How to make a compact smoke machine for cosplay (for under $30!)
- Things You’ll Need. A Kanger EVOD Bottom Coil Clearomizer. I got mine from Vapeking, here in Australia, and their shipping times were phenomenal.
- Making the Smoke Machines. Assuming you have everything, the first step is to solder cables to your eGo Battery Connectors. ...
- Notes on using your smoke machines. These get VERY warm. ...
How to make a Homemade Smoker?
Step By Step Guide
- Gather the Materials. Determine your materials. ...
- Prepare the Site. Once you have your materials, it is important to find a flat surface that can be used as the firebox and smoking chamber foundation site.
- Build the Smoker. Start by building a brick wall on one end of the firebox. ...
- Setup the Chimney. ...
- Build the Smoker’s Chamber. ...
- Grate Setup. ...
- Smoker Placement. ...
How to make a homemade EVAP smoke test machine?
- Measure the diameter of the metal shaft of your soldering iron. ...
- After getting the right measurement, take note of it and drill a hole with the exact size dead center on the lid of the pickle jar. ...
- If your soldering iron has a metal base or a metal cap around the bottom of its handle where it meets the shaft, you will have to make a shroud ...
How to make a smoke machine?
Making the Smoke Machines. Assuming you have everything, the first step is to solder cables to your eGo Battery Connectors. Cut off two lengths of wire – black and red – around 20cm long. You’ll cut it to length later. Solder the positive (+, red) lead to the center of your connector, as per this photo.
What is the best automotive smoke machine?
“ AutoLine Pro leak detector is the best smoke machine considering from all good aspects. Its built quality, functions, operating system, and versatile features are amazing to detect a fuel leakage within minutes. In addition, this machine is best from the price and customer rating aspects”
How can I make a cheap fog machine?
0:152:345 Dollar Fog Machine - YouTubeYouTubeStart of suggested clipEnd of suggested clipNice and easy grab some food grade glycerine from your local supermarket as well as some distilledMoreNice and easy grab some food grade glycerine from your local supermarket as well as some distilled water which is basically just purified. Water you're going to need a glass as well.
How do you make fake smoke at home?
Fill a metal or plastic container half full of hot water and add a few pieces of dry ice every 5-10 minutes. As the water cools, you will need to add more hot water to maintain the fog effect. As a rule of thumb, one pound of dry ice will create 2-3 minutes of fog effect.
How do you make a smoke dispenser?
0:074:36How to Make a Smoke Machine | DIY Smoke Machine | dArtofScienceYouTubeStart of suggested clipEnd of suggested clipAnd I'm sure all of you also want to make a smoke machine when I wanted to make a smoke. Machine IMoreAnd I'm sure all of you also want to make a smoke machine when I wanted to make a smoke. Machine I checked out many videos. And I wanted to make the fluid base one with water and glycerin.
How do you make a small fog machine?
2:474:38How to make a mini fog machine - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you have your candles all wax down or your duct tape. Whatever you did you can go ahead andMoreOnce you have your candles all wax down or your duct tape. Whatever you did you can go ahead and light them and then put your candle thing on the jar over it.
How do you make a fake fog machine?
In a glass, mix together one part glycerin and three parts distilled water. Stir completely with a spoon. The water should be murky initially but will clear up immediately after stirring. This is your "fog juice."
How do you make homemade fog machine liquid?
0:041:50Easiest Way to make your own Fog Liquid or Fog Juice - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhich means we're going to use 3 parts water to one part glycerin. So I'm just going to pour 3/4. OfMoreWhich means we're going to use 3 parts water to one part glycerin. So I'm just going to pour 3/4. Of a cup of water into this measuring cup. And then we're just gonna top it off to the 1 cup mark.
What can I make a smoker out of?
0:002:43How to Make a Meat Smoker with a Trash Can - Better Bacon BookYouTubeStart of suggested clipEnd of suggested clipThe first one is obviously the trashcan itself. And then you need to get a grate that will fitMoreThe first one is obviously the trashcan itself. And then you need to get a grate that will fit inside the trashcan.
How do you make a automatic smoker?
2:247:13BEST automotive smoke machine you can build - YouTubeYouTubeStart of suggested clipEnd of suggested clipNice and snug now cut a little piece of the bic pin off. And then clip off the end of the bic penMoreNice and snug now cut a little piece of the bic pin off. And then clip off the end of the bic pen lid to make a tapered tube. So the smoke can go through it now you can cut off the plastic protrusion.
