How do you make a fiberglass slide?
- Mix two gallons of the fiberglass epoxy resin and the hardener (2:1 ratio) in a plastic bucket.
- Use lacquer thinner and a cheesecloth rag to scrub the surface of the coated slide.
- Lay the fiberglass fabric over the slide, being sure that the center line of the fabric is in the middle of the slide.
How do you build a fiberglass slide from plywood?
Building a home fiberglass slide can easily be accomplished by framing an elevated plywood trough that has been covered with multiple layers of fiberglass. Use a tape measure and framing square to mark out two 30-by-96-inch pieces of 3/4-inch plywood and an additional 30-by-48-inch piece. Use a circular saw to cut all three pieces.
How do you harden a fiberglass slide?
Mix two gallons of the fiberglass epoxy resin and the hardener (2:1 ratio) in a plastic bucket. Use a new fiberglass roller and apply three coats of epoxy resin to the entire interior of the slide, spacing the applications two hours apart. Allow the epoxy resin to cure for 24 hours.
What is the best way to build up the fiberglass?
"Chopped mat" can be used if you have access to a "chop gun", and you can build up the fiberglass as thick as you want it in one application. To ensure an even impregnation of resin to the cloth, try sandwiching the cloth between two larger sheets of clear plastic sheeting.
Can you put a fiberglass slide in a pool?
You can even have a flume slide. It makes the slide more fun and very slippery but it complicates the building procedure. You can easily purchase a fiberglass slide from a pool supply company. Some slides require little assembling and some slides come with the customizable kits. You need to select the slide, which fits into your pool perfectly.
How do you make a fiberglass slide slippery?
How to Make a Slide Slippery the Safe WayMake a Cleaning Solution. Make a cleaning solution using warm water and a mild dish detergent. ... Scrub Down the Slide. You'll want to use an abrasive rag or hand towel to scrub the slide from top to bottom. ... Let it Dry. ... Wax the Slide Itself. ... Sand the Slide Surface (If Needed)
Can I build my own pool slide?
DIY Backyard Water Slide You're going to be making a turbo slide off an old swing set. You'll need to get some boards or four by four kinds of wood that will help you erect this turbo slide. So you'll build the slide on the deck in the corner of your pool to get started or any other way you figure out.
How do you build a waterslide?
0:022:48Waterslide | HOW TO BUILD... EVERYTHING - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo in a waterslide. You would always build this steel frame first because you need to have a strongMoreSo in a waterslide. You would always build this steel frame first because you need to have a strong foundation. And this waterslides frame is built with cylinders.
What is the best material for a water slide?
For a wider slide usable by everyone (kids AND adults) use a 8' x 100' roll in either 4 mil clear or 6 mil clear. 6 mil is recommended for durability, especially if you are planning on reusing the slide in the future.
How do you make a homemade slide?
1:275:46How To Make: DIY Slide with Sides - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're cutting these notches into the metal here you need this either when it's flat or when you bentMoreWe're cutting these notches into the metal here you need this either when it's flat or when you bent it that'll make it much easier to fold the whole thing up fold.
How much does it cost to make a water slide?
Cost: The range in cost is wide. A simple, prefabricated slide with ladder might be installed for $4,000, while some of the tantalizing slides shown here could easily top $100,000.
How do you make a homemade slip and slide?
DIY Slip 'N Slide TutorialSTEP 1: Choose a location for your DIY slip 'n slide. ... STEP 2: Fold the plastic sheeting in half lengthwise. ... STEP 3: Use landscape anchor pins to fix the sheeting in place. ... STEP 4: Turn on the hose; consider adding baby soap for extra slipperiness. ... STEP 5: Have a blast!
What material are waterslides made of?
They are typically made of a thick strong PVC or vinyl and nylon, and are inflated using an electric or gasoline powered blower. The water slide is attached to a water hose in order to generate the supply of water.
How do you make a water slide decal?
11:2414:50How to Make Waterslide Decals for Tumblers - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo I like to use like a squeegee from 651 vinyl that I can just stick my tumbler right on top ofMoreSo I like to use like a squeegee from 651 vinyl that I can just stick my tumbler right on top of just to keep it steady. And you'll know that your waterslide decal is ready when you're able to slip.
What do you put at the bottom of a slide?
