how do you make a metal pipe shelf

DIY INDUSTRIAL PIPE SHELF

Full Answer

How to build a pipe shelf?

The Build – Instructions, Tips, & More

• Project Description. Make a shelving unit that features rungs, support brackets, and four shelves. ...
• Gather Supplies and Tools. ...
• Make the Pipe Shelves Plan. ...
• Cut the Boards. ...
• Finish the boards. ...
• Assemble the Pipes. ...
• Install the Flanges on the Wall. ...
• Paint the Clamps. ...
• Screw the Boards in Place. ...

How to build industrial pipe shelves?

Step-By-Step to Build Your Industrial Pipe Shelves

• Assemble one bracket at a time and lay out on the floor.
• Be very sure to line up every fixture so they are exactly in line with one another. ...
• Hold assembled unit against the wall at pre-measured location (this should line up with the studs). ...
• Use a balance to ensure it is straight and mark the walls for the screw anchors.
• Align unit and screw in place. ...

How to create copper Pipe shelving?

first, we use a four foot level to draw a straight and level line across the wall at the height of our shelves. next, i use a shorter two-foot level to extend the stud marks eric drew earlier, down to our shelf line. finally, with the brackets laid out in front of each stud, we begin passing the copper pipe through the holes in each bracket. ron:

How to build simple DIY closet shelves?

Instructions

• Remove everything from the closet including old shelves you will no longer be using. ...
• Cut the strips of MDF to the correct length for your shelves. ...
• It is easiest to paint all of the pieces of wood for your closet shelves before installing them.
• Cut two side supports for each shelf from 1"x2" pine boards. ...
• Make sure that each shelf support is level. ...

More items...

How do you make a metal pipe rack?

0:051:37How to make iron pipe shelves - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd finish them with a coat of Danish. Oil. You can make these shelves in a variety of differentMoreAnd finish them with a coat of Danish. Oil. You can make these shelves in a variety of different sizes and configurations.

How do you make a freestanding pipe shelf?

1:365:39Black Pipe Bookshelf | Build It | Ask This Old House - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo i'm going to drive this in i'll show you what we're going to do. Drive that down until the threadMoreSo i'm going to drive this in i'll show you what we're going to do. Drive that down until the thread. Starts to come.

What kind of pipe is used for pipe shelves?

2:334:37How to Make an Industrial Pipe Shelf - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow that my shops are done is time to the Titans here's all the pipes you'll need I used half inchMoreNow that my shops are done is time to the Titans here's all the pipes you'll need I used half inch black steel pipe but you could use three quarter inch pipes if you wanted more bulky.

How do you make an iron pipe shelf bracket?

0:212:55How To Make Industrial Iron Pipe Shelves - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn the length depends on how many shelves you want to make 4 iron piping each shelf will need fourMoreOn the length depends on how many shelves you want to make 4 iron piping each shelf will need four half-inch flanges two half-inch two and a half inch nipples.

Do it yourself pipe shelf?

HomeMade Modern DIY Pipe ShelvesStep 1: Supplies + Tools. 3/4" Pine Boards. ... Step 2: Download the Pipe Shelves Plan. ... Step 3: Cut the Boards. ... Step 4: Sand + Finish the Boards. ... Step 5: Assemble the Pipes. ... Step 6: Screw the Flanges to the Wall. ... Step 7: Paint the Pipe Clamps. ... Step 8: Secure the Boards.More items...

How much weight can a pipe shelf hold?

How much weight can a pipe shelf hold? According to the internet, pipe shelves can hold 140 pounds.

How do you make easy shelves?

0:122:57How to Build a Simple Shelf - YouTubeYouTubeStart of suggested clipEnd of suggested clipSquirt a bead of wood glue onto the spacer. And use a scrap of one by two to position the ShelfMoreSquirt a bead of wood glue onto the spacer. And use a scrap of one by two to position the Shelf before pinning it.

How do you make an industrial pipe bookcase?

0:333:39DIY INDUSTRIAL PIPE BOOK SHELF - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the first thing I did was rip my piece of wood to the width that I. Wanted. Then I crosscut theMoreSo the first thing I did was rip my piece of wood to the width that I. Wanted. Then I crosscut the lengths of the shelf. The overall dimensions of each shelf are 12 inches deep by 24 inches wide.

How do you make a pipe bench?

0:182:56How to Make a Pipe Bench - YouTubeYouTubeStart of suggested clipEnd of suggested clipStart by creating the base. Clean your pieces up with some mineral spirits before you start and you'MoreStart by creating the base. Clean your pieces up with some mineral spirits before you start and you're basically just making 2h shapes you can find the exact diagram for the pieces.

How do you make a triangular shelf?

0:5310:51Easy DIY Triangle Shelves | The Perfect Beginner Woodworking ...YouTubeStart of suggested clipEnd of suggested clipOff cut off one end and just rotate it just like that and then cut off another I know that seemsMoreOff cut off one end and just rotate it just like that and then cut off another I know that seems weird but sometimes I'll flip the board a different way and then cut that angle.

What is a shelf bracket called?

