Bottom-Loading A Staple Gun:
- Step#1: Hold the Gun Upside Down Turn your gun upside down, and keep its back face towards you and front face away from you.
- Step#2: Press the Trigger Button You will see a magazine on the bottom with a trigger button.
- Step#3: Pull Out the Magazine ...
- Step#4: Chamber Is Released ...
- Step#5: Take the Staples ...
- Step#6: Put the Staples into the Chamber ...
- Step#7: Close the Chamber ...
Full Answer
How do you lock the trigger on a staple gun?
Unplug the staple gun and lock the trigger before you begin loading it. Pull the plug out of the wall, and find the trigger lock just behind the trigger that you would use to release a staple. Shift the lock to the left or right, or press it toward the trigger to lock the trigger in place. [10] Your gun may not have a trigger lock.
How do you load a staple gun?
1 Method 1 of 3: Rear-Loading a Manual Staple Gun. Locate the pusher rod at the back of the gun. ... 2 Method 2 of 3: Bottom-Loading an Electric Stapler. Unplug the staple gun and lock the trigger before you begin loading it. ... 3 Method 3 of 3: Loading a Pneumatic Stapler. Turn off the compressor and detach the stapler. ...
How do you test a stapler?
Test the staple gun on a piece of paper or wood. To make sure the staples are loaded properly, fold a piece of paper in half or use a scrap piece of wood or fabric. Place it under or inside of the stapler and pull the trigger to release a staple. Make sure the staples are firing smoothly with no jams. [9]
How do you use a stapler follower on a staple gun?
Release the lever at the front of the gun to move the follower into place. Unlock the follower by squeezing the lever and then releasing it. The stapler should automatically push the staples into the staple gun. If it doesn’t automatically move, give the rod small push and it should engage.
How do you load staples into a Surebonder staple gun?
0:180:58How to load the JT21CM All Purpose Staple Gun - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut both fingers in the bot on the bottom of this of the pusher run push it in and down to releaseMorePut both fingers in the bot on the bottom of this of the pusher run push it in and down to release the pusher rod take the rod. Out. Use your JT 21 staples fold them on to the rail.
How do you load an easy shot staple gun?
0:040:42How to load the TruTac Stapler - YouTubeYouTubeStart of suggested clipEnd of suggested clipToday I'll demonstrate how to load your staples. Into the arrow fastener tt 21 staple gun this toolMoreToday I'll demonstrate how to load your staples. Into the arrow fastener tt 21 staple gun this tool has a bottom load feature. So turn your tool upside.
How do you use a Surebonder light duty staple gun?
0:412:19The New 5659 Triggerfire Cable Tacker by Surebonder - YouTubeYouTubeStart of suggested clipEnd of suggested clipSqueeze the handle to load the staple. Position the stapler on the work surface. While use on theMoreSqueeze the handle to load the staple. Position the stapler on the work surface. While use on the front and rear cable guides to align the cable. Then pull the trigger to set the staple.
What staples fit a Surebonder staple gun?
441" Crown Staples (Arrow JT21 Type) can be used in Surebonder Staple Gun models 5525, 5580, and ST-3600.
How do you put staples in a stapler?
2:033:31How To Refill A Stapler-Tutorial For Putting More Staples In - YouTubeYouTubeStart of suggested clipEnd of suggested clipRight the prongs. Go down the flat side is the side that you see so as you can see right here thisMoreRight the prongs. Go down the flat side is the side that you see so as you can see right here this is all the flat. Side okay as you can see right there's all the flat side that faces.
How do you load an arrow in a electric staple gun?
0:091:33How To Load Arrow's T50ACN Electric Staple Gun and Nailer - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure the legs of the staple are facing up towards the ceiling place the strip of staples intoMoreMake sure the legs of the staple are facing up towards the ceiling place the strip of staples into the magazine. If you're nailing you'll need a strip of 5 8 inch 18 gauge brad nails.
Why is my staple gun not firing?
