Cut the conduit to the desired length, then use a drill to make two holes in the conduit, one at each end. Next, use screws to attach brackets to the wall on either side of the window, then slide the end of the conduit into the brackets. Finally, hang the curtains on the conduit. Can I use a pipe as a curtain rod?
How to make a custom DIY curtain rod?
To create a custom DIY curtain rod you’ll need to figure out how long to cut the rod. Don’t forget to keep in mind the width of each of the finials sticking out on either side as well. My rod needed to be 113″. I just measured the pipe and marked where I needed to cut with a Sharpie.
Can you use plumbing pipes as a curtain rod?
We think the size and shape of plumbing pipes make them a perfect stand-in for a curtain rod. Spray painted dark for a more industrial flair, this DIY project helps pull together DIY office decor. Pipe curtain rods are super popular right now and very easy to make! I used the following supplies to make the ones seen in my office’s progress:
How do you cut conduit for curtain rod?
We needed a 13.5′ curtain rod so we cut our conduit to 2 pieces of 6.75′ Use a Scotch Brite scrubber pad to sand the conduit pieces. Spray conduit along with the coupling, brackets, and finials with some primer. This is the one we like.
Can you spray paint a curtain rod?
Your pipe is what’s being used as the curtain rod and it’ll run from elbow to elbow. Don’t screw it into the 90-degree elbows just yet. After you have your curtain rod “arms” assembled, spray paint everything (including the long pipe) the color of your choice.
How do you make a galvanized pipe curtain rod?
0:252:48DIY Galvanized Pipe Rods & Drop Cloth Drapes | withHEART - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo it took some out-of-the-box. Thinking galvanized pipe is pretty inexpensive. And you can get itMoreSo it took some out-of-the-box. Thinking galvanized pipe is pretty inexpensive. And you can get it at Home Depot. We found all the attachments. And pieces we needed on the same aisle.
How do you make a homemade curtain rod?
4:239:2610 DIY Curtain Rods Ideas That Will Upgrade Your Window - YouTubeYouTubeStart of suggested clipEnd of suggested clipThen measure where you want your rod to sit on the wall and screw the pipe straps into the wall atMoreThen measure where you want your rod to sit on the wall and screw the pipe straps into the wall at each end slide the curtains onto the dowel. And then slide the dowel through your pipe straps.
How do you make a curtain rod out of conduit?
1:058:10how I made curtain rods using cheap EMT electrical conduit & a benderYouTubeStart of suggested clipEnd of suggested clipSo in order to make the curtain rods i decided to use half inch emt conduit emt conduit is prettyMoreSo in order to make the curtain rods i decided to use half inch emt conduit emt conduit is pretty interesting it's made of galvanized steel.
How do you put a curtain rod in a pipe?
2:027:39Installing Black Iron Pipe Curtain rods - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou're gonna need your black iron your fittings.MoreYou're gonna need your black iron your fittings.
What can u use instead of a curtain rod?
Pipe Rods. This one is a pretty common alternative. Many people turn to copper pipes when they need a substitute curtain rod. Copper pipes have a unique look about them which is what draws many folks toward it, but you can use any style of or look of pipe.
How do you make a curtain rod out of copper pipe?
DIY: Copper Curtain RodsClean off your curtain rods with water and soap.Measure your window and decide how far you want your rods to stick out.Screw two of the van hangers in place on either side of the window.Place the 1/2″ copper pipe inside the 3/4″ pipe and place your curtains on the copper curtain rods.More items...•
Can I use conduit as curtain rod?
It's insanely simple to put together. Just put one length of conduit in one end and tighten the screw, then do the same on the other side. And then, you have a DIY conduit curtain rod (almost)!
What is a conduit rod?
Conduit rods are used in pipe and cable pulling operations to assist in the installation of draw ropes, cables and winch wires – conduit duct rods can also be used as part of a CCTV or pipe cleaning system. Each are supplied with a free standing frame for easy handling, site mobility and ground stability.
Can you use PVC pipe for curtain rods?
PVC pipes pair well with wall hooks or drapery rod brackets. If you want to add decorative finials, insert a cork at each end of the hollow tube to help connect screw-in or pushpin finials, for example. To make returns on either side of the curtain, connect PVC elbows at each end to create 90-degree angles to the wall.
How do you hang curtains cheaply?
7:199:11CHEAP Way to HANG Curtains & Drapes - DAD HACK - YouTubeYouTubeStart of suggested clipEnd of suggested clipLike an 8-foot section 8-foot section but we also did it so we could add another anchor into theMoreLike an 8-foot section 8-foot section but we also did it so we could add another anchor into the wall. And it doesn't really affect any of our tricks. Because you always told drapes and in pairs.
Can I use a wooden dowel as a curtain rod?
By styling wooden dowels to look like copper rods, the DIY curtain rods were so inexpensive (just $12 apiece!) that we had money left over to craft statement-making tiebacks to match. Measure your window, then cut the 1-inch wooden dowel to a length at least 5 inches longer than your window is wide.
How do I make a curtain rod out of PVC pipe?