Types of shelf supports: L-shaped shelf supports are named shelf bracket and they are a subset of angle brackets. Cabinet shelf support, wardrobe shelf support, shelf pin, shelf support peg, shelf support push, plug-in shelf support - when used in a wardrobe or cabinet.

How do you make a shelf out of copper pipe?

0:031:39How to Create Copper Pipe Shelving - YouTubeYouTubeStart of suggested clipEnd of suggested clipAgain stroke the frame without glue to check that it fits. Okay we've got it all assembled now. SoMoreAgain stroke the frame without glue to check that it fits. Okay we've got it all assembled now. So we just need to adhere all of the joints together. So they're good and strong using an epoxy resin.

How do you make a shelf out of PVC pipe?

0:4011:37How I Made Industrial Shelving For A Fraction Of The Price! (Full Tutorial ...YouTubeStart of suggested clipEnd of suggested clipAnd traced where it needed to be then we took our pvc plugs we drilled a hole through them. And thenMoreAnd traced where it needed to be then we took our pvc plugs we drilled a hole through them. And then we attached them to the wall using drywall screws then we just added a little bit of glue.

How much weight can a floating pipe shelf hold?

But how much weight can a floating shelf hold? TLDR: A floating shelf can hold 45-50 pounds for every wall stud that your floating shelf bracket is attached to. For instance, a 3' shelf that's attached to two wall studs can safely support ~100 pounds.

How do you make a free floating shelf?

1:304:42How to Make Floating Shelves - DIY Wood Floating Shelves - YouTubeYouTubeStart of suggested clipEnd of suggested clipSupport and attach the front piece of the shelf box with wood glue and nails. Sand the entire shelfMoreSupport and attach the front piece of the shelf box with wood glue and nails. Sand the entire shelf box using a sander and 220 grit sandpaper.

How do you make copper pipe shelves?

0:031:39How to Create Copper Pipe Shelving - YouTubeYouTubeStart of suggested clipEnd of suggested clipAgain stroke the frame without glue to check that it fits. Okay we've got it all assembled now. SoMoreAgain stroke the frame without glue to check that it fits. Okay we've got it all assembled now. So we just need to adhere all of the joints together. So they're good and strong using an epoxy resin.

How many straps are needed to hold shelves in place?

Rookie Tip: Note in the picture there are 8 straps to hold the shelves in place, but we actually only ended up needing four. Also, you may need to spray paint two different times to get some of the areas that you missed the first time (i.e. the bottom of the safety clips). And the last thing — the paint did adhere to the pipes but be super careful not to scratch any of these parts on each other because the paint will scratch/chip off. <– again, just some helpful tips.

How high should a baby be to touch shelves?

When the baby is old enough to start standing up in the crib, my sister will lower the mattress and the baby will have to be able to reach OVER 4 1/2 feet high to touch the pipes of the shelves. And by the time the baby is over 4 and 1/2 feet, I have a feeling those shelves will be long gone. =)

Can you spray paint galvanized metal?

Yes, when a spray paint says it's not to be used on galvanized metals, it means that it'll flake off fast because the paint doesn't adhere to the zinc coating too well. To address that you either have to use a base coat for galvanized surfaces first or leave the galvanized items outdoors for a bit to let them develop a patina. In either case your desired spray paint will have good adherence afterwards.

Can you DIY pipe shelves?

We knew we could DIY these industrial pipe shelves without spending a ton of time or money and that’s exactly what we did! We learned a few tips along the way too and are spilling to the beans so your project goes as smoothly as possible!

Can you cut pipe threads down?

Thanks so much, Sherri! I bought these pipes with the threads on both sides however, you can get them cut down to size and the hardware store should add threads per your request. Hope this helps, good luck!!

Can galvanized pipes be painted black?

Someone may have already suggested this, but if you use galvanized pipe for gas lines it is already painted black (this is done to tell gas pipes from water pipes). They are already pretty industrial looking and would save the money and labor involved in painting.

Easy DIY Pipe Shelves To Save Space

We have given so many DIY ideas for you to make your home more beautiful or for fun and entertainment. This time we offer 30 DIY Pipe Shelves Ideas, which are easy to make from an ordinary pipe and also very durable. The shape and size are on you and you can even take it up a notch and paint them, or add some colorful details to them.

How To Build Pipe Shelves

What if you could have the look of a trendy pipe accent without paying hundreds to a craftsman? These shelves are quicker and easier to assemble than you’d think, and won’t break the bank. Here are the step-by-step instructions for how to build these shelves. Build your own stylish, versatile pipe shelves.

DIY Industrial Wall Shelves

This DIY tutorial is a step-by-step guide to making an easy, inexpensive, and super durable Industrial Wall Shelf. The supply for the iron pipe cost about $20 and the wood is a cheap piece of wood. This industrial wall shelf is perfect for displaying home decor items, pictures, or other mementos.

How To Make An Industrial Pipe Shelf

This is a perfect space saver for an industrial-style dining room. It is also used in other rooms like the bathroom or even an office. This DIY shelf is made with industrial piping and the creator used wooden planks to create a solid shelf. It can carry much weight at once because of its strong materials.