How do you make a mist maker?
1:206:07How to make MIST MAKER at home | DIY mist maker - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd this vibration will create tiny droplets thus the mist so let's start building first we need icMoreAnd this vibration will create tiny droplets thus the mist so let's start building first we need ic triple five a ir officer 44 mosfet a 220 micro entry inductor.
How do you make a dry ice machine?
1:473:05How to make a Dry-Ice Powered Mini Fog Machine - YouTubeYouTubeStart of suggested clipEnd of suggested clipPlace the dry ice into the mini fog machine and replace the lid with the fan on and blowing air intoMorePlace the dry ice into the mini fog machine and replace the lid with the fan on and blowing air into the machine lots of fog should immediately begin blowing from the outlet pipe.
Step 3: Insert the Syringe Needle in the Copper Pipe
Now take a Syringe Needle insert the Syringe needle in the Copper Pipe.Use a Thin Syringe needle which will easily go into your copper pipe.
Step 4: Attach the Oxygen Pipe to the Copper Winding
1) Once you insert the Needle Insert then insert thin Oxygen Pipe ( This can be easily be bought from any Aquarium shop) Into the other End of the Needle And secure it with Epoxy Putty to avoid any leakages.
Step 5: Placing the Iron (s)
1) cut out small Plywood pieces on which you can place & stick the soldering iron . This is to make sure that there is a gap between the surface and the hot part.
Step 6: The Smoke Machine Liquid
1) You can get this from any store which sell Lightings for parties.Or you can Make smoke juice at home by just using Glycerine (Get it from Medical store) & Distilled Water ( Buy it from any car & bike Battery Shop) then Mix 1/4 glycerine & 3/4 Distilled water.
Step 7: Make a Box Enclosure for the Iron
1) Make a small Box Enclosure for the soldering iron.I used My Old Box of the Laser Projector.The Soldering Iron Will be Extremely Hot so mak a box enclosure using ply wood with a opening so that the smoke can go out
Step 8: Testing Time
Connect the Soldering irons to the Mains and then wait until 4 mins then Use the pump to get the smoke into the copper winding and then see the smoke effect.
Step 1: Vapor Liquid
While you can use standard vapor liquid that is designed for e-cigarettes for this project it is not recommended as most of it contains two things that we don't need: nicotine and flavoring. Most vape shops either have or can mix up the liquid without flavoring or nicotine. It can also be purchased in this form from eBay.
Step 2: Safety
The vapor emitted from e-cigarettes, including the one shown here, can set off smoke detectors. While such occurrences seem to be infrequent please use care when using the smoke generator in public buildings.The e-cigarette has a heating element that vaporizes the liquid.
Step 3: Choosing an E-Cigarette
I started out using a very inexpensive e-cigarette that I purchased on eBay. The unit shown here included two cigarettes, batteries and a charger.
Step 4: You Need Only the Heating Unit
Since I have been disassembling the e-cigarettes to harvest the heating element I spent some time searching eBay for a seller that might be offering just that component. Luckily I found such a vendor and purchased 5 heating elements (shown here) for less than $8 delivered. They are available in several types with varying resistance.
Step 6: Soldering the Heating Element
Two wires need to be soldered to the end of the heating element. I used thin (26 or 28 gauge or so) stranded wire. One wire goes to the body of the unit and the other to the central portion of it.
Step 7: ... More Soldering
Be very careful not to plug up the hole that is in the middle of the central shaft. That hole is how air gets to the heating element. The hole is shown by the arrow in the photos below.
Step 8: Cutting the Pill Bottle
First cut the pill bottle in half being careful to keep the cut even and parallel to the top of the bottle. I used a piece of wire wrapped around the bottle to help mark the cut line.
DIY Smoke Machine for Vacuum or EVAP Leaks: What is an EVAP Smoke Test?
The evaporative emission control system or EVAP is an important component of a vehicle since it is the one that keeps gas fumes in the fuel tank from getting in the atmosphere. It is crucial that your EVAP system is always at its best condition.
DIY Smoke Machine for Vacuum or EVAP Leaks: How Do You Make a Car Smoke Machine?
Performing a smoke leak test might be one of the most effective methods in determining the exact location of a vacuum or EVAP leaks, but purchasing an expensive smoke machine to perform it might just be too much for many car owners.