This fits your .KidWise Fanny Pads are a great way to protect areas that suffer wear from playground traffic and keep your play area beautiful and safe.Place under swings, slides, or any place foot traffic will wear away protective safety surfaces.Set of 2 Fanny Pads: each are 23.More items...KIDWISE 1.5 Inch Fanny Pads - Green Rubber Safety Mats (Set of 2)https://www.amazon.com › KIDWISE-1-5-Inch-Fanny-Padshttps://www.amazon.com › KIDWISE-1-5-Inch-Fanny-PadsSearch for: What do you put at the bottom of a slide?
Does plastic sheeting work as a slip and slide?
We tried some 6-mil plastic sheeting, 6 feet wide by 50 feet long for our sample slide, since it gave a nice width of sliding surface, and the length fit across our front yard. But, depending on your location, you may want a smaller or bigger (yeah!)Build an Awesome DIY Slip 'n' Slide for Summer Fun | WIREDhttps://www.wired.com › 2012/06 › diy-slip-and-slidehttps://www.wired.com › 2012/06 › diy-slip-and-slideSearch for: Does plastic sheeting work as a slip and slide?
What do you put under water slides?
For inflatable water slides and slip and slides, a tarp can help protect the ground from turning into a muddy, soggy mess.What is a Tarp and Why Do I Need One for my Bounce House?https://www.pogobouncehouse.com › blog › 2020/11/18https://www.pogobouncehouse.com › blog › 2020/11/18Search for: What do you put under water slides?
How to put fiberglass fabric on a slide?
Lay the fiberglass fabric over the slide, being sure that the center line of the fabric is in the middle of the slide. Note: This is an approximate fitting only since the fabric will be overlapped beyond the outside edges of the slide. Work the fabric down into the corners of the slide and up the walls of the slide and over its outside edges. ...
Why are pool slides fiberglass?
They are typically fiberglass because of the slick surface and because it can be molded into curved and twisted shapes. Pool slides are attached to an elevated assembly that allows people to climb a ladder to an upper surface from which to mount the slide and glide down into the water. Building a home fiberglass slide can easily be accomplished by ...
How to make a slide out of epoxy?
Step 1. Mix two gallons of the fiberglass epoxy resin and the hardener (2:1 ratio) in a plastic bucket. Use a new fiberglass roller and apply three coats of epoxy resin to the entire interior of the slide, spacing the applications two hours apart. Allow the epoxy resin to cure for 24 hours.
How long does it take for a fiberglass slide to cure?
Allow the fiberglass slide to cure for 48 hours. Use a power sander and 120-grit paper to sand the inside surfaces of the fiberglass slide until they are super slick. Use construction L-brackets to attach the top of the slide to the upper edge of the slide platform.
How to apply epoxy resin to a slide?
Use a new roller to roll the cloth heavily into the wet surface of the slide. Apply another heavy coat of epoxy resin to the top surface of the fabric. Repeat this process two more times, eight hours apart, and apply a final coat to the upper surface of the third layer of fabric.
How is fiberglass made?
Fiberglass starts off as a liquid. This liquid is then extruded through tiny little holes, which turn it into thin strands of threads. These threads are coated with a chemical solution and bundled together to form rovings, or long bundles of fibre. Add a bit of resin and you have strong, durable, flexible fiberglass.
How to work with fiberglass?
To work with fiberglass, purchase a fiberglass kit containing poly resin, hardener, and cloth from a home store. Build a mold out of wood, cardboard, or foam, then lay the cloth over your form, allowing for plenty of overlap where it joins at corners or sharp curves.
What is the best way to clean fiberglass?
Acetone is great for cleaning up fiberglass because it's strong and evaporates quickly. Just be sure not to soak any portion of the fiberglass in acetone, and keep acetone away from any caulking, plastic, or rubber. ...
What material to use for molds?
Use cardboard, plywood, MDF, or other stiff materials for molds with linear or geometric shapes. These stiffer materials are best for large projects like dog houses or even boats. For these molds, cover the entire surface either with wax paper, or a good, even coat of paraffin wax.
Can you paint fiberglass molds with wax paper?
Then, paint with a polyurethane or alkyd enamel, if desired. Remove your fiberglass from the form. If you have covered your form or mold with wax paper or paraffin wax, you should be able to peel the form from inside the shape, or peel the shape off of the form. The fiberglass will not stick to the wax.
Can you mix resin in a plastic container?
