How do you make a closet rod?
- Step 1: Cut Dowel to Desired Length. You can have it cut at the hardware store or use a miter box and saw)
- Step 2: Install Eye Hooks. Drill pilot holes and put in eye screws at each end of the dowel (these will be used to hang the dowel). …
- Step 3: Attach Chain. …
- Step 4: Hang Your Stuff!
Full Answer
How to build a closet hanging rod?
Steps
- Size the Shelves. Measure and mark the width of the Shelf on a piece of ¾-inch plywood. ...
- Sand the Shelves. In preparation for assembly, sand the surface and edges of each Shelf smooth, and remove any burrs along the edges left by the saw.
- Mark the Shelves and 1 x 2. ...
- Attach the 1 x 2’s. ...
- Mark the Walls. ...
- Begin Drilling the Shelf Pin Holes. ...
How to install a closet valet rod?
Part 2 Part 2 of 3: Positioning the Rod Correctly Download Article
- Choose an appropriate height for the rod. In order to make the closet rod truly helpful, put it at a height that makes it accessible and useful.
- Decide how deep you want the bar to be. It's important to have it back far enough so that the hangers and clothes that are on the bar will ...
- Mark both sides of the closet. ...
How to make DIY curtain rods?
Instructions
- Cut the electrical conduit to length. ...
- If you choose to paint your curtain rods, it is easiest to paint each of the pieces before assembling the DIY curtain rod brackets. ...
- Once the primer is fully dry, paint each component with a few thin coats of your chosen spray paint.
- Align the hold of each one-hole strap with the last hole of each corner bracket. ...
How to build cheap and easy DIY closet shelves?
Supplies for DIY closet shelves
- A sheet of MDF cut into 14” strips – My cubbies are 14” deep but you can use whatever measurement works best for you based on your closet size. ...
- 1″x2″ pine boards to create the side shelf supports (two 14” pieces for each shelf)
- 1″x2″ poplar or pine boards to create a nice thick facing for each shelf (amount depends on size of your closet and shelves)
How to measure a closet rod?
What happens if you cut a closet rod too short?
How deep should a closet bar be?
What are the different types of closet bars?
How tall should a rod be?
How to check for screws in studs?
Do you need to add wood supports to a closet?
See 4 more
About this website
How do you build a closet hanging rod?
DIY Hanging Closet RodStep 1: Cut Dowel to Desired Length. You can have it cut at the hardware store or use a miter box and saw)Step 2: Install Eye Hooks. Drill pilot holes and put in eye screws at each end of the dowel (these will be used to hang the dowel). ... Step 3: Attach Chain. ... Step 4: Hang Your Stuff!
Can I use a curtain rod as a closet rod?
This drapery rod turned closet rod is such a great solution for those “unusable” closet walls or really for any place you need clothing storage but are short on space. Have you ever thought to use to a drapery rod for something other than hanging curtains? I've also used them to organize ties and hats.
What makes a good closet rod?
Steel closet rods are the strongest option of all because the material is very resilient and steel springs back to the original shape even if overloaded. These rods usually have a chrome-plated exterior. Stainless steel closet rods act much similar to the steel ones.
What size dowel is used for a closet rod?
One of the most common uses for wooden dowels is turning them into closet rods. To do this, simply go to any Home Depot and make your way to the moulding aisle. There you will find several Woodgrain Crafters Dowel options to choose from, but you should preferably go for one that's 1 ¼ inch in diameter.
How much weight can a curtain rod handle?
A tension rod can hold between 10-45 pounds, depending on its material. However, the average tension rod can handle about 20 pounds. Whether you want to suspend curtains or clothes, a tension rod makes an excellent addition to your home.
Can I make my own curtain rod?
Curtain rods are one of my favorite things to DIY. Outfitting all of your windows with nice curtain rods can get very expensive, very quickly. Luckily, it's really easy to make your own curtain rods using inexpensive items from your local home improvement store.
Is wood or metal better for closet rod?
The Standard Oval Closet Rod Standard oval closet rod in polished chrome. All closet rods for custom closet organizers are made of sturdy metal rather than wood or wire that is coated in various finishes. The higher quality metal rods hold a lot of weight and won't sag.
How far can a closet rod span without support?
A wood closet rod can long for a maximum of 48 inches (4 feet) without support. If the wood closet rod is longer than 48 inches, it requires support.
What is standard height for closet rod?
