?
2:027:56Ryobi One Trimmer: Assembly, Use & Spool Replacement for ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipPiece and a slot on the trimmer. End line up the tab and the slot push the two pieces together whileMorePiece and a slot on the trimmer. End line up the tab and the slot push the two pieces together while holding down the tabs. And snap it into place next attach the grass deflector to the trimmer.
Why does my trimmer line keep coming out?
If this cap is broken or worn out over time, it can malfunction, causing too much line to feed out when you bump it. Depending on its damage, it could be getting hung up as it tries to return, allowing the line to continuously advance. To replace it, simply remove and replace the bump cap with a new one.
Wear Safety Equipment
Dress properly and wear safety equipment to protect yourself from any kind of incident.
Types of Ryobi String Trimmer
There are two main kinds of string trimmers: gas-powered or electric trimmers. Gas string trimmers are cordless, powerful, have two-cycle engines, and need a mixture of gas and oil to work.
Step by step guide to load a Ryobi String Trimmer
After you use your Trimmer for a season of use, it will probably need some replacements. This two-line trimmer typically uses a 0.080-inch diameter monofilament trimmer replacement line.
Use of Ryobi String Trimmer
String trimmers are designed for chopping grass that’s not easily reached by a mower, like under bushes or up against walls. Always take care when trimming around small plants and flowers as they will be easily damaged.
Last Thoughts
Ryobi string trimmer is very useful to trim the grass of lawns in your home. Make sure to follow safety precautions before using a string trimmer.
Where is the arrow on a Ryobi trimmer?
You’ll notice that there’s a small arrow that is embossed on the head of the trimmer. The arrow’s location in each Ryobi trimmer is mostly the same.
How to insert string in Ryobi?
It’s time to insert a new line in the Ryobi string trimmer. Cut a couple of 10 feet pieces of string and double them up. Insert these lines inside one of the reel’s holes. Then, you have to pull it in towards the spool till only a few inches are remaining.
How to remove a trimmer head?
The next step in the process is disassembling the trimmer head. You can remove the trimmer head by unscrewing the trimmer’s bump knob. Now, pull the old line out and discard it.
How to keep reel spring from shifting?
Hold the spring firmly downwards to prevent it from shifting or moving out. Spot the eyelets on the spring’s head. While you’re equipping one hand to position the spring, use the other hand to push the line through the eyelets. Pull the string firmly, and continue holding the reel’s spring as you perform the next step.
What is the original position of a reel?
In this step, you have to return the reel to its primary position. The original position of the reel is one the shaft. You have to line the holding slots with the eyelets.
Can you use serrated line on Ryobi string trimmer?
There are multiple sizes of trimmer lines that will fit your Ryobi string trimmers. In case you have heavier, thicker weeds, you can opt for a serrated line.
Can you cut string length after loading Ryobi?
An incorrect line can lead to the engine wearing out quicker. It is ideal for checking the user manual for this purpose. You may also cut the string length after loading the Ryobi string trimmer. After loading the spool and checking the alignment, you can get back to lawn work.
How to make a spool for a trimmer?
Locate the hole in the top part of the spool and insert one length of trimmer line into it. Follow the arrows on the spool to wind the length of line around the spool counterclockwise. Feed the trimmer line through the exit slot, leaving approximately 6 inches of string protruding. Repeat the process on the bottom part of the spool until it also is filled with line.
What is Ryobi home maintenance?
Home Maintenance. By Amie Taylor. Ryobi is a well-known brand name when it comes to tools for the home and garden, manufacturing outdoor equipment like string trimmers, leaf blowers and chain saws. If you own a Ryobi string trimmer, eventually you'll have to replace the trimmer line when it runs low.
How to remove a spark plug from a spool?
Remove the spark plug wire from the spark plug to avoid accidental starts. Turn the trimmer spool counterclockwise while holding the trimmer head to remove the spool from the machine. Pull the spool from the head, ensuring that the spring remains connected to the spool.
What is Ryobi string trimmer?
Ryobi manufactures a number of gasoline-powered string trimmers, as well as a battery-powered model that is part of its One+ line of tools that operate on a common lithium-ion battery-pack. The string heads for the gasoline- and battery-powered models aren't the same. The most important difference is that the latter takes only a single 0.065-inch string while the former takes two strings that can be from 0.080 to 0.095 inches in diameter. The procedures for winding the heads are similar and shouldn't delay your trimming job for longer than about 10 minutes.
How to clean a spool on a spool?
Remove the spool, ensuring that the spring remains attached to it. Pull off any old string and clean the spool and the inside of the head with a rag.
How to make a spool of arrows?
Cut a single 9-foot length of 0.065-inch microfilament string from a roll. Feed one end into the hole in the center of the spool and wind the string in the direction of the arrow. Stop winding when 6 inches of string are left on the end.
How to turn a string head?
Hold the string head with one hand while you unscrew the spool retainer with the other. You may have to turn the head clockwise or counterclockwise; some heads have reverse threads while others don't.
How to replace a spool retainer?
Replace the spool retainer by aligning the tabs and pushing down until they lock. In order to avoid overfilling the spool, ensure that there is 1/4 inch of space between the wound string and the outside edge of the spool. Avoid using string that is too wide for your trimmer.
How to wind a string in a spool?
Insert the end of one of the lengths of string into the upper anchor hole in the hub of the spool and wind the string in the direction of the arrow on the base of the spool. Keep the string confined to the upper section of the spool and stop winding when about 6 inches of string remains.
How much space between wound string and spool?
In order to avoid overfilling the spool, ensure that there is 1/4 inch of space between the wound string and the outside edge of the spool. Avoid using string that is too wide for your trimmer. It won't advance properly, and you could overwork the trimmer engine and burn it out.
How to remove spool retainer?
Remove the spool retainer on the bottom of the head by pushing in the tabs and then pulling the retainer off.
What is a string trimmer?
String trimmers are available in both gas and electric models. A yard trimmer is a handy tool when maintaining a yard. The trimmer cuts grass and weeds in areas that a lawnmower cannot reach, such as along a fence line, around trees and against your home.
What happens when a trimmer head spins?
When the head spins, the string acts as a blade to cut anything it its path. As you use the trimmer, the string breaks, requiring more to be unwound from the spool in the head. The spool must be re-wound with new string after you have used all the string in the spool. Advertisement.
Step 1
Detach the trimmer attachment from the power unit to assure the unit will not operate while you restring the trimmer. Remove the bump knob cover to expose the inner reel. Remove the inner reel from the outer hub and discard any remaining trimmer line on the inner reel.
Step 2
Measure two 6-foot lengths of monofilament replacement line. Thread the ends of the two lines into the holes located on the inner spool and wind the cord in the direction noted by the arrows on the inner reel. Stop winding when there is 5 inches of trimmer line remaining.
Step 3
Insert the ends of the lines in the holes in the outer hub and place the inner reel in the hub. Snap the bump knob cover into place.