Measure an appropriate amount of resin in a metal container. A large can or metal bowl will work, but it should be of a disposable nature. Resin can be mixed in a clean plastic container, but because it generates heat when it sets, extreme care should be taken if you use one. ...
Can you put fiberglass in ice water?
Community Answer. Yes, place the container with fiberglass in a larger container with ice water but be careful to ensure that the job is properly planned out. Meaning, ensure that the glass is cut to proper size, etc., so that you may work quickly, since condensate could contaminate the fiberglass mix. Thanks!
How deep should a pool slide be?
Three feet is ideal as a minimum, but many professionals prefer a depth of 10 feet. Figure out how you are going to secure the slide to the pool area and the ladders. You will need to figure this out. Do not puncture the sides of the pool!
How to bring ladder into ground?
Ideally, you will have a way to bring the ladder firmly into the ground. Remember that you might need to remove tiles or alter a concrete area if you have to lock a slide into the ground. Sadly, you might have to plan around that as well. Measure, measure, measure. This is a must for any construction project.
Can you use a hose to clean a pool slide?
Most cleaning wipes are totally safe with pool slides, since plastic doesn’t corrode like metal does. If you just need to give your slide a quick clean, use a hose to rinse it down. To get rid of mold, make sure to wipe down the slide with white distilled vinegar or another antifungal substance.
Is it safe to add a slide to a pool?
Like with all other DIY pool projects, it’s important to remember that adding a pool slide is something you need to think about safety-wise. If you have children who are prone to accidents or small toddlers, it might not be safe quite yet.
Can you put cement weights on a ladder?
In most cases, having cement weights on the bottom of the ladder will do just fine. Test the slide with your hand to see if it needs additional support.
Do you need water to make a pool slide?
While water is not necessary for the slide to work, you can add plumbing to run water there if you so choose. There are a lot of different ways to make a pool slide happen in your home. We’re going to give you a quick run-through on how to make your own pool slide.
Can you bolt a slide to a support?
It’s often best to bolt the slide’s sides to the support. If you have a slide with prefab holes, you can usually secure them there. Double-check to make sure that the slide is properly positioned. Once you have made sure that the slide has enough overhang into the pool, you will need to move to the next step.
How to get dirt off a slide?
To do this safely, we recommend rubbing wax paper over the entire slide surface. Rubbing the wax paper transfers the food-safe wax onto the surface of your slide.
How to clean a slide from top to bottom?
Scrub Down the Slide. You’ll want to use an abrasive rag or hand towel to scrub the slide from top to bottom. Once the slide is free of the years of outside dirt, rinse off the soapy solution with the garden hose. Let it Dry.
Why does my slide lose its slickness?
One of the main reasons that a slide loses its slickness is that it becomes dirty over time — that’s why you’ll want to start by cleaning the slide. Here’s how we recommend cleaning and polishing your slide: Make a cleaning solution using warm water and a mild dish detergent.
Is it fun to slide down a slide?
For kids, few things are more fun than rocketing down a slide, whether it’s at a park or in their backyards. However, over the years and over thousands of rides down, plastic slides become less slippery, and thus, less fun. There is good news though — you can do something about it!
Can you use wax paper on a slide?
Rubbing the wax paper transfers the food-safe wax onto the surface of your slide. While wax paper is our preference when polishing a playground slide, some parents like to use spray-on wax to achieve the same effect.
Step 2 - Buy A Slide
- You can easily purchase a fiberglass slidefrom a pool supply company. Some slides require little assembling and some slides come with the customizable kits. You need to select the slide, which fits into your pool perfectly.
Step 3 – Building The Slide
- Now build your slide by connecting the parts with the given hardware tools. Follow the instructions given by the company carefully. The pieces should be flushed where they hook up so they must not create a safety risk.
Step 4 – Positioning The Slide
- You should position the slide in such a way that it suspends over the border of your pool slightly. Make sure that the people who utilize your slide end up in the water and not over the border of your pool. Lastly, anchor your slide to the concrete or fasten it to the floor by using bolts Step 5 - The process of Attaching the Slide to the Ladder Put up your stepladder near the deep end of yo…
Step 6 – Attaching The Slide
- To attach your slide to the stepladder you need to have carriage bolts, they usually have rounded heads. Place the top of the slide at the top of your stepladder. Then drill holes through your slide into the top/head of the stepladder and fasten the two together by using carriage bolts. Use two scatterings out as easily as they can set off and still connect to the ladder. Then drill a middle ho…