60-inchesA typical closet can include two levels of hanging rods. As a rule, place the top rod 80 to 82-inches up from the floor and the bottom rod about 40-inches up from the floor. For a single rod application, plan 60-inches from the floor for placement.
What type of wood is usually used to make dowel rod?
Wooden dowels are generally made with hardwood such as beech and poplar, which makes them reliably strong. We've scoured the market to find the best dowel rods of various lengths and diameters; check out our recommendations below.
What type of closet rod is the strongest?
Closet rods made from steel are chrome plated. In addition to being the strongest, they are also very resilient. Even after being overloaded they are likely to spring back to their original shape due to the resilient quality of steel. Stainless Steel is the next strongest material.
What diameter is a closet rod?
A106 premium closet rod is made of quality steel and is available in several different architectural finishes. Outside diameter is 1-5/16”. Rods are available in 6 and 8 foot lengths.
What can I use an old curtain rod for?
Curtain rods can also be utilized in the kitchen to act as utensil rods. Fix them above the stove, the sink or underneath upper cabinets and use S-hooks or rings with clips to hang utensils from. You can even use curtain rods to create a suspended pot rack, or butcher's rack, over a table or central island.
Will a shower curtain rod hold clothes?
Of course, they can! Tension rods generally work better in children's rooms, since their laundry doesn't weigh as much as those of adults. You can use them as an alternative spot to hang their clothes by placing the rod's ends on opposite walls inside their closet.
How to Make Two Levels of Hanging Rods in a Closet
Hold each pole up so that its ends touch the height markers you made and use a level to make sure it is not crooked. Trace a circle around the points of contact on the wall.
How far down should I put closet rods?
The hardware for the closet rods should be positioned about 1-1/2 to 2 in. down from the shelf above and about 10 to 12 in. from the back wall.
What can I put in a deep closet?
Deep closets can fit double rods mounted parallel to each other in the front and the back. It’s an ideal setup for tightly stashing off-season outfits. Add a rolling bin on the closet floor to store accessories, beachwear or ski gloves in Ziploc Big Bags. This will keep your bedroom closet clear and your active gear at hand.
How many teeth do you need to cut out a closet baseboard?
Also, for smoother cuts, use a sharp blade with at least 40 teeth. You don’t have to cut out the baseboard in the closet or even trim the back side of the dividers to fit its exact profile. The back of the organizer will be mostly out of sight, so square notches will do (Photo 2).
Why are the inside walls of a closet not square?
The inside walls of the closet will never be perfectly square because of the mudding and taping of the drywall corners. Measure your closet width and cut your shelf to the widest dimension, then tilt the shelf into position. At the corners, mark a trim line along each end to achieve a snug fit (Photo 7).
How to cut notches for baseboard?
Use a jigsaw to cut notches for your baseboard so the vertical dividers will fit over it.
How to secure side shelves?
To best secure the side shelves, sand the cut edge that will be in contact with the center unit with 100-grit paper. This will break up any finishing oil and provide a cleaner surface for the glue. Lay out the remaining shelves on their side wall hook strips and use a level to determine their exact position on the center unit.
How to keep glue from smearing on shelves?
To prevent smearing, put the center unit side in first while tipping up the wall side of the shelf. Keep a cloth handy to wipe up the inevitable glue smudges.
How to measure a closet rod?
Before you purchase your closet rod, you need to know how long it has to be. Every closet varies, so it's important to measure the width of your specific closet with a tape measure so you can purchase the correct length.
What happens if you cut a closet rod too short?
If you accidentally cut the rod too short, it will be useless and you will have to purchase another one.
How deep should a closet bar be?
However, you also need enough room behind the closet rod for the hangers to clear the back wall. In most cases, having the bar 10 inches (25 cm) off of the back wall works well.
What are the different types of closet bars?
There are a wide variety of closet bars available at most home improvement and hardware stores. In general, you can choose between metal and wood. You will also have the option of getting a solid bar or one that is adjustable.
How tall should a rod be?
In general, it's a good idea to mount a single rod at 5 feet (1.5 m) tall. A double rod set up should have the bottom rod mounted at 3.5 feet (1.1 m) and the upper rod mounted at 7 feet (2.1 m). If there is a shelf above the rod, you should make sure the rod is at least 2 inches (5.1 cm) below the shelf.
How to check for screws in studs?
You can also run a strong magnet along the wall to look for screws or nails that are in studs.
Do you need to add wood supports to a closet?
Add wood supports to the closet walls if needed. If the locations you have marked for the bar sockets do not have studs behind them in the wall, you will need to add supports to the wall. [11]