Cut the belt using utility knife.Step 2: Wrap the belt around the pipe and mark the point for making hole. ... Step 3: Measure and mark the place where you want the loop to go. ... Step 4: Insert the pipe into the belt loop and put the end caps to complete the curtain rod. ... Other Curtain projects you might like:
How do you build a wooden curtain rod?
3:3410:54DIY Wooden Curtain Rod | How To Install And Hang - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure to wipe off any wood glue that squeezes out between the two I repeated these exact sameMoreMake sure to wipe off any wood glue that squeezes out between the two I repeated these exact same steps to do the curtain rod for my back door and window area only back curtain rod is 84 inches long.
STEP 1
Assemble two sets of the floor flanges, nipples, and 90-degree elbows into “arms” like so:
STEP 2
Your pipe is what’s being used as the curtain rod and it’ll run from elbow to elbow. Don’t screw it into the 90-degree elbows just yet. After you have your curtain rod “arms” assembled, spray paint everything (including the long pipe) the color of your choice.
STEP 3
Once the paint has dried and is no longer sticky (I waited 24 hours), measure out the placement of where you’d like the curtain rod to be on your wall. Remember: curtains look best when they’re hung high and wide!
STEP 4
Next, screw one end of the long pipe into the end of the 90-degree elbow that’s attached to the arm that you just screwed into the wall.
STEP 5
If you slid your curtains onto the rod sans rings, fluff them up and space them out how you see fit. If you added curtain rings, it’s time to start ringing your curtains up!
Shopping list of supplies for curtain rods
First and foremost, go hunting around the store and find the metal pipes. You can’t miss them. They are about a million feet tall and stand straight up on end. When you find them, don’t play around with them. Imagine Lucille Ball and a conveyor belt. That would be you.
Next task at hand, cutting the pipe
Next, you will need to promise your hand in marriage to bribe the Home Depot workers to cut the metal pole for you. Do it. A girl has to do what a girl has to do.
What you Need
Detailed photos. Got ’em. You will need the photos for when you want to show off your mad DIY designer skills to the dudes in the hardware store.
Curtains
I adore the curtains at West Elm. Lurve them. I may have left some drool on them the last time I visited the store. I rubbed the curtains on my cheeks … and purred like a kitten. That good. I’m not embarrassing to shop with. At all.
How long should a curtain pipe be?
Pipes should be cut to around 8 inches (4” per side) longer than the outer window trim measurement of your window casing. If your curtains are a very thick material, you may want to add an inch of pipe to each side so that the curtains don’t totally obfuscate the light from entering.
How long should a pipe be cut for a window?
Pipes should be cut to around 8 inches (4” per side) longer than the outer window trim measurement of your window casing.
Where do couplers sit on a curtain rod?
The coupler will sit in the center support rod , with the screws pointed towards the wall and won’t really be visible. You won’t need to worry about the curtains gliding over it.
How to make curtains slide smoother?
Before putting up the curtains on the rod, add some paste wax with a cloth or paper towel to the top half of the curtain rod to help make sure the grommets slide nice and smooth every time you open and close the curtains.
What to do when spray paint is dry?
When the spray paint is dry, add a clear coat for durability. We used our favorite Crystal Clear Enamel.
What scrubber pad to use for conduit?
Use a Scotch Brite scrubber pad to sand the conduit pieces.
How to shorten a cork?
Using a utility knife and working over a cutting board or surface that is safe to cut on, shorten a cork.
Can you use pliers to open conduit?
The larger your conduit, the more trouble you might have finding brackets that fit it. But you can usually use pliers to open the bracket up a little and shove the coupling in there to expand it and make it work. You want to do this before you paint it, though. Finials - Pick out some finials you like too.
Can you extend a curtain rod on either side of a large window?
If you want to extend your curtain rod on either side of a large window (and believe me, you really do), or you have a couple of windows to dress, you either need to
How to attach a curtain ring to a curtain?
To attach the rings, pinch the section of curtain you want the ring to be attached to, then just clip the ring right onto the pinched fabric. Make sure you set your rings low enough that they will barely show over the top of your curtain. That’s it. It’s so easy.
Where do you clip a curtain clip?
When you attach the clips you are going to clip them on the back of the curtain, not the top edge. This creates the pleat look.
Do you need a center support for curtain rods?
I have done this a couple of times. Even cheap curtain rods are more expensive that doing it this way, and the bonus is that you don’t need a center support because the conduit is not flexible, just make sure your hangers are in a stud, which you can usually find because you are putting the hangers at the end of the window where it is framed. I did this in my sunroom and took steelwool to the pipe because everything in my room is stainless steel. Looks awesome and even better, it is one solid piece so you don’t have the part in the middle where they connect and the rings always get caught up in it.
Does a pipe cutter cut smooth?
The pipe cutter made a very smooth cut. I was actually impressed that the edge of the pipe wasn’t sharp at all. Double bonus for not slicing my finger on the end of a sharp pipe!
Is Preston curtain rod extendable?
Preston has also provided a link to an extendable curtain rod which in my opinion is a lower quality than what you have made here. Opening an closing curtains when there is the bump from the extension even when there is the plastic grommet in there to make it smoother can be a pain and not having that because you put some time into a very nice DYI project is well worth the effort put in.