How To Build DIY Industrial Pipe Shelves

This is the ultimate guide on how to build DIY industrial pipe shelves that won’t break the bank. It includes step-by-step instructions, pictures, and how-to videos. This easy tutorial will guide you through building DIY industrial pipe shelves for a fraction of the cost.

DIY Pipe Shelves From Scratch

Beauty and function are a timeless combination, and this is the perfect example. This shelf is made with a galvanized metal pipe, giving it that industrial style. The board was painted in a bright white, making it even more visually appealing. With countless possibilities of configuration, this one is sure to fit your needs.

DIY Industrial Pipe Shelves

This industrial pipe shelf is the perfect storage solution if you’re having trouble reaching things out of your reach. Whether you install it in your bathroom or kitchen, the shelves will add a nice touch to your space. You’ll have quick and easy access to all of your belongings with this shelf. There are so many great ways to use them.

Why do people build pipe shelves?

To save on costs, flexibility, personal design, and even for fun! Building your own shelf can ensure you have something that is personal, unique, and matches the looks you're going for.

Why is the book shelf attached to the ceiling?

Taking advantage of room space, this shelf is attached to the ceiling to allow for extra floor space. A great idea for any book lover!

What is a Kee Klamp shelf?

This handy shelving unit functions both as a workbench and storage unit. The shelf is built with Kee Klamp fittings and pipe. The addition of the hooks increases functionality and can be found here.

Why is the Kee Klamp shelf unique?

This unique design has varying levels including some that swivel in different directions. The shelf is used to save space in a small studio. The flexibility and adjustability of Kee Klamp allowed this customer to create a unique custom built design that could not be built with other materials.

What is the black pipe on a desk?

The dark wood finish along with the black pipe featured in this gorgeous rustic shelving unit create a "warm", welcoming vibe in the room. The integration of the extended shelf to create a built in desk is a great addition that makes this unit even more functional and convenient. You can read all about the project here.

How many columns are on a 3 tiered shelf?

This three-tiered shelf was designed as a retail display. The reclaimed lumber is supported by four columns on the bottom shelf and then two columns on the top shelf.

Can pipe fittings be taken apart?

The great thing about using pipe fittings is that they can be taken apart and put back together to build almost anything. That's exactly what happened with this shelf. Described as "Pipe Shelf Remix" this DIY shelf was deconstructed from a previous pipe shelf into this beautiful unit.

Step 2: Measure 3 Times Cut Once! Then Weld

I need space in my newly almost completed attic. so I decided on using black pipe to make shelves and instead of buying precut lengths I decided to cut and weld it all together.

Step 4: Wood

I cut the 12 ft boards in half then drilled pocket holes and glued and screwed them together to make them 24in x 6ft long. after the glue set I burnt the wood to darken it then I stained it with dark stain

Step 6: Storage Compartments

I bought 2 wooden crates from home depot and stained and charred the wood to match then coated them as well as the shelves with some polycrylic...

Where should a shelf sit on a pipe?

If you plan on putting a cap on the end of the pipe then you should plan for the shelf to sit in between the cap and the flange. You can see in the photograph above how the shelf does not sit on top of the caps. This would make the shelf sit unevenly. These pipes come in pre-made lengths.

How to determine how long a shelf pipe needs to be?

Use the width of your shelf to determine how long the pipe needs to be. It should be cut measuring all the way from one end like in the photo:

What size pipe do I need for a shelf bracket?

1. Black Pipe Flange. You need one of these for each shelf bracket that you make. I generally stick to 3/4″ because I think it looks the best with wood like a 2×4, but 1/2″ will work too in certain situations. If you can’t find one I suggest buying online it from Home Depot or Amazon.

How to weld a pipe in a vice?

Take your pipe and put it in a vice with the cut end on top. Place the flat steel square on the end and weld around the edge.

Why do I put a shelf on the wall?

The reason I do it is because I like to have a secure shelf that I know is not going to come off the wall.

What size steel do you need to cut 3/4" pipe?

If you are cutting your pipe to length and welding a cap on, then you will need a piece of flat steel. It needs to be in the neighborhood of 1″x1/8″ for 3/4″ pipe.

Can you put a cap on a pipe?

Pipe – Cut to Length or Stock Length. If you plan on cutting pipe to length, you will not be able to put a cap onto the end of it unless you get threads machined onto the end. This means you can either leave the end open, or weld a small piece of flat steel onto the end to cover the hole up.

What do you use to secure boards to pipes?

Use the pipe hangers to secure the boards to the pipes.

What is a pipe clamp?

Pipe clamps are metal loops that can be used to connect the pipes to the boards. Use 2 clamps per horizontal pipe support and fasten them with 5/8" long screws. Plugs make it easy to adjust and level the shelves, but are not essential.

Can you use iron plumber pipe to make shelves?

There are a lot of ways to use iron plumber's pipe to make shelves. Here's the way that has worked well for me. Pipe shelving systems are not cheap but are a great investment because they can be disassembled and adapted to almost any setting. If you're renting your current home or move often, they're an excellent alternative to moving giant ...