Jams usually occur when staples get cramped, bent, or wedged in the very top of the gun head. This makes it very difficult or even impossible for the tool to function correctly. So, if you find that your staples aren't firing properly, your device likely has a blockage.
How do you fire a staple gun?
0:233:37How to Operate a Staple Gun - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we're going to take staple gun push. The tip down. And pull it out there you go again. Hold theMoreSo we're going to take staple gun push. The tip down. And pull it out there you go again. Hold the tip down firmly squeeze. I got pretty big hands pretty big arms.
How do you use a wall stapler?
Tape the paper in place while you staple it if a friend cannot help you hold it. Push the stapler ejection gap firmly down on the part of the paper you want to tack. You will hear the staple enter the wall. Repeat this tacking process as necessary.
What size are Arrow T50 staples?
Keep your staple gun ready for use with these Arrow T50-type 1/2-inch staples.
How do you load a craftsman easy fire staple gun?
0:120:40How To Load A Bottom Load Staple Gun - YouTubeYouTubeStart of suggested clipEnd of suggested clipMy first piece of advice is turn the tool upside. Down before you load otherwise it loses tables. SoMoreMy first piece of advice is turn the tool upside. Down before you load otherwise it loses tables. So I need to load staples. Turn it to up open my latch pull magazine.
How do you load a mini stapler?
To load these plier staplers remove the magazine pusher by pressing it in and unhooking it. Place the staples, legs down, across the staple channel and slide into the chamber. Carefully reinsert the magazine pusher and press the spring home allowing you to hook it back in place.
How do you load a Surebonder 3 in 1 staple gun?
0:561:23Surebonder TriggerFire - Product Features - YouTubeYouTubeStart of suggested clipEnd of suggested clipEvery time into harder materials to load the Shahbandar trigger fire simply unlock this slide trackMoreEvery time into harder materials to load the Shahbandar trigger fire simply unlock this slide track and you can just drop the staples in to load the gun quickly.
How do you load a t50 staple gun?
0:031:04How to Load Arrow's T50 Staple Gun - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst you need to remove the pusher by pushing in and completely removing it from the tool. Then youMoreFirst you need to remove the pusher by pushing in and completely removing it from the tool. Then you take a fresh strip of arrow t-50 staples and insert them on to the guide rail.
How to rear load a staple gun?
To rear load a manual staple gun, start by locating the push rod at the back of the gun. When you're ready to release the push rod, look for a small metal rectangle with 2 indentations on the sides and a small hook on the top or the bottom. Next, push in on the rod, and pull it out to remove it.
How to test a stapler gun?
Then, place the front of the gun on a piece of wood pull the trigger to ensure that only 1 staple comes out of the gun at a time. It should fire smoothly with the staple laying flush against the wood.
What is a staple gun?
Learn more... A staple gun is a handheld machine that can force metal staples or small nail brads into heavy paper, plastic, wood, or thick fabrics. Staple guns come in manual, electric, and pneumatic models to fit a variety of needs, and they’re more powerful than the average desk stapler. Before you can use your staple gun for a woodworking, ...
How to release staples from a staple gun?
1. Unplug the staple gun and lock the trigger before you begin loading it. Pull the plug out of the wall, and find the trigger lock just behind the trigger that you would use to release a staple. Shift the lock to the left or right, or press it toward the trigger to lock the trigger in place.
What is a follower on a staple gun?
The follower is a rod that holds the magazine in place and makes sure it doesn’t move. Most pneumatic staple guns have a large one at the front of the gun, protruding from underneath the area where the staples fire out of the gun.
How to make sure staples are loaded?
To make sure the staples are loaded properly, fold a piece of paper in half or use a scrap piece of wood or fabric. Place it under or inside of the stapler and pull the trigger to release a staple. Make sure the staples are firing smoothly with no jams.
How to release a pusher rod?
1. Locate the pusher rod at the back of the gun. Point the gun so that the area where the nails come out of is facing away from you. Then, look at the back of the gun for a small metal rectangle with 2 indentations on the sides and a small hook at the top or bottom. This is the release for the pusher rod.